milwaukee M12 FDD2 Li-Ion RedLithium Brushless Cordless Percussion Drill Instructions

: June 9, 2024
: Milwaukee

Table of Contents

M12 FDD2 Li-Ion RedLithium Brushless Cordless Percussion Drill
TECHNICAL DATA
DRILL SAFETY WARNINGS
ADDITIONAL SAFETY AND WORKING INSTRUCTIONS
SPECIFIED CONDITIONS OF USE
RESIDUAL RISK
NOTES FOR LI-ION BATTERIES
MAINTENANCE
Documents / Resources

Nothing but HEAVY DUTY.®
M12 FDD2 / M12 FPD2
Original instructions

M12 FDD2 Li-Ion RedLithium Brushless Cordless Percussion Drill

Picture section
with operating description and functional description
Text section with Technical Data, important Safety and Working Hints and description of Symbols milwaukee M12 FDD2 Li-Ion RedLithium Brushless
Cordless Percussion Drill - fig 1

TECHNICAL DATA

| M12 FDD2| M12 FPD2
---|---|---
Type| Cordless Drill Driver| Cordless percussion drill/driver
Production code| 4813 24 01 XXXXXX MJJJJ| 4813 37 01 XXXXXX MJJJJ
Voltage battery pack| 12 V | 12 V
No-load speed, 1st gear
No-load speed, 2nd gear| 0-450 min-1
0-1550 min-1| 0-450 min-1
0-1550 min-1
Impact range, 1st gear
Impact range, 2nd gear|

–
–

Noise information:
Measured values determined according to EN 62841.
Typically, the A-weighted noise levels of the tool are:

Sound pressure level / Uncertainty K	74,8 dB(A) / 3 dB(A)	89 dB(A) / 3 dB(A)
Sound power level / Uncertainty K	85,8 dB(A) / 3 dB(A)	100 dB(A) / 3 dB(A)

Always wear ear protectors!
Vibration information: Total vibration values (vector sum in the three axes) determined according to EN 62841.
Vibration emission value ah / Uncertainty K

Percussion drilling into concrete	–	15,73 m/s²/ 1,5m/s²
Drilling into metal	1,92 m/s²/ 1,5m/s²	1,92m/s² / 1,5 m/s²
Screwing	0,86m/s²/ 1,5m/s²	0,86 m/s² / 1,5m/s²

WARNING!
The vibration and noise emission level given in this information sheet has been measured in accordance with a standardized test given in EN 62841 and may be used to compare one tool with another. It may be used for a preliminary assessment of exposure.
The declared vibration and noise emission level represents the main applications of the tool. However if the tool is used for diﬀerent applications, with diﬀerent accessories or poorly maintained, the vibration and noise emission may diﬀer. This may signiﬁcantly increase the exposure level over the total working period.
An estimation of the level of exposure to vibration and noise should also take into account the times when the tool is switched oﬀ or when it is running but not actually doing the job. This may signiﬁcantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from the eﬀects of vibration and/or noise such as: maintain the tool and the accessories, keep the hands warm, organization of work patterns.
WARNING Read all safety warnings, instructions, illustrations and speciﬁcations provided with this power tool. Failure to follow all instructions listed below may result in electric shock, ﬁre and/or serious injury. Save all warnings and instructions for future reference.

DRILL SAFETY WARNINGS

Safety instructions for all operations
Hold the power tool by insulated gripping surfaces, when performing an operation where the cutting accessory or fasteners may contact hidden wiring.
Cutting accessory or fasteners contacting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock.
Wear ear protectors when impact drilling. Exposure to noise can cause hearing loss.
Safety instructions when using long drill bits
Never operate at higher speed than the maximum speed rated of the drill bit. At higher speeds, the bit is likely to bend if allowed to rotate freely without contacting the workpiece, resulting in personal injury.
Always start drilling at low speed and with the bit tip in contact with the workpiece. At higher speeds, the bit is likely to bend if allowed to rotate freely without contacting the workpiece, resulting the personal injury.
Apply pressure only in direct line with the bit and do not apply excessive pressure. Bits can bend causing breakage or loss of control, resulting in personal injury.

