SHARPER IMAGE 208747 Multi-Function Electric Kettle User Manual
- June 9, 2024
- Sharper Image
Table of Contents
Multi-function Electric Kettle
USER MANUAL
Thank you for buying our kettle! Please read the instructions carefully before using the kettle!And keep it properly for reference when necessary!
Kettle Description & Parts
Subject to the actual product
• Parts
Product Name| Type| Capacity| Rated Watts| Rated Voltage| Rated frequency|
Compled Standard
---|---|---|---|---|---|---
Liquid Heater (Electric Water Heater)| Sy-616
SY-617
SY-618A| 380mL| 300W| 120V—| 60Hz| CA 4706.1.2005
684706.19.2008
- Products vary in the appearance, the plctu es above are for reference only. All products are subject to the actual ones.
- New updates on the products are subject to be shown In the latest manual, without prior notice.
Operating Instructions
Before Use
- Remove the cover, add water and make sure water within the max level. When water is boiled, empty the kettle and clean the pot with clean water. For a better cleaning, please repeat the whole process.
- Make sure water below the max level of the pot or it may spill out of the kettle when boiled.
- Ifthe kettle is powered on without water in the pot, its service life will be reduced.
- Switch on, the buzzer ticks, the kettle is ready to use when the indicator display lights up for a second and displays “- – -” Touch “TOUCH SWITCH’ button: first press, it shows 212°F,second press, it shows 195°F,third press,it shows 175°F,and fourth press,it shows 140°F. When the temperature is set. the figure will flash 3 times, and the kettle starts to heat water. The temperature rises to the set one, the buzzer will tick 3 times, and the kettle starts automatic insulation (The actual temperature will be displayed), the temperature can be maintained for 12 hours.
- If continuous heating or reheating is needed, switch on when the kettle cools down.
- The unit is designed for water draining and steam venting
- The kettle can be covered when heating water. Remove the cover when stewing, or the vent holes on the cover will be obstructed
IMPORTANT SAFEGUARDS
• Warning
Please read the following instructions carefully before you use to avoid any
injuries or damages.
- Never immerse the unit in water or other liquids.
- Keep close eyes when the kettle is used near a child
- The kettle is not intended to use by persons with mental disabilities or children
- Do not leave the kettle running without close supervision
- Unplug the power cord before cleaning
- leave the kettle cool before cleaning or storing
- When any part is damaged directly return the kettle to the service center for inspection and maintenance.
- Keep the kettle away from electric stove or microwave.
- Leave it on a flat surface
- Do not heat other stuff rather than water
- Do not overfill the kettle or boiled water may spill out.
- Do not switch the kettle on without water inside.
- Make sure the kettle is on a flat surface when water is filled
- Power cord replacement must be conducted by the manufacturer or the service center
- Plug the cord into an outlet. Switch on the kettle. Power indicator lights up. The kettle starts to heat
- When not in use, switch off, unplug the power cord.
CLEANING & CARE
Always turn the kettle off and remove the plug from the outlet before cleaning I
IMPORTANT SAFEGUARDS
- Switch the kettle off and remove the plug from the outlet before cleaning. Wipe the kettle body with a damp mop.
- When scale is spotted use vinegar to dissolve it. Put 1 teaspoon of vinegar and 2 teaspoons of water into the kettle. Switch on the power. Boil the vinegar and water. Leave it cool. Unplug and rinse several times with clean water. The removal of built-up scale from the inner pot will help extend the life of the kettle.
- Empty the kettle after each use and put it in a cool place,keeping away from sunshine
CIRCUIT DIAGRAM
For reference only, subject to change without prior notice!
Food grade material
Components | Material | Testing Results |
---|---|---|
Stainless Steel Inner Pot NTC Stainless Steel Case | Stainless Steel | |
06CrI9Ni10(304) | Compliance with the standard Requirements | |
Cover | PP(polypropylene) | Compliance with the standard Requirements |
N TC sea I ri ng | PDMS (Silica gei ) | Complvicesvith the standard Requirements |
Notice:
- The components and materials used fix different types of kettles may vary, al are subject to the actual products.
- Please Imp the stainless steel parts away from the add stuff
Environmental Protection Material
The information listed in the table below is based on the requirements of
SJ/T113664 and GB/T 26572.
Product Name: Electric kettle
Components| Hazardous materials
pb| Hg| Cd| (Cr (vi))| (P1113)| (PBDE)
Plastic Parts| 0| 0| 0| 0| 0| 0
Circuit Board| X| 0| 0| 0| 0| 0
Heating Unit| 0| 0| 0| 0| 0| 0
Hardware| 0| 0| 0| 0| 0| 0
Power Cord| 0| 0| 0| 0| 0| 0
reweviseSenscr| X| 0| 0| 0| 0| 0
Screw| 0| 0| 0| 0| 0| 0
Paling Materal| 0| 0| 0| 0| 0| 0
NI the Information listed in the table is based on the regulations of Si/T
11364.
0 means the amount of the hazardous material contained In the associated part
is below the max limit specified In the requirements of GBP 26572.
X: means the amount of the hazardous material contained In the associated part
Is above the max limit specified In the requirement of GB/126572 due to the
restriction of the current technology, and should be Improved when the new
technology is available.