BUNN 38300.0066 BX Speed Brew Classic 10-Cup Coffee Brewer User Manual
- June 9, 2024
- BUNN
Table of Contents
BUNN 38300.0066 BX Speed Brew Classic 10-Cup Coffee Brewer
Warning: TO REDUCE RISK OF FIRE OR ELECTRIC SHOCK DO NOT DISASSEMBLE THE COFFEE MAKER NO USER-SERVICEABLE PARTS INSIDE REPAIR SHOULD BE DONE BY AUTHORIZED SERVICE PERSONNEL ONLY
FEATURES
- Brew Funnel
- Lid
- Internal Hot Water Tank
- Drip-Free Glass Carafe
- Carafe Lid
- Warmer Plate
- Sprayhead
- Warmer Switch
- Tank Power Switch
- Pour-In Bowl
- Thermal Carafe
- Thermal Carafe Lid
- Base
- Top Cover
SAFEGUARDING
Important
Follow basic safety precautions when using electrical appliances to reduce the risk of fire, electric shock and personal injury.
- READ ALL THE INSTRUCTIONS IN THIS MANUAL.
- Use caution This coffee maker produces hot liquids: hot liquids can burn you
- Place and use the coffee maker on a level surface.
- Do not touch hot surfaces. Use handles.
- Do not tip the coffee maker.
- To protect against electric shock, do not place the cord, plugs, or coffee maker in water or other liquids.
- Do not open the lid during brewing.
- Close supervision is necessary when the coffee maker is used around children.
- The internal hot water tank contains hot water. Before cleaning, removing or replacing parts, press the power switch off, unplug the coffee maker and let it cool (up to 2 hours.)
- Do not operate the coffee maker with a damaged cord or plug, or any other malfunction or damage. Return the appliance to an authorized service facility for examination, repair or adjustment.
- Using an accessory not evaluated for use with this coffee maker may cause injury.
- Use the coffee maker indoors only.
- Do not let the cord hang over the edge of the table or counter.
- Do not place the coffee maker in or near a hot gas or electric burner, in a heated oven, or in any other heated area.
- Do not use a carafe on a range top or in a microwave.
- Do not use the coffee maker for any purpose other than its intended use.
- Do not remove the brew funnel or carafe while brewing.
- Do not set a hot carafe on a cold surface.
- Do not use a cracked carafe or a carafe with a loose or weakened handle.
- Do not pour any liquid into the internal hot water tank other than water or vinegar for cleaning, as specified in this manual.
- Do not clean the carafe with cleansers, steel wool pads, or other abrasive materials.
- When the coffee maker is not in use, keep a lid in the closed position.
- To disconnect, turn any control to the OFF position, then unplug from the wall outlet.
INITIAL SETUP
DO NOT PLUG IN THE COFFEE MAKER UNTIL STEP 5, OR YOU RISK PERMANENTLY
DAMAGING THE MACHINE.
Follow the steps on the next page for proper setup.
-
Slide empty brew funnels into funnel rails.
-
Fill the carafe with water. Pour Water into the coffee maker.
NOTE: Keep the lid open. -
Place the carafe under the funnel. Close lid. Wait 4 minutes while the internal tank fills.
-
Repeat steps 2 and 3 until water flows from the funnel.
-
Plug in the coffee maker.
-
Press the power switch located on the side. (I=ON, O=OFF) Wait 15 minutes for the water in the tank to heat.
HAVE QUESTIONS? bunn.com/home-products/setup
HOW TO BREW
- Place a BUNN® coffee filter into the brew funnel
- Scoop ground coffee into the filter
- Gently shake the brew funnel to level the grounds
- Slide the funnel into the funnel rails
- Fill the carafe with water: 20oz for 4 cups, 50oz for 10 cups.
