BOSCH GBH 18V-26 Cordless Rotary Hammer User Manual

BOSCH GBH 18V-26 Cordless Rotary Hammer User Manual

www.boschtools.com

General Power Tool Safety Warnings

⚠ Read all safety warnings, instructions, illustrations and specifications provided with this power tool. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury.

SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE REFERENCE

The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.

1. Work area safety

• a. Keep work area clean and well lit. Cluttered or dark areas invite accidents.
• b. Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.
• c. Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.

2. Electrical safety

• a. Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock.

• b. Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.

• c. Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.

• d. Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric
  shock.

• e. When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.

• f. If operating a power tool in a damp location is unavoidable, use a Ground Fault Circuit Interrupter (GFCI) protected supply. Use of an GFCI reduces the risk of electric shock.

3. Personal safety

• a. Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury.
• b. Use personal protective equipment. Always wear eye protection. Protective equipment such as a dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries.
• c. Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power source and / or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energizing power tools that have the switch on invites accidents.
• d. Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury.
• e. Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.
• f. Dress properly. Do not wear loose clothing or jewelry. Keep your hair and clothing away from moving parts. Loose clothes, jewelry or long hair can be caught in moving parts.
• g. If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust-related hazards.
• h. Do not let familiarity gained from frequent use of tools allow you to become complacent and ignore tool safety principles. A careless action can cause severe injury within a fraction of a second.

4. Power tool use and care

• a. Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed.
• b. Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.
• c. Disconnect the plug from the power source and/or remove the battery pack, if detachable, from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.
• d. Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.
• e. Maintain power tools and accessories. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.
• f. Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.
• g. Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation.
• h. Keep handles and grasping surfaces dry, clean and free from oil and grease. Slippery handles and grasping surfaces do not allow for safe handling and control of the tool in unexpected situations.

5. Battery tool use and care

• a. Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack.
• b. Use power tools only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire.
• c. When battery pack is not in use, keep it away from other metal objects like paper clips, coins, keys, nails, screws, or other small metal objects that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or a fire.
• d. Under abusive conditions, liquid may be ejected from the battery, avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns.
• e. Do not use a battery pack or tool that is damaged or modified. Damaged or modified batteries may exhibit unpredictable Behavior resulting in fire, explosion or risk of injury.
• f. Do not expose a battery pack or tool to fire or excessive temperature. Exposure to fire or temperature above 265 °F may cause explosion.
• g. Follow all charging instructions and do not charge the battery pack or tool outside the temperature range specified in the instructions. Charging improperly or at temperatures outside the specified range may damage the battery and increase the risk of fire.

6. Service

• a. Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.
• b. Never service damaged battery packs. Service of battery packs should only be performed by the manufacturer or authorized service providers.

Safety Rules for Rotary Hammers

• a. Wear ear protectors. Exposure to noise can cause hearing loss.
• b. Use auxiliary handle(s), if supplied with the tool. Loss of control can cause personal injury.
• c. Hold the power tool by insulated gripping surfaces, when performing an operation where the cutting accessory may contact hidden wiring. Cutting accessory contacting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock.
• d. Use clamps or another practical way to secure and support the workpiece to a stable platform. Holding the work by hand or against your body leaves it unstable and may lead to loss of control.
• e. Do not drill, fasten or break into existing walls or other blind areas where electrical wiring may exist. If this situation is unavoidable, disconnect all fuses or circuit breakers feeding this worksite.
• f. Use a metal detector to determine if there are gas or water pipes hidden in the work area or call the local utility company for assistance before beginning the operation. Striking or cutting into a gas line will result in explosion. Water entering an electrical device may cause electrocution.
• g. Always use the side handle for maximum control over torque reaction or kick-back. Never attempt to operate this tool with one hand. The slip clutch engages if you firmly control the tool during a torque reaction or kickback.
• h. Always wear safety goggles or eye protection when using this tool. Use a dust mask or respirator for applications that generate dust. Safety goggles or eye protection will help deflect fragments of the material that may be thrown toward your face and eyes. Dust generated or gases released from the material you are cutting (i.e. asbestos insulated pipes, radon) may cause respiratory difficulties.
• i. Use thick cushioned gloves and limit the exposure time by taking frequent rest periods. Vibration caused by hammer-drill action may be harmful to your hands and arms.
• j. Position yourself to avoid being caught between the tool or side handle and walls or posts. Should the bit become bound or jammed in the work, the reaction torque of the tool could crush your hand or leg.
• k. Do not strike the bit with a handheld hammer or sledgehammer to attempt to dislodge a bound or jammed bit. Fragments of metal from the bit could dislodge and strike you or bystanders.
• l. Never place the tool down until the bit or accessory has come to a complete stop.
• m. Do not use dull or damaged bits and accessories. Dull or damaged bits have a greater tendency to bind in the workpiece.
• n. When removing the bit from the tool avoid contact with skin and use proper protective gloves when grasping the bit or accessory. Accessories may be hot after prolonged use.
• o. Do not run the tool while carrying it at your side. A spinning bit could become entangled with clothing and injury may result.