ADDITIONAL SAFETY AND WORKING INSTRUCTIONS

Use protective equipment. Always wear safety glasses when working with the machine. The use of protective clothing is recommended, such as dust mask, protective gloves, sturdy non-slip footwear, helmet and ear defenders.
WARNING To reduce the risk of injury in applications that produce a considerable amount of dust, use a Milwaukee dust extraction solution in accordance with the solution’s operating instructions.
The dust produced when using this tool may be harmful to health.
Do not inhale the dust. Wear a suitable dust protection mask.
Do not machine any materials that present a danger to health (e.g. asbestos).
Switch the device oﬀ immediately if the insertion tool stalls! Do not switch the device on again while the insertion tool is stalled, as doing so could trigger a sudden recoil with a high reactive force.
Determine why the insertion tool stalled and rectify this, paying heed to the safety instructions.
The possible causes may be:

it is tilted in the workpiece to be machined
it has pierced through the material to be machined
the power tool is overloaded

Do not reach into the machine while it is running.
The insertion tool may become hot during use.
WARNING! Danger of burns

when changing tools
when setting the device down

Chips and splinters must not be removed while the machine is running.
When working in walls ceiling, or ﬂ oor, take care to avoid electric cables and gas or waterpipes.
Clamp your workpiece with a clamping device. Unclamped workpieces can cause severe injury and damage.
Remove the battery pack before starting any work on the machine.
Do not dispose of used battery packs in the household refuse or by burning them. Milwaukee Distributors oﬀer to retrieve old batteries to protect our environment.
Do not store the battery pack together with metal objects (short circuit risk).
Use only System M12 chargers for charging System M12 battery packs. Do not use battery packs from other systems.
Battery acid may leak from damaged batteries under extreme load or extreme temperatures. In case of contact with battery acid wash it oﬀ immediately with soap and water. In case of eye contact rinse thoroughly for at least 10 minutes and immediately seek medical attention.
Do not insert the bit on the tool when the tool is running, and switch is lock on status, the bit will be running and may hurt the user.
Warning! To reduce the risk of ﬁ re, personal injury, and product damage due to a short circuit, never immerse your tool, battery pack or charger in ﬂuid or allow a ﬂuid to ﬂow inside them. Corrosive or conductive ﬂuids, such as seawater, certain industrial chemicals, and bleach or bleach containing products, etc., can cause a short circuit.

SPECIFIED CONDITIONS OF USE

M12 FDD2: The battery drill/screwdriver may be used for drilling and screwdriving for independent use away from mains supply.
M12 FPD2: The electronic battery percussion drill/screwdriver is designed for drilling, percussion drilling, as well as screwdriving for independent use away from mains supply.
Do not use this product in any other way as stated for normal use.

RESIDUAL RISK

Even when the product is used as prescribed, it is still impossible to completely eliminate certain residual risk factors. The following hazards may arise in use and the operator should pay special attention to avoid the following:

Injury caused by vibration
Hold the product by designated handles and restrict working time and exposure.
Exposure to noise can cause hearing injury.
Wear ear protection and limit exposure.
Injury due to ﬂying debris
Wear eye protection, heavy long trousers, gloves and substancial footwear at all times.
Inhalation of toxic dusts.

NOTES FOR LI-ION BATTERIES

Use of Li-Ion batteries
Batteries which have not been used for some time should be recharged before use.
Temperatures in excess of 50°C (122°F) reduce the performance of the battery. Avoid extended exposure to heat or sunshine (risk of overheating).
The contacts of chargers and battery packs must be kept clean.
For an optimum life-time, the batteries have to be fully charged, after used.
To obtain the longest possible battery life remove the battery pack from the charger once it is fully charged.
For battery storage longer than 30 days:
Store the battery where the temperature is below 27°C and away from moisture
Store the battery in a 30% – 50% charged condition
Every six months of storage, charge the battery as normal.
Battery protection for Li-Ion batteries
In extremely high torque, binding, stalling and short circuit situations that cause high current draw, the tool will vibrate for about 5 seconds, the fuel gauge will ﬂash, and then the tool will turn OFF. To reset, release the trigger.
Under extreme circumstances, the internal temperature of the battery could become to high. If this happens, the fuel gauge will ﬂ ash and the battery pack cool and then continue work.
Transport of Li-Ion batteries
Lithium-ion batteries are subject to the Dangerous Goods Legislation requirements.
Transportation of those batteries has to be done in accordance with local, national and international provisions and regulations.

