ExBrite JTJSBM4836DKSXBLX LED Mirror Instructions
- June 9, 2024
- ExBrite
Table of Contents
JTJSBM4836DKSXBLX LED Mirror
Instructions
JTJSBM4836DKSXBLX LED Mirror
WARNING AND SAFETY INSTRUCTIONS
Before assembling your LED Lighted Mirror fixture, please make sure that you
carefully read through this instruction sheet, refer back to them during
installation to ensure your product is fitted safely and correctly. Keep these
instructions for future use.
WARNING Risk of Fire and Electric Shock
- All fittings must be installed in accordance with current IEE wiring regulations. If indoubt, consult a qualified electrician.
- Switch off the electrical supply at the main circuit board BEFORE installation and maintenance.
- Suitable for indoor use only. This product should be positioned well away from curtains and fabrics. Never cover the mirror.
- Regularly check the cord, the transformer and all other parts for damage, if any part is damaged the product should not be used.
INSTALLATION SAFETY
-
Inspect the product immediately upon receipt for the transit damage or missing parts.
Handle the product with care and protect against knocks to all sides and edges of the glass. -
Ensure there are no hidden pipes or cables in the wall before drilling.
-
Wear suitable eye protection when drilling. Take care if drilling on tiled surfaces in case the drill slips.
CAUTION
The light source of this product is non-changeable light diodes (LED). Do not
disassemble the product, as the light diodes can cause damage to the eyes.
NOTE: The important safeguards and instructions that appear in this
manual are not meant to cover all possible conditions and situations that may
occur. It must be understood that common sense, caution and care are factors
that can’t be built into any product. These factors must be supplied by the
person(s) caring for and operating the fixture. Do not install this fixture in
hazardous locations.
PRODUCT DESCRIPTION & INFORMATION
TOOLS YOU MAY NEED
Installation accessories
INSTALLATION PROCESS
Step 1
Measure the distance between the holes on the hanging bar, use an electric
drill and punch holes on the wall Step 2 Fix the hanging bar to the wall
with screws, (Drive the expansion plug into the hole on wall. then put screw
into the expansion plug) Step 3
If wiring installation is required, ensure that the mirror is turned off when
the power supply in the house is cut off. Then connect the power cord of the
mirror and the on the wall with the terminal block .
White wire = Neutral wire, black wire = Live wire, Light green wire = Earth
wire. Warning: Always switch off the electrical supply at the mains during
installation and maintenance.
Do not switch on the electrical supply at the mains until the end of the
installation.
Step 4 Hang the mirror with desired placement by mirror
OPERATION PROCESS
-
Light on/off
Press to turn on the light, long press to steplessly adjust the color temperature, short press to turn off the light.
Press to turn on the light, long press to steplessly adjust the brightness, short press to turn off the light -
Anti-fog function
Short press to turn on/off defogging
Power-off memory: When the light is turned on, the power is turned off directly, and the light will automatically light up when the power is turned on next time. If the power is turned off when the light is off, you need to touch the switch button to turn on the light when you turn on the power next time.
LED Mirror Power Source FAQ
Scenario 1
(Direct Wired)
This is the most common way to connect the mirror. The LED light & anti fog
pad are both controlled by the built-in touch switch on the mirror.
*The LED light is dimmable. Scenario 2
(Wall Switch)
By doing so, the mirror is now bridged to the wall switch. In order to turn on
the mirror,the wall switch needs to be on. The touch switch can be used to
turn on the LED mirror and anti-fog pad. The mirror shuts down once the wall
switch is filpped to OFF. Scenario 3
(Wall Dimmer Switch – Not Accepted) This is a scenario that is not acceptable.
There is no work around for our mirror. Do not try this way as it will damage
the LED driver. THANK YOU FOR CHOOSING US.
We wish you have wonderful experience in our product. If you have any queries,
please feel free to contact us by email:
info@exbriteusa.com. For more Exbrite products,
please scan the following QR code.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>