Safety instructions when using long drill bits with rotary hammers

• a. Always start drilling at low speed and with the bit tip in contact with the workpiece. At higher speeds, the bit is likely to bend if allowed to rotate freely without contacting the workpiece, resulting in personal injury.
• b. Apply pressure only in direct line with the bit and do not apply excessive pressure. Bits can bend causing breakage or loss of control, resulting in personal injury.
• c. Never operate at higher speed than the maximum speed rating of the drill bit. At higher speeds, the bit is likely to bend if allowed to rotate freely without contacting the workpiece, resulting in personal injury.

Additional Safety Warnings

GFCI and personal protection devices like electrician’s rubber gloves and footwear will further enhance your personal safety.
Develop a periodic maintenance schedule for your tool. When cleaning a tool be careful not to disassemble any portion of the tool since internal wires may be misplaced or pinched or safety guard return springs may be improperly mounted. Certain cleaning agents such as gasoline, carbon tetrachloride, ammonia, etc. may damage plastic parts.

Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:

• Lead from lead-based paints,
• Crystalline silica from bricks and cement and other masonry products, and
• Arsenic and chromium from chemicallytreated lumber.

Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles.

Symbols

Important: Some of the following symbols may be used on your tool. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the tool better and safer.

Important: Some of the following symbols may be used on your tool. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the tool better and safer.

Getting to Know Your Product

Disconnect battery pack from tool before making any assembly, adjustments or changing accessories. Such preventive safety measures reduce the risk of starting the tool accidentally.

Bosch GBH18V-40C Cordless Rotary Hammer

1. Dust shield
2. Accessory Locking Sleeve
3. Ventilation openings
4. Mode Selector Dial
5. Vibration Damper
6. Lock-On / Lock-Off Button
7. Main Handle (insulated gripping surface)
8. On/Off Switch
9. User interface
10. Battery pack release button
11. Battery pack
12. Connectivity module compartment
13. LED Work light
14. Auxiliary Handle (insulated gripping surface)

Specifications

Battery Packs / Chargers: Please refer to the battery/charger list, included with your tool.
NOTE: For tool specifications refer to the nameplate on your tool.

Intended Use

The power tool is intended for hammer drilling in concrete, masonry and stone, as well as for chiseling work.

With the Bluetooth® Low Energy Module GCY 42 inserted, power tool data and settings can be transferred between the power tool and a mobile device by means of Bluetooth® wireless technology.

Assembly

Disconnect battery pack from tool or place the switch in the locked-off position before making any assembly, adjustments or changing accessories. Such preventive safety measures reduce the risk of starting the tool accidentally.

Inserting and Releasing Battery Pack

Slide charged Battery Pack (Fig. 2, 11) into the housing until the battery pack locks into position.
Your tool is equipped with a secondary locking latch to prevent the battery pack from completely falling out of the tool housing, should it become loose due to vibration.
To remove the Battery Pack (11), press the Battery Pack Release Button (10) and slide the battery pack forward.
Press the Battery Pack Release Button (10) again and slide the battery pack completely out of tool housing.

Installing SDS-max® Accessories

Clean the insert shank end of the accessory to remove any debris, then lightly grease with a light oil or lubricant.
Pull and hold Locking Sleeve (Fig. 3, 2) backward. Insert accessory into the tool holder through the Dust Shield (1), while twisting and pushing inward until it sets into place. Release locking sleeve to lock bit in place. Pull outward on the accessory to be certain it is locked into the tool holder.
Note: The high efficiency available from the rotary hammers can only be obtained if sharp and undamaged accessories are used. The “cost” to maintain sharp and undamaged accessories is more than offset by the “time saved” in operating the tool with sharp accessories.

Removing SDS-max® Accessories

Accessories may be hot after use. Avoid contact with skin and use proper protective gloves or cloth to remove.
To remove an accessory, pull accessory Locking Sleeve (Fig. 4, 2) backward and pull bit forward.

All accessories should be wiped clean after re- Fig. 5 moving.