- Open lid, and pour water into the coffee maker
- Position the carafe on the warmer plate (or on the base for Thermal models*)
- Close the lid**
- Turn on the warmer switch
- Wait 4 minutes for the drip-out to complete
NOTE:
- Your thermal carafe holds coffee hot for about 2 hours. For best results, preheat the carafe by filling it with hot water, let sit for 30 seconds, then empty before beginning to brew.
- Opening lid during the brew will stop water flowing into the funnel. Coffee will stop flowing out of the funnel when drip-out is complete.
BASIC CLEANING
FOR SPEED BREW MODELS: (Excluding Thermal models)
- Wash the brew funnel and glass carafe after each use.
- Both are top-rack dishwasher safe.
Important: Separate the carafe lid from the carafe when washing in the dishwasher, and use the top shelf only for both the glass and the lid. If washing by hand, use a mild, non-abrasive dish soap.
- Wipe the outside of the coffee maker occasionally, including the area above the brew funnel.
NOTE: After wiping down, ensure that the warmer switch is in the OFF position.
FOR THERMAL MODELS:
Important: Do not use an abrasive device to clean the carafe, because it will scratch the stainless steel. Occasionally, remove the brew-through valve on the Thermal Carafe lid and clean it with mild, non-abrasive detergent. To remove the valve, lift at the edge and pull up. Be sure to clean the passage where the valve is located (valve not on all models).
- To remove coffee stains from inside the thermal carafe, place a paper filter in the brew funnel and pour 2 teaspoons of powder dishwasher detergent into the brew funnel.
- Pour one carafe of water into the coffee maker.
- Place the carafe under the funnel and close the lid.
- When the brewing cycle stops, remove the brew funnel and discard the filter.
- Rinse the funnel.
- Allow the carafe to sit for about 15 minutes.
- Use a soft-bristled brush to clean the inside and outer rim of the carafe.
- Scrub the carafe and pour the lip and lid with a soft cloth, warm water, and mild detergent.
- When finished, pour out the solution into the carafe.
- Rinse the carafe and the lid.
CLEANING THE SPRAY HEAD
Cleaning the sprayhead tube removes deposits formed by natural mineral content
in your water. The more mineral content in your water, the more you should
clean.
A good rule of thumb is to clean it every 3 months.
If you have very hard water, then twice a month may be necessary.
You will need a toothpick, dish soap, and a soft cloth.
- Press the tank power switch to the OFF position, unplug the coffee maker, and allow it to cool for at least 2 hours.
- Remove the funnel and unscrew the spray head, loosening it with your fingertips.
- Reinsert funnel in the machine.
- Pour a carafe of fresh water into the coffee maker. Keep lid open.
- Place the empty carafe under the funnel and close the lid. Water will flow into the carafe.
- Check the spray head holes and clear any deposits with the toothpick.
- Clean the spray head with a cloth and dish soap. Rinse with water.
- Empty the water from the carafe and replace the empty carafe under the funnel.
- Remove the brew funnel and reinstall the spray head. Reinsert the brew funnel.
- Plug in the coffee maker. Press the tank power switch to the ON position.
- Wait 15 minutes for the water in the tank to reach brew temperature.
- Your machine is again ready for brewing.
NOTE: For a replacement sprayhead, call customer service at 1- 800-352-2866 (USA) or 1-800-263-2256 (Canada).
ROUTINE CLEANING
Routinely clean your coffee maker every 3 months. More frequency may be
needed, depending on the mineral content in your water.
Routine cleaning of your coffee maker removes mineral deposits in the internal
hot water tank and will prolong the life of your coffee maker.
You will need: 1 quart (32oz) of white vinegar, a toothpick and dish
soap.
- Slide the brew funnel into the funnel rails.
- Place the carafe under the funnel.
- Open the lid and pour the vinegar into the coffee maker.
- Close the lid. Empty the carafe when the liquid stops flowing.
- Flip the tank switch to the OFF position and unplug the coffee maker. Allow the vinegar to sit in the coffee maker for at least 2 hours.
