T-DAGGER TGK200 Third Mock Examination Mechanical Keyboard User Manual
- June 9, 2024
- T-DAGGER
Table of Contents
The third mock examination mechanical keyboard
TGK200
TGK200 Third Mock Examination Mechanical Keyboard
-
Taking into account: Wired, 2.4G, Bluetooth three models;
-
Axle lamp specifications: 4228-RGB;
-
Side lamp specifications: 1210-RGB;
-
Axle: KaiHua low shaft hot plug seat;
-
Power source seat specifications: ultra-thin 3PIN, 1.25MM, horizontal welding;
-
The toggle switch is 2 segments:
6.1.Dual-mode state (wired+Bluetooth)
Toggle the switch and push it down: turn off the battery, plug in the data line (wired mode), and turn off the battery when there is no data line; Toggle the switch to push up: turn on the battery and automatically switch into Bluetooth mode FN+Q (default); Bluetooth is divided into three groups: FN+Q, FN+W, FN+E;
6.2.Dual-mode state (wired +2.4G)
Toggle the switch and push it down: turn off the battery, plug in the data line (wired mode), and turn off the battery when there is no data line; Toggle the switch to push up: turn on the battery and automatically switch into the 2.4G mode.
6.3.Three-mode state (wired +2.4G+ Bluetooth)
Toggle the switch and push it down: turn off the battery, plug in the data line (wired mode), and turn off the battery when there is no data line; Toggle the switch to push up: turn on the battery and automatically switch into Bluetooth mode (default FN+Q);Manually switch to Bluetooth and 2.4G modes: FN+Q (Bluetooth), FN+W (Bluetooth), FN+E (Bluetooth), FN+R(2.4G); After FN+T (wired) is switched, the corresponding button lights show: blue (Bluetooth), red (2.4G), and blink slowly for 3 times; Bluetooth name: BT3.0 BT5.0 can be modified -
The weak light is: P key (white light flashes slowly)
-
Number of keys: 68key: all keys are supported without conflict.
-
WinXP,Win7,Win8,Win10, OS X and Linux are supported.
-
Power on again to save the last light effect (power-off memory).
-
Combination Key Fn + Esc= ~
Fn + 1 = F1
Fn + 2 = F2
Fn + 3 = F3
Fn + 4 = F4
Fn + 5 = F5
Fn + 6 = F6
Fn + 7 = F7
Fn + 8 = F8
Fn + 9 = F9
Fn + 0 = F10
Fn + – = F11
Fn + = =F12
Fn + Tab=Return to the keyboard factory mode (press and hold for 3 seconds)
Fn + Adjust the brightness of keypad lights.
FN + Adjust the keypad light speed.
Fn +Win=Win key is locked, and the key light shows that the white light is always on. After unlocking, the original keypad light mode will be restored.
Click the CAPS LOCK key to turn on the size switching function, and the key light will always be on.
After it is turned off, the original keypad light mode will be restored.
FN + CAPS=MAC/WIN
Fn + END=HOM;
Fn + Del=Ins;
Fn + Pg Up=PrtSc;
Fn + Pg Dn =PAUS; -
Fn + [{ Key area light mode cycle switchingX light modes, the default is X.
-
Fn + ]} Keypad light color switching
-
Fn + | : Key light on/off
-
Fn + ;” At the bottom of the light cycle switch, (RGB gallops clockwise-seven-color cycle breathing (red-yellow-green-cyan-pink-white)-red is always on-yellow is always on-green is always on-cyan is always on-blue is always on-pink is always on-white is always on -10 light modes.
-
Fn+ ‘” : Bottom light on/off
-
Lighting pattern:
Constant light mode, breathing mode, dreamy rainbow, hair trigger, walking in the rain, rainbow roulette wheel, ripple spreading, stars, no trace through the snow, Flowing, drifting with the tide, following the shadows, sinusoidal light waves, scanning left and right, rotating windmills, colorful waterfalls, blooming flowers, rotating storms, Back and forth collision. -
Press the key combination Fn + BackSpace, the backlight goes out, and the number keys 1 to 0 light up to show the proportion of electricity, for example:
1, indicating 10% electricity, 1 and 2, indicating 20% electricity. (less than 30% red, less than 50% yellow and more than 50% green). -
Low electrical parameters: In wireless mode, when the battery is detected to be lower than or equal to 3.1V, it will be turned off, and it will be able to resume normal use after being plugged in for charging. Or when the battery is greater than or equal to 3.3V, it can be used normally.
FCC Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures: Reorient or relocate
the receiving antenna. Increase the separation between the equipment and
receiver. Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected. Consult the dealer or an experienced
radio/TV technician for help. Caution: Any changes or modifications to this
device not explicitly approved by manufacturer could void your authority to
operate this equipment. This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
RF Exposure Information
The device has been evaluated to meet general RF exposure requirement. The
device can be used in portable exposure condition without restriction.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>