Auxiliary Handle

The tool must be used with the Auxiliary Handle (Fig. 5, 14), which can be swiveled 360°.
To reposition and/or swivel the Auxiliary Handle (14), loosen the hand grip, move the handle to the desired position along the barrel and securely retighten the hand grip.

Connectivity Module Installation (sold separately)

⚠ To reduce the risk of injury read the operating instructions included with Bosch connectivity module. Operating instructions for connectivity module include important information not covered in this manual.
If connectivity module is not purchased with the tool, or if the replacement of the module or the battery becomes necessary, please follow this procedure (See Fig. 6):

• Using a flat screwdriver or a coin, remove the cover A from the side of the handle, by turning it 1/8 turn counter-clockwise (Fig. 6 or 7).
• If the tool is already equipped with the connectivity module, remove the battery B, but do not remove the connectivity module C.
• If the connectivity module is installed for the first time, remove the plastic placeholder D from the connectivity module compartment, and place the connectivity module C in the compartment observing correct orientation (Fig. 7). Note: Store the placeholder D in a safe place. Reinsert the placeholder again if the communications module is removed.
• Next place new battery B on the top of the connectivity module with the “+” polarity facing up (Fig. 6).
• Place the cover A over the battery and turn it 1/8-turn clockwise to lock using a flat screwdriver or a coin.

Operation

⚠ Disconnect battery pack from tool or place the switch in the locked-off position before making any assembly, adjustments or changing accessories. Such preventive safety measures reduce the risk of starting the tool accidentally.

Variable Speed Controlled Trigger Switch

Your tool is equipped with a Variable Speed Trigger Switch (Fig.8, 8). The tool can be turned “ON” or “OFF” by squeezing or releasing the trigger. The speed can be adjusted from the minimum to maximum nameplate RPM by the pressure you apply to the trigger. Apply more pressure to increase the speed and release pressure to decrease speed.

⚠ To reduce the risk of injury immediately discontinue use of the tool if the variable speed control ceases to function. Subsequent loss of on/off control of the trigger switch is likely.

Lock-On / Lock-Off Button

Lock-On / Lock-Off Button (Fig.8, 6) serves two purposes:

• Lock-on function to keep the tool running without constantly depressing the switch (8). This function works only when the Mode Selector Dial (4) is in the “Hammering” mode (See “Mode Selector Dial” chapter).
• Lock-Off function to prevent an accidental activation of the switch (8). When the button is in down position, the trigger is disabled. Before turning the tool on, press and release the button (6) to return it to the up (unlocked) position.

⚠ Pressing the lock-on / lock off button while the tool is running in any mode other than “Hammering” will shut the tool off and lock it in an “OFF” position. In addition, switching modes while in lock-on mode will shut the tool off and lock it in an “OFF” position.
To resume hammer operation, press and release the Lock-Off Button (6).

Mode Selector Dial

“Vario-Lock”

The Vario-Lock position is intended for use with chiseling bits such as bull points, spades, gouges, etc. Choose a position which is best suited for your operation.
Turn the Mode Selector Dial (Fig. 10, 4), to the “vario-lock” setting. Next, rotate the locking sleeve, along with the accessory, to the desired position. Then turn the mode selector dial to the “Hammering” setting and slightly turn the locking sleeve to have it automatically lock into a definite position.

User Interface

The User Interface (Fig. 11, 9) is used to select 15 the work preset and to indicate the status of the power tool and battery.

POWER TOOL STATUS FRAME

Green light of the power tool status frame (Fig. 17 11, 15) indicates that everything is functioning as intended.

Yellow light indicates that:

• Critical temperature has been reached (the Temperature Indicator (16) is also glowing 21 yellow) or
• Battery is almost empty (the Battery Charge Indicator (18) is also glowing yellow).

Steady red light indicates that:

• Power tool is overheated (the Temperature Indicator (16) is glowing red) or

• Battery is depleted (the Battery Charge Indicator (18) is also glowing red).

• An attempt has been made to press Lock-on Button (6) while the tool was running in any mode other than “Hammering” (See “Lock-On / Lock-Off Button” chapter.
  Flashing red light indicates that:

• Kickback Control is triggered (the Kickback Control Indicator (19) is also flashing) or

• Flashing blue light indicates that the power tool is connected to a mobile device or settings are being transferred. To accept the change of settings from the mobile device press Work Preset Button (21).

BATTERY CHARGE INDICATOR
When the Battery Charge Indicator (Fig. 11, 18) is glowing green, the battery is charged and the number of bars shows the percentage level of the charge.

