ADVECO ADplus Water Heaters User Manual

ADVECO ADplus Water Heaters

Adveco ADplus Water Heaters

Tough, floor-standing condensing high capacity water heaters with built-in storage for instantaneous commercial DHW applications

• + Highly efficienct for lower operating costs
• +70 kW, 115kW and 140kW variants
• + Ultra-low carbon and NO, emissions
• +Fast recovery timnes
• +Works in direct contact with soft mains water
• +Long-lasting titanium stainless steel construction Built-in redundancy
• +Compact space-saving, cost-saving design

The New Priority – Reducing Energy Used For DHW

Energy saving legislation and commercial building insulation techniques have significantly reduced heating demands, resulting in greater focus on the need to address fuel consumption and emissions generated by the production of hot water. At the same time the popularity of high performance showers, cascade showers, jacuzzis, wellness and fitness centres, have driven up daily demands for year round hot water within the commercial sector. The extremely efficient Ecologic pre-mix burner enables the ADplus range to achieve ideal combustion efficiency (106% net). Optimised burning reduces the amount of fuel consumed and minimises carbon and NOₓ emissions in the atmosphere. The ADplus range also offers whisper quiet operation (as low as 66dB).

FEATURE & BENEFITS

• High capacity instantaneous production of domestic hot water
• Built-in 120 litre water tank
• Modern, compact floor standing arrangement
• Extremely high quality AISI 316Ti heat exchangers for lasting reliability and efficiency
• Multiple heat engines for improved efficiency and built-in redundancy (ADplus115 & 140)
• High efficiency pre-mix burner provides large modulation range
• High maximum run pressure up to 11 bar
• Low emissions, built with Class 6 technology for NOₓ at 27mg/kWh
• Supports natural gas or LPG
• Acid condensate neutraliser included
• Integrated flue back preventer & non-return valve for overpressure cascade flue systems
• Standard flue systems using low cost 110-160 mm diameter PP
• 20% hydrogen blend compatible

The Adveco ADplus for reliably delivering consistent, low peak, commercial hot water (DHW) demands…

PERFECT FOR REFURBISHMENT PROJECTS
With a floor-standing vertical layout, ADplus water heaters are able to optimise valuable plant room space, delivering high power from a smaller footprint. With just 10cms clearance required between each unit, even large systems remain compact and straightforward to install. Featuring single or dual 70 kW condensing AISI 316Ti (Titanium) stainless steel heat exchangers, ADplus can also be installed in cascade sequence of up to eight units delivering 1120 kW for larger scale commercial projects.

LOWER ENVIRONMENTAL IMPACT
Reduce energy use, costs and emissions from buildings that are already on-gas or off-grid. Ultra-low CO and NOₓ emissions.

FAST RECOVERY TIMES TO MEET CONSTANT DEMANDS
Able to rapidly reload the built-in 120 litre storage tank for fast recovery times. Up to 2534 l/h at ΔT 50°C. ADplus is ideal for DHW applications with low peak demands and high continuous withdrawals, without any problem for small withdrawals, as typically seen in restaurants and canteens

RESISTANT TO MOST MAINS WATER CONDITIONS
ADplus’ titanium primary heat exchangers can be directly supplied by mains water while remaining resistant to aggressive chlorinated waters and corrosive soft water. With a built-in recirculating pump, ADplus not only maximises performance from the heat exchangers, but also protects them from limescale deposition to increase the system’s lifespan

ADplus Key Components

High Quality Manufacture

Multiple heat exchanger in ADplus 115 & 140
By combining two load-balanced heat engines within a single floor standing chassis, ADplus 115 & 140 ensure uniform wear and built-in redundancy as standard.

Continuous non-welded run and large bore, three-pass design
Durable and corrosion resistant titanium-stabilised stainless steel construction provides high-capacity heat transfer, high flow rates, with minimal pressure loss and corrosion resistance. The unique, efficient three- pass design uses large bore, circular cross sections to reduce scale formation.

Five-year heat exchanger and burner warranty
Peace of mind with long-term warranty from failure or manufacturing defect. Includes two year commissioned warranty for all parts and labour.