- Remove the brew funnel and unscrew the spray head. Check the spray head holes and clear any deposits with the toothpick.
- Clean the spray head with a cloth and dish soap.
- Rinse with water.
- Pour a carafe of fresh water into the coffee maker. Place the carafe under the funnel and reinsert the funnel.
- Close the lid (the water will begin to flush out the vinegar from the internal hot water tank).
- Empty the carafe when the liquid stops flowing.
- Repeat the process of cycling fresh cold water 3 or more times, or until you no longer smell vinegar.
- Remove the funnel and reattach the spray head.
- Replace the funnel and place the carafe under the funnel. Plug in the coffee maker. Flip the tank switch to the ON position.
- Allow the water in the tank to reach brewing temperature (which should take about 15 minutes). Your coffee maker is again ready for brewing.
Questions? Contact customer service at: 1- 800-352-2866 (USA) or 1-800-263-2256 (Canada).
DRAINING THE COFFEE MAKER
WATER IN THE COFFEE MAKER SHOULD BE DRAINED WHEN THE COFFEE MAKER IS:
- Transported
- Shipped
- Stored in an unheated location with a chance of freezing
- Not to be used for an extended period of time
TO DRAIN:
- Flip the tank switch to the OFF position, unplug the coffee maker, and allow it to cool for at least 2 hours.
- Remove the funnel and the spray head, loosening with your fingertips.
- Grasp the back of the coffee maker and turn it upside down over a sink.
- Continue tipping the coffee maker until the flow from the spray head tube and lid stops.
- Attach the spray head and insert the funnel into the coffee maker.
- Return the coffee maker to the upright position.
TROUBLESHOOTING
WARRANTY
Bunn-O-Matic Corporation (“BUNN”) warrants the BUNN® Speed Brew Coffee maker, except glass carafe, to be free from defects in materials and workmanship existing at the time of manufacture and appearing within the later of the following warranty periods:
- Three (3) years from the date of original purchase of a NEW Coffee maker with the delivery of a valid receipt evidencing such purchase or, in the absence of such a receipt, from the date of manufacture; or
- One (1) year from the date a REPAIRED OR REPLACEMENT Coffee maker is received by the customer, in the case, BUNN determined a coffee maker returned within the NEW Coffee maker warranty period required to repair or replacement. If such a defect appears during the warranty period, we will (at our sole option) repair or replace the defective Coffee maker with no charge for service or parts, provided the Coffee maker is delivered at the customer’s expense to one of our authorized service centers (see page 4 for customer service info).
Warranty does not cover claims resulting from misuse, failure to follow
instructions on installation and use, use with water having a high mineral
content, neglect, use of unauthorized attachments, commercial use, use on a
current or voltage other than specified on the Coffee maker, or unauthorized
service during the warranty period on conditions otherwise covered by
warranty.
THIS WARRANTY SHALL BE EXCLUSIVE AND SHALL BE IN LIEU OF ANY OTHER WARRANTY,
WRITTEN, ORAL, OR IMPLIED INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. In any event, the
duration of any warranties implied by law, including but not limited to any
implied warranties of merchantability or fitness for a particular purpose, is
expressly limited to the duration of this limited warranty. Some states do not
allow time limitations on implied warranties, so the above limitation may not
apply to you.
THE CUSTOMER’S EXCLUSIVE REMEDY FOR BREACH OF THIS WARRANTY OR OF ANY IMPLIED
WARRANTY, OR OF ANY OTHER OBLIGATION ARISING BY OPERATION OF LAW OR OTHERWISE,
SHALL BE LIMITED AS SPECIFIED HEREIN TO REPAIR OR REPLACEMENT, AT OUR SOLE
OPTION. IN ANY EVENT, RESPONSIBILITY FOR SPECIAL, INCIDENTAL AND CONSEQUENTIAL
DAMAGES IS EXPRESSLY EXCLUDED. Some states do not allow limitation or
exclusion of incidental or consequential damages, so the above limitation or
exclusion may not apply to you. This warranty gives you specific legal rights;
you may have other rights, which vary from state to state.