Glowing yellow and only one bar indicates that the battery needs to be charged or replaced soon.

TEMPERATURE INDICATOR
If the Temperature Indicator (Fig. 11, 16) is glowing yellow, the critical temperature of the motor, electronics or battery has been reached.

Run the power tool at no load and allow it to cool down.

If the temperature indicator is glowing red, power tool is overheated and will switch off. Allow the power tool to cool down.

SMARTPHONE STATUS SYMBOL
If Kickback control symbol (Fig. 11, 19) is flashing, Kickback Control has been triggered.

WORK PRESETS
The Work Preset Button (Fig. 11, 21) allows you switch between work presets:

In Auto work preset, the power tool reaches maximum performance.

• For “Drilling” operating mode: Rapid increase in speed for controlled drilling up to maximum RPM. Kickback control is enabled.

• For “Hammering” operating mode: Rapid increase in speed up to maximum BPM when chiseling is started.
  Soft work preset is used to work with delicate materials.

• For “Drilling” operating mode: Slow increase in speed for controlled drilling. Kickback control is enabled.

• For “Hammering” operating mode: Soft start is enabled for precise control and positioning with a variable speed control in the trigger.

In Favorite work preset, the power tool can be customized via `Bosch Toolbox’ app.

• For “Drilling” operating mode: Ramp-up speed and maximum RPM can be customized. The sensitivity of Kickback Control can be configured.
• For “Hammering” mode: Soft start can be enabled/disabled.
  Refer to “Using `Bosch Toolbox’ app” chapter for more information.

Adaptive Speed Control

In “Hammering” operating mode, the power tool starts at a low idle speed for better control and precise positioning. When force is applied to the workpiece, the speed quickly increases.

Slip Clutch

The tool has an internal pre-set slip clutch. The output spindle will stop rotating if the accessory binds and overloads the tool.

Vibration damping

The integrated vibration damping function reduces the generated

Do not use the power tool if the vibration damper (Fig. 1, 5) is damaged.

Kickback Control

The rapid shut-off feature enables better control and improves user’s comfort. The power tool automatically shuts off in case of sudden and unexpected rotation of the power tool around the drilling axis (for example jamming of the drill bit in reinforcing steel or wedging application tool). To restart the power tool, release the trigger switch and then actuate again.
Kickback Control can activate only when the power tool is running at maximum operating speed and can rotate freely around the drill bit axis.

Tool Tips

For the best penetration rates in concrete, run the tool with a steady pressure, but do not use excessive force as this will decrease the efficiency of the tool.

All hammers require a short period of time to warm up. Depending on the room temperature, this time may vary from approximately 15 seconds (90°F / 32°C) to 2 minutes (32°F / 0°C). A new hammer requires a break-in period before full performance is realized. This period may require up to 5 hours of operation.

A combination hammer is likely to be the most expensive portable tool at the construction job. The long wear and efficient operation of the Bosch hammers will more than justify the cost for tools of this type. As earlier pointed out, sharp accessories as well as clean air vents are necessary for efficient operation. Establish and follow a set maintenance program.

Connectivity

Using `Bosch Tool Box’ app

Install Bosch Toolbox’ app on your mobile device or make sure you are running the latest version of the app. LaunchBosch Tool Box’ app on your mobile device and click on “My Tools” icon/tile. Follow the app directions to pair the tool with the mobile device.
After pairing your tool with a mobile device you can adjust certain functions or check the status of the power tool using Bosch Toolbox app.
Every time you change any setting, the tool will confirm the changes by flashing blue light of the power tool status frame (Fig. 11, 15).

• A. Help button ­ tapping this button will bring up help screen.

• B. Tool photo ­ tapping on the photo will let you customize the photograph of the tool.

• C. Power tool battery charge status ­ the number of green `batteries’ indicates the estimated charge level for the battery pack.

• D. Power tool nickname ­ tapping on the `pencil’ icon will let you customize the tool nickname. You can also do it when changing the tool photo.

• E. Connection status bar ­ Here you can see the connection (signal) strength indicated by vertical bars. You can use toggle switch to disconnect the tool from your mobile device.

• F. Favorite Preset Adjustment ­ Select the Favorite Preset in the user interface on the tool to use the settings configured in this section. The Favorite Preset offers settings for drilling and for hammering.

• G. Work Light ­ Modify settings to the LED.

• H. User Interface ­ Customize tool interface and usage settings.

• I. Reset to Factory Default ­ returns the tool to its original settings.

