Lilitab LLC CC2564 Bluetooth HCI Module User Manual
- June 15, 2024
- Lilitab LLC
Table of Contents
LLC CC2564 Bluetooth HCI Module
User Manual
Peripheral interface highlight
Power Source: A single host power supply can be used (including VBAT
ranging from 3.0V to 4.8V) for CC2654 module and external VDD18 to 1.8V
supplies for GPIO by host power. Power topology is shown as below figure.
Bluetooth UART:
External patches may be downloaded from the host to the CC2654 through the
UART transports and connection interface is shown in above reference design
circuitry. Support adjustable baud rates from 9600bps to 4Mbps.
Flow control hardware interface is obtained by the following.
- BT debug pin: The debug interface (TX_DBG) helps customers to debug the HW/SW issues for their application.
- Bluetooth PCM: The PCM Interface on the CC2654 can connect to linear PCM Codec devices in master or slave mode. In master mode, the CC2654 generates the PCM_CLK and PCM_SYNC signals, and in slave mode, these signals are provided by another master on the PCM interface and are inputs to the CC2654.
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the
party responsible for compliance could void the user’s authority to operate
this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body.
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
This device is intended only for OEM integrators under the following
conditions:
- The transmitter module may not be co-located with any other transmitter or
antenna,
As long as 1 condition above is met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed
End Product Labeling
The final end product must be labeled in a visible area with the following: “Contains FCC ID: 2A8XU-CC2564”.
Manual Information to the End User
The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module.
The end user manual shall include all required regulatory information/warning as show in this manual
Industry Canada statement
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:
- this device may not cause interference, and
- this device must accept any interference, including interference that may cause undesired operation of the device.
Radiation Exposure Statement:
The product comply with the Canada portable RF exposure limit set forth for an
uncontrolled environment and are safe for intended operation as described in
this manual.
The further RF exposure reduction can be achieved if the product can be kept
as far as possible from the user body or set the device to lower output power
if such function is available.
This device is intended only for OEM integrators under the following
conditions:
- The transmitter module may not be co-located with any other transmitter or antenna.
As long as 1 condition above are met, further transmitter test will not be
required. However, the OEM integrator is still responsible for testing their
end-product for any additional compliance requirements required with this
module installed.
End Product Labeling
The final end product must be labeled in a visible area with the following:
“Contains FCC ID: 2A8XU-CC2564”.
Manual Information to the End User
The OEM integrator has to be aware not to provide information to the end user
regarding how to install or remove this RF module in the user’s manual of the
end product which integrates this module.
The end user manual shall include all required regulatory information/warning
as show in this manual
Industry Canada statement
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions:
- this device may not cause interference, and
- this device must accept any interference, including interference that may cause undesired operation of the device.
Radiation Exposure Statement:
The product comply with the Canada portable RF exposure limit set forth for an
uncontrolled environment and are safe for intended operation as described in
this manual.
The further RF exposure reduction can be achieved if the product can be kept
as far as possible from the user body or set the device to lower output power
if such function is available.
This device is intended only for OEM integrators under the following
conditions:
- The transmitter module may not be co-located with any other transmitter or antenna.
As long as 1 condition above are met, further transmitter test will not be
required. However, the OEM integrator is still responsible for testing their
end-product for any additional compliance requirements required with this
module installed.
End Product Labeling
The final end product must be labeled in a visible area with the following:
“Contains IC: 29503-CC2564”.
Manual Information to the End User
The OEM integrator has to be aware not to provide information to the end
user regarding how to install or remove this RF module in the user’s manual of
the end product which integrates this module.
The end user manual shall include all required regulatory information/warning
as show in this manual.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>