TRADEMARKS
BUNN Pour-O-Matic, BUNN, BUNN with the stylized red line, The Horizontal Red Line, Bunn-OMatic, Bunn-O-Matic, Velocity Brew, My Café, Speed Brew, Phase Brew, trifecta, Air Infusion, Quality Beverage Equipment Worldwide, The Mark of Quality in Beverage Equipment Worldwide, A Partner You Can Count On, Brew Better Not Bitter, Brew better, not bitter., Coffee At Its Best, Nothing Brews Like a BUNN, Respect Earth, Respect Earth with the stylized leaf, and coffee cherry design, are either trademarks or registered trademarks of Bunn-O-Matic Corporation.
FAQs
What is the difference between the BX Series and the BXB Series?****
The BX Series is a more basic model with a black and stainless steel finish. The BXB Series is a more advanced model with a black and brushed stainless steel finish.
Do you leave Bunn speed brew on all the time?****
The hot water tank can be kept at the ideal brewing temperature because the coffee maker is made to be left on continuously. You can prepare a portable mug of coffee in around two and a half minutes because the water is constantly hot.
How much coffee do you put in a 10-cup coffee maker?****
In any case, you should use roughly 2 teaspoons of coffee for every 6 ounces of water as a general rule of thumb. Therefore you’ll need to use about 40 tablespoons, or 20 scoops, of coffee to make 10 cups.
How much coffee do you put in a Bunn speed brew?****
Did you know that BUNN built the formula for Speed Brew around science? To ensure that your coffee is great, we’ve evaluated every aspect of the coffee brewing process over many years. Because of this, the recommended coffee grounds-to-water ratio for our coffee machines is 10 teaspoons for 50 ounces of water.
Can you use soft water in a Bunn coffee maker?****
You might require a particular flow restrictor sprayed if you use soft water, brew decaf or finely ground coffee, or both.
How do you make strong coffee in a coffee maker?****
Simply increase the number of grounds used without changing the amount of water you use to produce a stronger beverage. The ratio will change as a result, and the cup will be stronger. The ratio of coffee to water used in most brewing techniques ranges from 1:18 to 1:16. (1 part coffee and 18 to 16 parts water).
How many grams is a 10-cup coffee maker?****
For 10 cups of coffee, we get 83 grams using the golden ratio of 1:18. Be aware that not all coffee makers adhere to this standard.
How much ground do you put in a coffee maker?****
You will want 12-24 teaspoons (or between 3/4 and 1 1/2 cups) of ground coffee to fill a typical 12-cup coffeemaker. This will make enough coffee for 12 6-ounce serves, or roughly six 12-ounce mugs. Just adjust the ratio to fit a smaller pot. Quality is crucial because water makes up the bulk of coffee
Can I turn off my Bunn coffee maker?****
After two hours, the Warmer Plate automatically turns off. To manually turn it off, press the Brew button (the red light will turn off). Hold the Brew button down for three seconds to restart the Warmer Plate.
Why is my Bunn coffee maker not heating?****
The tank heater, limit thermostat, control board, thermal fuses, tank heater switch, and probes are the most typical offenders of this problem. A technician’s knowledge and tools are typically required to determine which one is to blame.
How do you clean a Bunn coffee maker?****
White vinegar and distilled water should be combined, and the mixture should be used to fill the entire coffee pot. Start the brewing process by pouring the descaling solution into the water reservoir.
Can hard water damage a coffee maker?****
You need to stay away from very hard water if you want to safeguard your equipment against scale buildup. A little scale accumulation in your kettle won’t harm anyone if you’re preparing pour-over. Scale building might completely destroy an espresso or coffee maker that you are using.
Video
Download the PDF Link;BUNN BX Speed Brew Classic 10-Cup Coffee Brewer pdf
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>