• J. Tool alerts ­ tapping the `alerts triangle’ will display any alerts received from the tool.

• K. Info button ­ displays tool information and specifications.

Dust Extraction

For selection of dust collection systems and operating instructions, see the Operating / Safety Instructions for `Dust Extraction Attachments for Hammers and Hammer Drills’ included with your tool or with the dust extraction attachment.

Maintenance

⚠ To avoid accidents, always disconnect the battery pack from tool before servicing or cleaning.

Service

⚠ NO USER SERVICEABLE PARTS INSIDE. Preventive maintenance performed by unauthorized personnel may result in misplacing of internal wires and components which could cause serious hazard. We recommend that all tool service be performed by a Bosch Factory Service Center or Authorized Bosch Service Station.

Batteries

Be alert for battery packs that are nearing their end of life. If you notice decreased tool performance or significantly shorter running time between charges then it is time to replace the battery pack. Failure to do so can cause the tool to operate improperly or damage the charger.

Tool Lubrication

Your Bosch tool has been properly lubricated and is ready for use.

Motors

The motor in your tool has been engineered for many hours of dependable service. To maintain peak efficiency of the motor, we recommend it be examined every six months. Only a genuine Bosch replacement motor specially designed for your tool should be used.

Cleaning

⚠ Certain cleaning agents and solvents damage plastic parts. Some of these are: gasoline, carbon tetrachloride, chlorinated cleaning solvents, ammonia and household detergents that contain ammonia.
Ventilation openings and switch levers must be kept clean and free of foreign matter. Do not attempt to clean by inserting pointed objects through opening.

Accessory Storage & Maintenance

Store accessories in a cool dry place and avoid freezing. Before use check accessory for cracks and fractures, do not use if damage is suspected.

Accessories

Do not use attachments/accessories other than those specified by Bosch. Use of attachments/accessories not specified for use with the tool described in this manual may result in damage to tool, property damage, and or personal injury.

Standard equipment ­ 360° Auxiliary Handle

Optional accessories and attachments ­ Connectivity module

Licenses

Copyright (C) 2016­2019 STMicroelectronics All rights reserved.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:
– Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
– Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
– Neither the name of the copyright holders nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission.

THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

Copyright (C) 2009­2016 ARM LIMITED All rights reserved.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:
– Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
– Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
– Neither the name of ARM nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission.

THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

Notes

This page was intentionally left blank

LIMITED WARRANTY OF BOSCH PORTABLE AND BENCHTOP POWER TOOLS
Robert Bosch Tool Corporation (“Seller”) warrants to the original purchaser only, that all BOSCH portable and benchtop power tools will be free from defects in material or workmanship for a period of one year from date of purchase. SELLER’S SOLE OBLIGATION AND YOUR EXCLUSIVE REMEDY under this Limited Warranty and, to the extent permitted by law, any warranty or condition implied by law, shall be the repair or replacement of parts, without charge, which are defective in material or workmanship and which have not been misused, carelessly handled, or misrepaired by persons other than Seller or Authorized Service Station. To make a claim under this Limited Warranty, you must return the complete portable or benchtop power tool product, transportation prepaid, to any BOSCH Factory Service Center or Authorized Service Station. For Authorized BOSCH Power Tool Service Stations, please refer to your phone directory.

THIS LIMITED WARRANTY DOES NOT APPLY TO ACCESSORY ITEMS SUCH AS CIRCULAR SAW BLADES, DRILL BITS, ROUTER BITS, JIGSAW BLADES, SANDING BELTS, GRINDING WHEELS AND OTHER RELATED ITEMS. ANY IMPLIED WARRANTIES SHALL BE LIMITED IN DURATION TO ONE YEAR FROM DATE OF PURCHASE. SOME STATES IN THE U.S., SOME CANADIAN PROVINCES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU. IN NO EVENT SHALL SELLER BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES (INCLUDING BUT NOT LIMITED TO LIABILITY FOR LOSS OF PROFITS) ARISING FROM THE SALE OR USE OF THIS PRODUCT. SOME STATES IN THE U.S. AND SOME CANADIAN PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENT

© Robert Bosch Tool Corporation 1800 W. Central Road Mt. Prospect, IL 60056-2230
Exportado por: Robert Bosch Tool Corporation Mt. Prospect, IL 60056-2230, E.U.A.
Importado en México por: Robert Bosch, S.A. de C.V., Calle Robert Bosch No. 405, Zona Industrial,
Toluca, Edo. de México, C.P. 50070, Tel. (722) 2792300

References

• Bosch Power Tools | Boschtools

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>