GENKI HTGW Waveform Earbuds User Manual
- June 4, 2024
- GENKI
Table of Contents
User Manual for HTGW
Earbuds FCC ID 2ARPB-HTGW
What’s inside
1 x Waveform Earbuds
1 x Waveform SmartCase
6 x Silicone Tips
6 x Memory Foam Tips
6 x Wing Tips
1 x USB Charging / Transmitter Cable (1.2m)
1 x 3.5mm Audio Jack Cable (0.8m)
Getting Started
Charge the Earbuds
Connect to your Devices
Direct Bluetooth Connection For a convenient wireless connection to your
Bluetooth-compatible device.
– Open the Smart Case and remove the Waveform Earbuds, the lights on the
earbuds turn on and blink indicating pairing mode is active.
– Check your Bluetooth settings in the source device (smartphone, tablet,
computer, game console) and pair to “Genki Waveform”
Smart Case aptX Adaptive Connection
For high fidelity, low latency connection through USB Audio or headphone jack.
– Ensure Waveform Earbuds are inside the SmartCase.
– Connect the SmartCase to your source device (smartphone, tablet, computer,
game console) with the included cable.
– Open the SmartCase and remove the Waveform Earbuds, the lights on the
earbuds will stop blinking when automatically updating the connection to the
SmartCase.
DualStream Connection (Bluetooth and SmartCase)
For streaming two audio sources simultaneously.
– Follow the instructions previously for the Smart Case aptX Adaptive
Connection to connect your primary audio source.
– On your secondary audio source check your Bluetooth settings and pair to
“Waveform Dualstream”
How to use the Waveform?
SmartCase Control
The SmartCase controls are only available when it is connected via type C
cable.
Lights Indicator
Location of the lights
The lights are
located on the SmartCase and Waveform.
When connecting directly:
| Light on the Waveform | Status |
|---|---|
| On | |
| Pairing | |
| Low Battery |
When SmartCase is connected via type C cable:
| Light on the SmartCase | Status |
|---|---|
| Connecting to Waveform |
| Searching
for mixed device
| Battery lower than 15%
Smartcase Microphone
By delegating the microphone function to the case, you no longer need to compensate for audio quality for voice chat. After connecting to the smart case.
Disconnect the device
To disconnect the waveform from a device hold the left and right ear for 5
seconds.
Disconnect
Hold left and right ear for 5sec
Reset to factory setting
Place the earbuds back into the case, and link the Smartcase to any console or laptop. Press and hold the button ‘Ion the SmartCase for 5 seconds. A red light will blink 3 times.
App Feature
Our app “Genki Waveform” can be downloaded on the Apple store and Google Play.
App Feature
Adaptive Noise Cancelling Equalizer Presets
Specifications
Bluetooth Codecs
AptX – Adaptive
AptX – Classic
AAC
SBC
Bluetooth Profiles
A2DP v1.3.1
AVRCP v1.6.1
HFP v1.71
HSP v1.2
BLE GATT (Generic Attribute Profile)
Frequency Band
Tx mode: 2402MHz to 2480MHZ, ISM Band
Rx mode: 2402MHz to 2480MHz, ISM Band RF output power < Or =10.0 dBm
Driver Units 1Omm Dynamic Drive with Balanced Armature Frequency Range 10Hz to
20kHz
Distortion (THD) <0.3% (IkHz/10mW)
Battery Life
Up to 7 hours of Bluetooth
Weight 6.5g for each earbud, 47g for the charging case
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>