Optimal Efficiency For Improved Savings

The Ecologic premix burner, manufactured from high performance Fecralloy to deliver at very high temperatures, spreads short and perfectly nourished flames for high-efficiency combustion. This patented system, optimised through a constant air/gas ratio at each point of the turndown range. High efficiency DHW is then maximised by guaranteeing the speed of the inlet water inside the heat exchanger. ADplus achieves this by regulating the correct water flow in accordance with inlet water hardness.

Easy To Install And Maintain

With a floor-standing vertical layout, ADplus water heaters are able to optimise valuable plant room space. Featuring single or dual 70 kW condensing AISI 316Ti Titanium stainless steel heat exchangers, ADplus can be installed in cascade sequence of up to eight units delivering for larger-scale commercial projects which remain compact and straightforward to install.

• Compact size and weight that will fit through a standard 65cm wide door
• Floor standing arrangement with adjustable feet
• No need for an expensive frame
• Full access from the front for easy maintenance
• Pre-wired terminal box for easy electrical connection of sensors, pumps and control boards
• deal for soft water applications. Hard water areas over 150ppm require use of a water softener down to 100ppm.

ADplus in Cascade

Connect and control up to eight ADplus140 units in cascade for 1120 kW

• No framework requirement for immediate cost savings. Connect at a minimum of 10cm to occupy less plant room floor space
• Full temperature control and selfcheck maintenance functions
• Up to 325/min of DHW at Δt 50°C

More Effifficient Control

The ADplus range’s digital back-lit control panel provides intuitive electronic temperature control, water flow monitoring and setting of correct water speed according to hardness. This helps prolong the life of the heat exchanger and efficiency of the system. The control board also displays boiler phases and error messages.

Seamless System Integration
With an optional 885IF interface, control of AD water heater is enabled through 0-10V analog signal, MODBUS digital signal or dedicated interface, that can be integrated to all devices with Lon- Works or BACnet protocol. Perfect for commercial, industrial and apartment systems. ADplus can be configured, monitored and remotely controlled to reduce energy consumption and lower the cost and frequency of maintenance visits.

Control Board Management

• Sanitary circuit pump
• Output modulation
• Monitor water flow in l/min
• Pump unlock system
• Auto diagnostic of all components and functions: visualisation of errors and lockouts, temperature sensors, ionisation current, fan rotation speed, water flow rate and water pressure
• Anti-freeze device
• Low water flow protection
• Low water pressure protection
• Flue blocked pressure switch

Technical Specifificatitions

Connectitions & Dimensions

Connections

Model DHW Supply (1) Cold Water Inlet (2) Air Intake (3) Flue Gas Outlet Exhaust (4) Gas Inlet (5) Condensate Drain (6)

• ADplus70 1 ½” 1 ½” Ø110 mm Ø110 mm 1‘’ Ø28 mm
• ADplus115 1 ½” 1 ½” Ø110 mm Ø110 mm 1‘’ Ø28 mm
• ADplus140 1 ½’’ 1 ½’’ Ø110 mm Ø110 mm 1 ‘’ Ø28 mm

Dimensions

Model H x W x D (mm)

• ADplus70 1815 x 600 x 706
• ADplus115 1815 x 600 x 706
• ADplus140 1815 x 600 x 706

Note fittings and flanges are not factory assembled

Flue Connectitions

External flue size: 110/160 mm PP/SS 160 mm/225 mm PP/SS

• Suitable for: ADplus 70; ADplus 115; ADplus140 ADplus70; ADplus115; ADplus140*
• Requires adaptor: 110-160 mm: 0718025

UNI 11528 legislation allows the connection of two appliances with similar characteristics in the same flue system even if they serve different installations. The ADplus condensing water heater can be combined with an Adveco MD condensing boiler, connecting them in the same flue system. Both appliances can be dimensioned according to real DHW and heating needs with optimised performance and condensing effect.

T | 01252 551 540 E | enquiries@adveco.co

Adveco Ltd. Unit 7 & 8 Armstrong Mall, Southwood Business Park, Farnborough, Hampshire GU14 0NR ADVECO ADPLUS WATER HEATER PRODUCT GUIDE SR200101 www.adveco.co

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>