novopress ACO203XL Concrete Nailer With Gas Cartridge User Manual

Nailer With Gas Cartridge
User Manual

ACO203XL / ACO203XL BT
Translation of the Original Instructions

ACO203XL Concrete Nailer With Gas Cartridge

Proper use

These press devices are intended exclusively for use with press jaws/adaptor jaws and press collars manufactured by Novopress or approved by Novopress in agreement with the system supplier. For further details, please contact the system supplier or Novopress direct.
The devices, press jaws and press collars are to be used exclusively for the purpose of press-fitting pipes and fittings for which the relevant press jaws and press collars have been designed. Any use beyond or different to that described here shall be regarded as improper use.
All work with this tool that does not correspond to proper use may lead to damage to the press device, the accessories or the pipes. Leaks and/or injury may result.
Novopress is not liable for damage resulting from

• the use of unsuitable press tools or press tools from other manufacturers, or
• applications that do not conform to proper use.

Proper use also includes compliance with the Operating Manual, adherence to the inspection and maintenance conditions as well as compliance with the latest versions of all relevant safety regulations.

Basic safety information

The following pictograms are used to highlight sections of text. Please follow these instructions and act with particular caution in these cases. Pass all health and safety  instructions on to other users and technicians.

| WARNING!
This information indicates a potentially dangerous situation that could result in serious injury or death.
---|---
| CAUTION!
This information indicates a potentially dangerous situation that could result in minor injuries and/or material damage.
|   Information!
This information is directly linked to the description of a function or an operating sequence.

Please read this Operating Manual carefully.
The safety instructions it contains must be observed.
Compliance with local safety regulations is essential!

| WARNING!
Read all safety warnings and all instructions.
Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.
Therefore:
– Save all warnings and instructions for future reference.
---|---
| WARNING!
Risk of injury from ejected fragments
Incorrect or improper use or the use of worn or damaged press tools and press devices
carries a risk of injury from ejected fragments.
Therefore:
– Press tools and press devices may only be used by trained personnel.
– Compliance with the specified service work and service intervals is mandatory.
– Check the press tools and press devices for cracks and other signs of wear before each use.
– Separate all press tools and press devices with material cracks or other signs of wear immediately and do not use them any longer.
– Only use press tools and press devices that are in perfect technical condition.
– Following incorrect use, do not use the press tool and press device any longer and have them inspected by an authorised workshop.
| CAUTION!
Unskilled use may lead to a damaged or malfunctioning press tool and press device.
Therefore:
– Replace worn press tools immediately and do not use them any longer.
– Use carrying cases for transport and storage and keep press tools and the press device in a dry room.
– Have damage checked immediately by an authorised workshop.
– Comply with the safety instructions regarding the cleaning and anti- corrosion agents used.
| Information!
Consult the documents provided by the system supplier for handling and assembly instructions for fittings and pipes.

Definition of terms

Symbols on the device and information on the rating plate

Information on the rating plate

Explanation of possible pictograms on the rating plate

| Verification marking Canada and USA
---|---
| Verification marking Canada and USA
| Registration of products on the uniform customs territory.
| Electric devices must not be disposed of as normal household waste. Further information, see section Disposal.
| Verification marking Australia
| CE conformity marking product safety in Europe
| Verification mark GB

Scope of supply

The scope of supply for the standard equipment includes:

ACO203XL / ACO203XL BT
Press device incl. operating manual
Battery charger incl. operating instructions
Battery 18 V ⎓
Safety information
EU Declaration of Conformity /
GB Declaration of Conformity
Carrying case

Optional additional accessories (e.g. press jaws, adaptor jaws, press collars) may also be included. Please contact the system supplier for information on the scope of supply.

Technical Data

510 mm with 5,0 Ah battery
Width:| 80 mm
Net weight:| 3,8 kg (with battery)
Compression range:| Plastic: up to 110 mm 0
Metal: up to 108 mm / 4″ 0
Max. noise level:| 89 db(A) 1)
Noise pressure level:| 78 db(A) 1)
Vibration value:| <2,5 m/s2 2)
Type of protection:| IP20
Temperature range during operation:| -10°C to +50°C
Wireless technology:| Bluetooth® 4.0 smart
Frequency range:| 2402,0 MHz to 2480,0 MHz
Maximum output power:| 1,8 dBm

1. Measurement uncertainty 3 db(A)
2. Measurement uncertainty 1.5 m/s²

Information!
Wear hearing protection.

