milwaukee M18 FROP15 18V Li-Ion RedLithium Brushless Cordless Polisher Instruction Manual

: June 9, 2024
: Milwaukee

Table of Contents

Product Overview
Battery Installation
Instructions
SPECIFIED CONDITIONS OF USE
WORKING INSTRUCTIONS
CLEANING
MAINTENANCE
SYMBOLS
EC DECLARATION OF CONFORMITY
Support
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

milwaukee M18 FROP15 18V Li-Ion RedLithium Brushless Cordless Polisher Instruction Manual

Product Overview

Battery Installation

Remove the battery pack before starting any work on the machine.
Battery Installation

Instructions

TECHNICAL DATA	M18 FROP15	M18 FROP21
Type	Polisher	Polisher
Production code	4838 77 01 XXXXXX MJJJJ	4911 31 01 XXXXXX MJJJJ
Battery voltage	18 V =	18 V ,
Rated speed	0 – 5100 min-1	0 – 4500 min-1
No-load speed	2650 – 5100 min-‘	2400 – 4500 min-1
Polishing backing pad Diameter	125 mm	150 mm
Polishing pad Diameter max.	125 mm	150 mm
Orbital travel diameter	15 mm	21 mm
Weight according EPTA-Procedure 01/2014 (Li-Ion 2,0 Ah … 12,0 Ah)	2,9 … 4,0
kg	3,0 … 4,2 kg
Recommended Ambient Operating Temperature	-18 … +50 °C
Recommended battery types	M18B…; M18HB…
Recommended charger	M12-18…; M1418C6

Noise information: Measured values determined according to EN 62841.
Typically, the A-weighted noise levels of the tool are:
Sound pressure level / Uncertainty K Sound power level / Uncertainty K Wear ear protectors!| 78,0 dB (A) / 3 dB (A)
89,0 dB (A) / 3 dB (A)| 77,0 dB (A) / 3 dB (A) 88,0 dB (A) / 3 dB (A)

WARNING!
The vibration and noise emission level given in this information sheet has been measured in accordance with a standardized test given in EN 62841 and may be used to compare one tool with another. It may be used for a preliminary assessment of exposure.
The declared vibration and noise emission level represents the main applications of the tool. However if the tool is used for different applications, with different accessories or poorly maintained, the vibration and noise emission may differ. This may significantly increase the exposure level over the total working period.
An estimation of the level of exposure to vibration and noise should also take into account the times when the tool is switched off or when it is running but not actually doing the job. This may significantly reduce the exposure level over the total working period. Identify additional safety measures to protect the operator from the effects of vibration and/or noise such as: maintain the tool and the accessories, keep the hands warm, organization of work patterns.

WARNING! Read all safety warnings, instructions, illustrations and specifications provided with this power tool. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference

ADDITIONAL SAFETY AND WORKING INSTRUCTIONS

Never reach into the danger area of the machine when it is running. Chips and splinters must not be removed while the machine is running.
Immediately switch off the machine in case of considerable vibrations or if other malfunctions occur. Check the machine in order to find out the cause.
The workpiece must be fixed if it is not heavy enough to be steady.
Do not let any metal parts enter the airing slots – danger of short circuit!

WARNING! To reduce the risk of fire, personal injury, and product damage due to a short circuit, never immerse your tool, battery pack or charger in fluid or allow a fluid to flow inside them. Corrosive or conductive fluids, such as seawater, certain industrial chemicals, and bleach or bleach containing products, etc., Can cause a short circuit.
Never break open battery packs and chargers and store only in dry rooms. Keep dry at all times.
Use only System M18 chargers for charging System M18 battery packs. Do not use battery packs from other systems.

SPECIFIED CONDITIONS OF USE

The polisher can be used for polishing lacquers, coatings, plastics and other smooth surfaces.
Do not use the product in any way other than those stated for intended use.

RESIDUAL RISK

Even when the product is used as prescribed, it is still impossible to completely eliminate certain residual risk factors. The following hazards may arise in use and the operator should pay special attention to avoid the following:

Injury caused by vibration. Hold the product by designated handles and restrict working time and exposure.
Exposure to noise can cause hearing injury. Wear ear protection and limit exposure.
Injury due to flying debris. Wear eye protection, heavy long trousers, gloves and substancial footwear at all times.
Inhalation of toxic dusts.