The user can transport the batteries by road without further requirements.
Commercial transport of Lithium-Ion batteries by third parties is subject to Dangerous Goods regulations. Transport preparation and transport are exclusively to be carried out by appropriately trained persons and the process has to be accompanied by corresponding experts.

When transporting batteries:

Ensure that battery contact terminals are protected and insulated to prevent short circuit.
Ensure that battery pack is secured against movement within packaging.
Do not transport batteries that are cracked or leak.

Check with forwarding company for further advice

CLEANING
The ventilation slots of the machine must be kept clear at all times.

MAINTENANCE

Use only Milwaukee accessories and Milwaukee spare parts. Should components need to be replaced which have not been described, please contact one of our Milwaukee service agents (see our list of guarantee/service addresses).
If needed, an exploded view of the tool can be ordered. Please state the machine type printed as well as the six-digit No. on the label and order the drawing at your local service agents or directly at: Techtronic Industries GmbH, Max-Eyth-Straße 10, 71364 Winnenden, Germany.

SYMBOLS

| Please read the instructions carefully before starting the machine.
---|---
| CAUTION! WARNING! DANGER!
| Remove the battery pack before starting any work on the machine.
**| Always wear goggles when using the machine.
Wear ear protection | Wear ear protectors!
**| Wear a suitable dust protection mask.
**| Wear gloves!
| Accessory – Not included in standard equipment, available as an accessory.
| Do not dispose of waste batteries, waste electrical and electronic equipment as unsorted municipal waste. Waste batteries and waste electrical and electronic equipment must be collected separately.
Waste batteries, waste accumulators and light sources have to be removed from equipment.
Check with your local authority or retailer for recycling advice and collection point.
According to local regulations retailers may have an obligation to take back waste batteries and Waste electrical and electronic equipment free
of charge.
Your contribution to re-use and recycling of waste batteries and waste electrical and electronic equipment helps to reduce the demand of raw
materials.
Waste batteries, in particular containing lithium and waste Electrical and electronic equipment contain valuable, recyclable materials, which can adversely impact the environment and the human health, if not disposed of in an environmentally compatible manner.
Delete personal data from waste equipment, if any.
n0| No-load speed
V**| Voltage
| Direct Current
| European Conformity Mark
| British Conformity Mark
| Ukraine Conformity Mark
| EurAsian Conformity Mark

EC DECLARATION OF CONFORMITY
We declare as the manufacturer under our sole responsibility that the product described under “Technical Data” fulﬁlls all the relevant regulations and directives listed below and that the following harmonized standards have been used.

2011/65/EU (RoHS)
2014/30/EU
2006/42/EC| S.I. 2008/1597 (as amended)
S.I. 2016/1091 (as amended)
S.I. 2012/3032 (as amended)
---|---
EN 62841-1:2015
EN 62841-2-1:2018+A11:2019
EN IEC 55014-1:2021
EN IEC 55014-2:2021
EN IEC 63000:2018| BS EN 62841-1:2015
BS EN 62841-2-1:2018+A11:2019
BS EN IEC 55014-1:2021
BS EN IEC 55014-2:2021
BS EN IEC 63000:2018
Winnenden, 2021-12-06| Winnenden, 2021-12-06
Alexander Krug
Managing Director| Alexander Krug
Managing Director

Authorized to compile the technical ﬁle:
Techtronic Industries (UK) Ltd
Parkway
Marlow SL7 1YL
UK
Techtronic Industries GmbH
Max-Eyth-Straße 10
71364 Winnenden
Germany

Copyright 2022
Techtronic Industries GmbH Max-Eyth-Str. 10
71364 Winnenden
Germany
+49 (0) 7195-12-0
www.milwaukeetool.eu
Techtronic Industries (UK) Ltd
Parkway
Marlow SL7 1YL
UK
(03.22)
4931 4706 28

Documents / Resources

| milwaukee M12 FDD2 Li-Ion RedLithium Brushless Cordless Percussion Drill [pdf] Instructions
M12 FDD2, M12 FPD2, Li-Ion RedLithium Brushless Cordless Percussion Drill, Brushless Cordless Percussion Drill, Li-Ion RedLithium Percussion Drill, Percussion Drill, Drill
---|---