The stated vibration emission value was measured using a standard test procedure and can be employed for the purpose of comparison with another device.
The stated vibration emission value can also be used to obtain an initial estimate of interruptions during intermittent operation.
Caution The vibration emission value may differ from the stated value while the device is actually in use, depending upon the manner in which the device is used. It may be necessary to establish safety measures to protect operating personnel, depending on the actual conditions of use (intermittent operation.

Battery charger
For information on the function and operation of the battery charger and the rechargeable batteries, please consult the battery charger operating instructions.

Brief description of the press device

7.1 Automatic press cycle (Fig. 1)
The device features an automatic press cycle. This ensures that the pressing operation is always completed. For safety reasons, the automatic press cycle only switches on when the pressing operation has started, i.e. when the fitting starts to be shaped.
After the automatic press cycle has been triggered, the green LED (2) goes out and the pressing operation runs automatically. The pressing operation can then only be stopped by pressing and holding the release button (5). After the pressing operation has been completed, the motor automatically switches off and the green LED (2) lights up again.
If the start button (1) is released before the automatic press cycle begins, the piston in the press device moves back to its starting position. The pressing operation will not  have been completed. The pressing operation must be triggered again.

7.2 Release button (Fig. 1)
The pressing operation can be stopped at any time by pressing and holding the release button (5).
The piston in the press device then returns to its starting position.
7.3 Slidable finger guard (Fig. 1)
The press device is equipped with a slidable finger guard (6) as the press jaws differ in length. Slide the finger guard forwards until you hear it click in as soon as you insert shorter press jaws.
7.4 Rotatable head
The press tool is equipped with a rotatable crimping head. The head is rotatable by 180°. Within the range of these 180° the crimping head can be moved into any position. It is only possible to adjust the crimping head before the pressing operation. The crimping head cannot be rotated while the pressing operation is being performed.
7.5 Stroke limit (Fig. 1)
The press device features a stroke limit. When using shorter press jaws the stroke limit helps save time.
The stroke limit can be switched on and off using an indexing bolt (7) as follows:

• Press the start button (1) with the stroke limit being actuated. Immediately:
• Pull out the indexing bolt (7) and rotate through 90°.
• Allow the indexing bolt (7) to lock into the groove.

Press the start button (1) with the stroke limit being actuated. The indexing bolt can then be pulled out.

7.6 Wireless interface (only ACO203XL BT) (Fig. 1)
The ACO203XL BT device features a wireless interface if it shows the following characteristic:

• Blue LED (10)

This wireless interface together with the NovoCheck app can be used to connect the ACO203XL BT to a mobile terminal device, such as a smartphone, tablet, etc. (Android, iOS; further information at www.novopress.de). The following functions are available:

• Reading the press device
• Checking the press device
• Making settings
• Generating construction site reports.

To establish a connection, the press device must be operational and the NovoCheck app installed on the terminal device.
The press device can now be connected with the NovoCheck app. (For more information, go to www.novopress.de) When the connection to the wireless interface was established successfully, the blue LED (10) lights up.
The blue LED (10) goes out if no connection has been established until the first pressing operation is performed. A new attempt to establish the connection can only be made if the press device has been switched off in the meantime. It may be necessary to pull the rechargeable battery for this.
If you do not wish to establish a connection, press the start button (1) once again and perform the pressing operation.

7.7 Battery

Information!
The batteries are not charged at the factory.
Therefore:
– Charge the batteries before using for the first time.
Information!
Limited temperature range for charging and storing the batteries.
Therefore:
– It is imperative that the operating instructions for the battery charger are complied with.

Removing the battery (Fig. 2)
Push in (1) the two release buttons (A) and then remove the battery (2).
Inserting the battery (Fig. 3)
Slide the battery into the device as illustrated until it clicks into place.
Battery charge indicator (Fig. 2)
The battery charge is displayed when button (B) is pressed. The number of LEDs lit up denotes the battery charge. One flashing LED indicates a maximum power reserve of 10%. The battery must be charged soon.
If the battery is inserted in the press device while the battery charge is being checked, the last pressing operation must have been completed at least 1 minute prior to this. Otherwise the display will be inaccurate.

Information!
The ACO203XL / ACO203XL BT press device must only be operated with 18 V rechargeable lithium-ion batteries. The rechargeable 18 V battery must only be used in the appropriate press devices.