NOTES FOR LI-ION BATTERIES

Use of Li-Ion batteries
Battery packs which have not been used for some time should be recharged before use.
Temperatures in excess of 50°C (122°F) reduce the performance of the battery pack. Avoid extended exposure to heat or sunshine (risk of overheating).
The contacts of chargers and battery packs must be kept clean.
For an optimum life-time, the battery packs have to be fully charged, after use.
To obtain the longest possible battery life remove the battery pack from the charger once it is fully charged.
For battery pack storage longer than 30 days:
Store the battery pack where the temperature is below 27°C and away from moisture
Store the battery packs in a 30% – 50% charged condition
Every six months of storage, charge the pack as normal.

Battery protection for Li-Ion batteries
In extremely high torque, binding, stalling and short circuit situations that cause high current draw, the tool will vibrate for about 5 seconds, the fuel gauge will flash,and then the tool will turn OFF.
To reset, release the trigger. Under extreme circumstances, the internal temperature of the battery pack could raise too much. If this happens, the fuel gauge will flash until the battery pack cooled down. After the lights go off, the work may continue.

Transporting Lithium Batteries
Lithium-ion batteries are subject to the Dangerous Goods Legislation requirements.
Transportation of those batteries has to be done in accordance with local, national and international provisions and regulations. The user can transport the batteries by road without further requirements.
Commercial transport of Lithium-Ion batteries by third parties is subject to Dangerous Goods regulations. Transport preparation and transport are exclusively to be carried out by appropriately trained persons and the process has to be accompanied by corresponding experts.

When transporting batteries:
Ensure that battery contact terminals are protected and insulated to prevent short circuit. Ensure that battery pack is secured against movement within packaging. Do not transport batteries that are cracked or leak. Check with forwarding company for further advice.

WORKING INSTRUCTIONS

Always use the handles for proper control. Move the polisher back and forth in long, sweeping strokes. Too much pressure, the wrong angle or improper motion may cause swirl marks or burning. For detailed polishing instructions, read the instructions provided with the finishes, waxes and polishes.

WARNING! To reduce the risk of injury, follow instructions for preventing snagging. Snagging may cause the tool to kick back and the operator to suddenly lose control of the tool. Always use pommel handle to maintain control.

Preventing Snagging
Snagging occurs when polishing pads get caught on rough edges of a work surface. Snagging can cause the tool to suddenly “kick back” and it may cause the pad to burn through the paint. To reduce the risk of snagging, use the polisher at low speeds when polishing rough surfaces. For tricky areas such as near trim or between a mirror and window on a car, do not take chances with a polisher. Polish these surfaces by hand.

CLEANING

The ventilation slots of the machine must be kept clear at all times.

MAINTENANCE

Use only Milwaukee accessories and Milwaukee spare parts. Should components need to be replaced which have not been described, please contact one of our Milwaukee service agents (see our list of guarantee/service addresses).
If needed, an exploded view of the tool can be ordered. Please state the Article No. as well as the machine type printed on the label and order the drawing at your local service agents or directly at: Techtronic Industries GmbH, Max‑Eyth‑Straße 10, 71364 Winnenden, Germany.

SYMBOLS

Please read the instructions carefully before starting the machine.
CAUTION! WARNING! DANGER!
Remove the battery pack before starting any work on the appliance.
Do not use force.
Always wear goggles when using the machine.
Dust Filter
Accessory – Not included in standard equipment, available as an accessory.
Do not dispose electric tools, batteries/rechargeable batteries together with household waste material. Electric tools and batteries that have reached the end of their life must be collected separately and returned to an environmentally compatible recycling facility. Check with your local authority or retailer for recycling advice and collection point.
n0 No-load speed
V Voltage
Direct Current
European Conformity Mark
British Conformity Mark
Ukraine Conformity Mark
EurAsian Conformity Mark

EC DECLARATION OF CONFORMITY

We declare as the manufacturer under our sole responsibility that the product described under “Technical Data” fulfills all the relevant regulations and directives listed below and that the following harmonized standards have been used.