OLIGHT BALDR RL 1120 Lumens LED Rail User Manual
- June 9, 2024
- OLIGHT
Table of Contents
BALDR RL 1120 Lumens LED Rail
User Manual
Thank you for purchasing this Olight Product. Please read this manual carefully before use and keep it for future reference!
OPERATION
THREE LIGHT SETTINGS AVAILABLE: As the mark shows, push the setting
switch from left, middle, right to select red beam only, white LED/red beam
combined, white LED only accordingly.
The ambidextrous switch on the BALDR RL Mini can only be pressed down to
activate the light. Pressing the side or front of the switch will not turn it
on.
Momentary ON: Press and hold down either switch for momentary on. The
light will stay on until the switch is released.
On/Off: Single click either switch for constant on. Single click again to
turn the light off.
IN THE BOX
| BALDR RL Mini ( With Battery )
---|---
| USB Magnetic
Charging Cable
| Allen Wrench
| Adapter and Screws
| Oval Point Set Screw
| Cone Point Set Screw
| Socket Screws
SPECIFICATIONS
RED BEAM OFF
RED BEAM ON
- The red beam level is Class 3R, obeying the standard IEC60825-1 requirement.
- All above specifications are test results based on ANSI/NEMA FL1 Standard. The tests are performed when the built-in battery is fully charged.
PRODUCT OVERVIEW
BEFORE FIRST USE
- The low battery indicator will turn red when the light is working and the battery level is less than 10%.
- Connect the USB end of the charging cable to an external USB power source, then attach the other end of the magnetic charging cable to the charging port of the light. It takes no more than 1 hour to fully charge the light ( For reference only. When the USB power supply is insufficient to provide 5V 0.35A power capacity, the charging time will be longer ).
- Before first use please fully charge the product.
LIGHT INSTALLATION
- Pull open the swing arm.
- Slide the rail mount to your desired position.
- Use the included Allen wrench to ensure that the two socket screws are tight. (Two backup socket screws are included)
- Position the Glock rail adapter (already installed) or Pica tinny rail adapter (to be installed first) to the desired rail notch and then close the swing arm.
| ICON | LIGHT SETTING |
|---|---|
| LIGHT | |
| LIGHT&RED BEAM | |
| RED BEAM |
COMPATIBILITY CHECK:
The BALDR RL Mini can be used on most Glock or Pica tinny (mil-std-1913) type
rails. The Glock adapter labeled “GL” is already installed and a Pica tinny
(mil-std-1913) adapter is included in the package. To install the light on
Pica tinny (mil-std-1913) rails, the user needs to replace the “GL” adapter
with the included 1913 adapter using the screws and wrench provided in the
package.
RED BEAM CALIBRATION:
Use the included Allen wrench to rotate the adjustment screws on the side of
the light to calibrate the vertical or horizontal angle of the red beam, and
finally sight in the red beam for accurate use.
NOTE: A backup set of NYLOK adjustable screws is included.
- The NYLOK cone point set screw is used for vertical angle calibration.
- The NYLOK oval point set screw is used for horizontal angle calibration.
DANGER
- DO NOT shine the light directly into human eyes. This may cause temporary blindness, or permanent damage to the eyes.
- DO NOT charge this product with other charging cables except the one included in the original package.
- DO NOT cover the light head, or place the light head down on the ground when the light is on. The radiation energy of the light may cause damage to the light itself, or even result in burning to other materials.
- DO NOT leave the light in any type of fabric bag or fusible plastic container under high temperature.
WARNING
- Keep out of reach of children.
- Red beam light is bright and blinding – DO NOT shine at aircraft or vehicles at any distance.
- If the light is stored for a long time or transported, please turn the light setting switch to the Red Beam Only position.
NOTICE
- The setting switch is magnetically sensitive, when close to magnet, interference may occur.
- Fully charge the battery before storing the light for a long period of time.
- Please keep the charging port clean. Wipe any dust off before charging.
- Please wipe the lens regularly. If the red beam spot is abnormal, please wipe and clean the lens.
- The LED light will work for one minute at the top output mode and gradually step down to 100 lumens within 2 minutes.
- The two switches can only be activated by pushing downward. Pushing forward or on the side of the switch will not activate the light.
- Always attach the light on the rail could better protect the switch and avoid damage caused by falling.
- The BALDR RL Mini can only be charged with the included MCC special charging cable, not compatible with other MCC cables.
- NYLOK is a registered trademark of NYLOK LLC.
EU-Declaration of Conformity can be found here:
https://olightworld.com/ec-declaration
USA Customer Support
cs@olightstore.com
Global Customer Support
customer-service@olightworld.com
Visit www.olightworld.com to see our complete
product line of portable illumination tools.
WARRANTY
Within 30 days of purchase: Contact the original seller for repair or
replacement.
Within 2 years of purchase: Contact Olight for repair or replacement.
This warranty does not cover normal wear and tear, modifications, misuse,
disintegrations, negligence, accidents, improper maintenance, or repair by
anyone other than an authorized retailer or Olight itself.
Dongguan Olight E-Commerce Technology Co., Ltd
Address: 4th Floor, Building 4, Kegu Industrial
Park, No 6 Zhongnan Road, Changan Town,
Dongguan City, Guangdong, China.
Made in China
Documents / Resources
|
OLIGHT BALDR RL 1120 Lumens LED
Rail
[pdf] User Manual
BALDR RL 1120 Lumens LED Rail, BALDR RL 1120, Lumens LED Rail, LED Rail
---|---
References
- Olight | Illuminate Your World.
- Flashlights, Tactical Light, Outdoor Tools - Olight Official Store- Olight
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>