Feature of the press device when the battery is empty:
When a pressing operation begins, a check is made to determine whether the battery charge is sufficient to complete the pressing operation. If this is not the case the device does not start. The green LED (2) flashes.
If the green LED (2) flashes following a pressing operation, the pressing operation was carried out correctly. The battery must be recharged prior to the next pressing operation.

7.8 Energy saving mode
If the press device is not used over an extended period, the device switches off. No LED is lit up any longer. Press the start button (1) briefly to activate the press device.

Commissioning and operation

8.1 Preparing the ACO203XL/ACO203XL BT
CAUTION!
Fingers risk being crushed if the device is operated without a press jaw/adaptor jaw (Fig. 4)
If no press jaw/adaptor jaw is fitted, fingers could be placed in the at-risk zone. Fingers could be crushed when the device is started.
Therefore:
– Do not operate the device without the press jaws.
– Keep your fingers away from the at-risk zone.
CAUTION!
Fingers risk being crushed if the device is operated with the finger guard incorrectly adjusted (Fig. 8)
If the finger guard has not been slid forwards when shorter press jaws are fitted, fingers could be placed in the at-risk zone. Fingers could be crushed when the device is
started.
Therefore:
– Do not operate the device without having slid the finger guard forwards if shorter press jaws have been inserted (Fig. 9).
– Keep your fingers away from the at-risk zone.
CAUTION!
Not locking the retaining pin (8) fully can cause damage to the device.
(Fig. 5 to 7).
If the retaining pin (8) is not fully inserted and locked, the cylinder can break during the pressing operation.
Therefore:
– Press in retaining pin (8) as far as it will go and turn 180° to the rear.

Information!
The press device is not suitable for continuous operation. Following 30 minutes of continuous operation, a short break of at least 15 minutes must be taken to allow the device to cool down.

• Insert and lock the press jaw/adaptor jaw in the press device as shown in Figs. 5 to 7.

8.2 Meaning of the LED display

(see section 7.8).
Green LED (2) lights up.| On standby.|
Green LED (2) off (pressing operation in progress).| Automatic press cycle is on, device ends the pressing operation automatically.|
Green LED (2) flashes.| Insufficient battery charge.| Charge or replace battery.
Blue LED (10) flashes.| The press device is ready for connection.| The press device can be connected with the NovoCheck app.
Blue LED (10) lights up.| The press device is connected with the
NovoCheck app.|
Red LED (3) flashes.| Device not within the temperature range| The device only works within a temperature range of -10 to +50°C. If the red LED is flashing, the device must be
moved into a warmer or colder area. The device can be warmed to operating temperature by means of dry runs. If the device is too warm it must be cooled down by means of a short break.
Red LED (3) lights up.| Device fault.| Press the start button (1). If this is unsuccessful, the press device is defective. Send the device to a specialist workshop.
NOTE!
The pressing operation may not have been completed; please check and repeat if required.
Red (3) and green (2)
LED  flash alternately.| Service interval reached.| Take the press device to be serviced.

8.3 Performing the pressing operation

CAUTION!
Danger of crushing!
There is a risk that fingers and hands will be crushed.
Therefore:
– Keep body parts and foreign objects away from the press jaws during the pressing operation.
– Do not hold the jaw levers with your hands during the pressing operation.
CAUTION!
Keep fingers away from the at-risk zone if no press jaw/adaptor jaw is fitted. (Fig. 4)
Fingers risk being crushed.
Therefore:
– Do not operate the device without the jaws.
– Keep your fingers away from the at-risk zone.

Information!
Always comply with the operating instructions for the press tools!

1. Check whether the nominal width of the press fitting matches the nominal width of the press jaw/press collar.

2. Comply with the system manufacturer’s instructions when fitting the press jaw/press collar (Fig. 10).
   When using a press collar – Fit the adaptor jaw to the press collar as described in the press collar manufacturer’s instructions.
   Information!
   Make sure that the press jaw is fully closed when the pressing operation is complete (Fig. 11)
   Information!
   Ensure there is no gap between the segments of the press collar when the pressing operation is complete.
   Information! (only ACO203XL BT with wireless interface)
   If the press device is switched off, briefly press the start button (1) to activate the press device. Press the start button again to start the pressing operation.

3. To start the process, press the start button.

4. When the pressing operation has been completed:
   • if using a press collar: first detach the adaptor jaw from the press collar, then
   • detach the press jaw/press collar from the press fitting (Fig. 12).

