JOY FACTORY axtion bold MP Rugged and Waterproof Case Installation Guide
- June 9, 2024
- JOY Factory
Table of Contents
JOY FACTORY axtion bold MP Rugged and Waterproof Case
Installation Guide
Removal
Remove silicone cover from the hard frame starting at one corner.
Installation
- Insert iPad into hard frame.
- Insert the corner of the hard frame nearest the camera into the silicone cover.
- Insert the rest of the hard frame into the silicone cover.
- Insert each silicone tab tightly into its corresponding slot in the hard frame to ensure the case is water-resistant.
Cleaning Instruction
We recommend cleaning the case after every use cycle. Most hospital-grade disinfectantwipes with high alcohol concentrate are safe to use on the aXtion Bold case. A few that we recommend are:
- Sani-Cloth AF3
- Cavi-Wipes
- Clorox Healthcare Bleach Germicidal Wipes
- Oxivir TB
Follow these steps:
- Clean the back cover with a hospital-grade wipe, using a small stroking motion. Pay special attention to the crevices.
- Use a new hospital-grade wipe to clean the front cover and screen protector.
- Let the case air dry before using.
Internal cleaning may be done as needed following these steps
- Remove the tablet from the case and set aside.
- Clean the inside back cover with a hospital-grade wipe, using a small stroking motion. Pay special attention to the crevices.
- Use a new hospital-grade wipe to clean the inside front cover and screen protector.
- Let the case air dry before putting the tablet into the case.
- Hospital-grade disinfectant wipes may have more detailed instructions for use. Please refer to the manufacturer’s instructions.
- These instructions are only for cleaning cases by The Joy Factory. To clean the tablet, please refer to the manufacturer’s instructions.
Security Cable Slot Installation Guide
- Align the plastic template onto the back of the device ensuring the back camera opening aligns correctly with the tablet.
- Using the included alcohol pad clean the surface of the device where the locking plate will install. The VHB adhesive adheres to the tablet properly when the surface is clean and dry.
- Apply the locking plate onto the tablet. Use an object to apply pressure and allow the adhesive to cure for 48 hours. Then remove the plastic template.
- Install the tablet into the case by first installing the tablet into the plastic frame ensuring the raised camera is inserted UNDER the camera lens. Then, install the plastic frame and tablet into the silicone cover (reference the case
- Security cable
- Insert the security cable into the security cable slot
DISCLAIMER for aXtion Bold Military Grade Certified Cases
Congratulations on the purchase of your new aXtion Bold case from The Joy Factory Inc! BEFORE USE READ ALL INSTRUCTIONS CAREFULLY. IMPROPER USE OF THE CASE COULD RESULT IN DAMAGE TO YOUR DEVICE. This aXtion Bold case is designed only for the device type listed on the box. Thus it is only intended for and only warrantied for proper use with that specific tablet and not for use with another device type. Because different generations of tablets have different specifications, please refer to the packaging for your aXtion Bold case to determine whether your tablet will be compatible with the case you have purchased. If you are not certain whether the device you intend to use with the aXtion Bold case is compatible with the tablet model you have, please contact the company from which you purchased the device or the manufacturer of the device to determine whether it is a model supported by this aXtion Bold case. If the aXtion Bold case is damaged or not functioning properly for any reason; immediately stop use. The Joy Factory expressly disclaims all liability and all warranties, whether expressed or implied, for use of an aXtion Bold case that has been damaged for any reason. The case is covered under our one year manufacturing warranty and can be replaced free of charge for any manufacturing defects. If you believe the case has a manufacturing defect, cease use immediately and contact The Joy Factory by email at support@thejoyfactory.com or by telephone at 949-216-8888, Monday through Friday, 9:00 a.m. to 5:00 p.m., Pacific Standard Time. The Joy Factory will not replace an aXtion Bold case that is damaged, other than one with a manufacturing defect, The Joy Factory is not liable to replace or pay for replacement of your device or any additional items which may be damaged from use of a case with manufacturing defects. The Joy Factory disclaims all liability for lost aXtion Bold cases and any device stored in a lost case. Do not use your aXtion Bold case with any other case or bumper. Use of an additional case or bumper will hinder the military grade certification, and The Joy Factory disclaims all liability from such use and will void any and all warranties, expressed or implied. Any alteration to your aXtion Bold case will void any and all warranties and guarantees, whether expressed or implied, and The Joy Factory disclaims any and all liability for damages arising from use of an altered aXtion Bold case.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>