PREVUE HENDRYX 58503 Ferret Stack Three Story Instruction Manual
- June 9, 2024
- Prevue Hendryx
Table of Contents
58503 Ferret Stack Three Story
Instruction Manual
58503 Ferret Stack Three Story
Instructions online at www.prevuepet.com
CUSTOMER SUPPORT
Please contact Prevue Pet Products:
PHONE: 1 312-243-3624
ONLINE: www.prevuepet.com
EMAIL: customerservice@prevuepet.com
KEY:
L = Left Side
B = Back
F = Front
R = Right Side
CR = Center/Roof
CM = Center/ MidLevel Floor
CG = Center/ Floor Grille
CT = Center/Tray
CS = Center/Shelf
⁕ These pieces are interchangeable:
L 1 = R 1
CM 1 = CM 2
L 2, 3, 4
R 2, 3, 4
are all the sameNO ADDITIONAL TOOLS REQUIRED • For best
results, follow the Assembly Steps in the order presented.
HOW TO TELL THE DIFFERENCE : Several parts and panels may look similar.
Here’s how to tell the difference:
CENTER PANELS
The roof panel (CR) has an attached sliding door on top, and a screw hole on
both ends of the frame.
Both midlevel floor panels (CM) have a detachable wire divider door, and a
screw hole on both ends of the frame.
The ground floor grille panel (CG) has NO door and NO screw hole on the ends.
The shelf (CS) is longer, and has threaded screw holes on the front and back
corners of the frame. FRONT & BACK PANELS :
TOP vs OTHERS
The lower panels (F2, F3, B2, B3) have top corner brackets. Top panels (F4,
B4) do not.
- PIECES
Orient the front legs (F1) with the windbell lock facing forward.
The extended portion of the tray channel rail (L1) dovetails into the inside
of the frame leg. Attach frames together with a hex screw through the bottom
hole.Orient the backstop on the back legs (B1)
facing the back. Attach legs to sides with hex screws in the bottom holes.
Attach the shelf (CS).
Turn the unit over. Fully insert a
caster in each leg. Flip the unit upright. Set the floor grille (CG) in
place.
Stand the side panel (L2) and the lower
back panel (B2) (with corner brackets) in position and attach together with a
hex screw at the top and bottom corners.
⁕ Hand-tighten screws so they remain loose. This will ease the assembly of the
additional levels. Continue adding and attaching panels [side panel (R2),
front panel (F2)], with hand-tightened hex screws as detailed above. Place one
of the midlevel floors (CM1, or CM2 – with the removeable divider door) in
place and secure it with hex screws, one screw on each end.Repeat the assembly of Step 3 with the duplicate panels: front &
back panels (F3, B3 —with brackets) and side panels (L3, R3). Attach together
with hex screws in the top and bottom corners.
Place the midlevel
floor (CM – with divider door) in place and secure it with hex screws, one on
each end.
Repeat the assembly method from Steps 3 &
4:
The remaining front & back panels (F4, B4) will not have brackets in the upper
corners.
Add and attach front, back, and side panels (R4, L4) as before, with
handtightened hex screws at the top and bottom corners. Place the roof (CR – with the non-removable sliding door) in
position and attach with a hex screw on each end. ⁕ Tighten the screws over
the entire cage with the hex key until all screws are snug.
Hook a ramp onto the platform and positioned at the cage-front end.
Place the platform/ramp in the lower level, on the middle horizontal wire.
Remove the divider door. Hook a ramp on the wire loops, and rest the other end
on the platform below. NOTE: The divider may be reattached with the ramp
installed.
Install the remaining platforms and ramps in the same manner.
Add the hammock.
Rotate the windbell lock up and slide the tray into place.
58503—06/22 — A4.4
For more wonderful cages, toys, and accessories for cats, birds, chickens,
rabbits, ferrets, dogs and small animals, visit
www.prevuepet.com
Made in China for Prevue Pet Products, Inc.,
224 N Maplewood Ave,
Chicago IL 60612 USA
1 [312] 243-3624
www.prevuepet.com
customerservice@prevuepet.com
References
- Prevue Pet Products - Bird Cages, Dog Cages & Pet Supplies
- Prevue Pet Products - Bird Cages, Dog Cages & Pet Supplies
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>