Cleaning, maintenance and repair

CAUTION!
Risk of injury during cleaning or repair work from inadvertently pressing the On switch.
Therefore:
– Comply with the safety instructions and always remove the battery before performing cleaning, servicing or repair work.

Service addresses
Novopress GmbH Pressen und Presswerkzeuge & Co. KG
Welserstr. 7
41468 Neuss
Germany
You can find the addresses of authorised specialist workshops by contacting Novopress or at www.novopress.de.

Service intervals
Service and repair work may only be carried out by Novopress or the authorised Novopress specialist
workshops.
Information!
The next service deadline is indicated on the press device.
This service must be performed at least every 2 years or at the latest when the LED display indicates that a service is due (see Section 8.2 Meaning of the LED display).
Routine inspection (before use, at the start of the working day) and when soiled (Fig. 13+14) Check for visible damage, material cracks and other signs of wear. If defects are found, do not use the device and have it repaired.

Six-monthly inspection
Have the device inspected by a qualified electrician or a Novopress workshop.
Annually to get a 1-year extended warranty (see section 11 Warranty and guarantee)
Have the press device inspected and serviced at Novopress or a Novopress workshop.

Disposal

CAUTION!
Groundwater hazard
The device contains hydraulic fluid.
Hydraulic fluids pose a hazard to groundwater. Uncontrolled drainage or improper disposal is punishable by law.
Therefore:
– Dispose of the device in an environmentally responsible manner.

The instructions in the operating instructions provided with the battery charger must be complied with when disposing of rechargeable batteries and the charger.
**** The product must not be disposed of as residual waste.
Novopress recommends that disposal be carried out by authorised specialist companies.
Alternatively, waste devices can be returned directly to Novopress (or a specialist workshop) for proper disposal.
National disposal guidelines must be observed.

Warranty and guarantee

Novopress provides the full statutory warranty of 24 months for its press devices and tools. The warranty period always commences on the date of delivery, which must be proven by means of the sales documentation in case of doubt.
Within the warranty period, the warranty covers the repair of any damage or malfunction of these tools that is attributable to material or production faults.
The following are not covered by the warranty:

• Damage caused by improper use or inadequate servicing.
• Damage caused by the use of products not approved by Novopress for use with its press devices.
• Damage caused by pressing unsuitable pipes or fittings.

For wearing parts, the Novopress warranty lasts only for the intended service life.
Service work and parts provided in response to warranty claims do not have to be paid for. However, all shipping costs shall be borne by the user.
Claims can only be accepted if the device is delivered to Novopress or a Novopress workshop in an assembled state.
Repair or replacement of the device under warranty does not result in an extension of the warranty period. Repair or replacement can only be performed using as-new components, the function of which corresponds to that of the old components. All parts that are faulty and consequently replaced are the property of the manufacturer.
Extended warranty on expiry of the statutory warranty period
We voluntarily provide the following extended warranties beyond the statutory warranty period
1-year extended warranty for new press devices, adaptor jaws and press collar
Novopress provides an extended warranty of one year for all new press devices, adaptor jaws and press collars that have been serviced at least every 12 months by Novopress or by an authorised Novopress workshop. There is a charge for this service work. For details of costs, please contact Novopress or an authorised Novopress workshop.
3-year extended warranty for new press jaws
Novopress provides an extended warranty of three years for all new press jaws, interchangeable jaws and press inserts that have been serviced at least every 12 months by Novopress or by an authorised Novopress workshop. There is a charge for this service work. For details of costs, please contact Novopress or an authorised Novopress workshop.
Repair warranty
Novopress provides the following repair and spare parts warranty beyond the warranty period for new products that undergo repair after this period:

• 6-month warranty for replaced spare parts.
• 12-month warranty for replaced assemblies.
• 12-month warranty for replaced press devices.

Declarations of Conformity

12.1 EU Declaration of Conformity
EU Declaration of Conformity and list of the observed directives and the applicable standards: see supplement EU Declaration of Conformity.
12.2 GB Declaration of Conformity
GB Declaration of Conformity and list of the observed directives and the applicable standards: see last page of the supplement EU Declaration of Conformity.

GmbH Pressen und Presswerkzeuge & Co. KG
Scharnhorststr. 1
41460 Neuss
Germany
Postfach 101163
41411 Neuss
Germany
Tel.: +49 (2131) 2880
Fax: +49 (2131) 28855
www.novopress.de
E-mail: info@novopress.de

References

• Novopress | Presswerkzeuge & Pressmaschinen seit 1969

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>