Schneider Electric TM5PCRS2 SPS Extension Instruction Manual

June 9, 2024
Schneider Electric

Schneider Electric TM5PCRS2 SPS Extension Instruction Manual

Schneider Electric TM5PCRS2 SPS Extension Instruction
Manual

www.se.com

DANGER

HAZARD OF ELECTRIC SHOCK, EXPLOSION OR ARC FLASH

  • Disconnect all power from all equipment including connected devices prior to removing any covers or doors, or installing or removing any accessories, hardware, cables, or wires except under the specific conditions specified in the appropriate hardware guide for this equipment.
  • Always use a properly rated voltage sensing device to confirm the power is off where and when indicated.
  • Replace and secure all covers, accessories, hardware, cables, and wires and confirm that a proper ground connection exists before applying power to the unit.
  • Use only the specified voltage when operating this equipment and any associated products.

Failure to follow these instructions will result in death or serious injury.

DANGER

POTENTIAL FOR EXPLOSION

  • Only use this equipment in non-hazardous locations, or in locations that comply with Class I, Division 2, Groups A, B, C and D.
  • Do not substitute components which would impair compliance to Class I Division 2.
  • Do not connect or disconnect equipment unless power has been removed or the area is known to be non-hazardous.

Failure to follow these instructions will result in death or serious injury.

Electrical equipment should be installed, operated, serviced, and maintained only by qualified personnel.
No responsibility is assumed by Schneider Electric for any consequences arising out of the use of this material.

WARNING

UNINTENDED EQUIPMENT OPERATION

  • Use appropriate safety interlocks where personnel and/or equipment hazards exist.
  • Install and operate this equipment in an enclosure appropriately rated for its intended environment and secured by a keyed or tooled locking mechanism.
  • Use the sensor and actuator power supplies only for supplying power to the sensors or actuators connected to the module.
  • Power line and output circuits must be wired and fused in compliance with local and national regulatory requirements for the rated current and voltage of the particular equipment.
  • Do not use this equipment in safety-critical machine functions unless the equipment is otherwise designated as functional safety equipment and conforming to applicable regulations and standards.
  • Do not disassemble, repair, or modify this equipment.
  • Do not connect any wiring to reserved, unused connections, or to connections designated as No Connection (N.C.).

Failure to follow these instructions can result in death, serious injury, or equipment damage.

NOTICE

ELECTROSTATIC DISCHARGE

  • Ensure that empty PCI slots have their covers in place before applying power to the controller.
  • Never touch an exposed PCI connector.
  • Store electronic components in their protective packaging until immediately before assembly.
  • Only touch modules on the housing.
  • Take the necessary protective measures against electrostatic discharges.

Failure to follow these instructions can result in equipment damage.

TM5PCRS2

TM5PCRS4          TM5PCDPS

Schneider Electric TM5PCRS2 SPS Extension -
TM5PCRS4,TM5PCDPS

N.C.: not connected

Installation

TM258LD42DT4L,
TM258LD42DT4Lpp,
TM258LF66DT4Lpp,
TM258LF42DRpp
LMC058LF42pp,
LMC058LF424pp

Schneider Electric TM5PCRS2 SPS Extension -
Installation

Uninstallation

TM258LD42DT4L,
TM258LD42DT4Lpp,
TM258LF66DT4Lpp,
TM258LF42DRpp
LMC058LF42pp,
LMC058LF424pp

Schneider Electric TM5PCRS2 SPS Extension -
Uninstallation

UK Representative

Schneider Electric Limited
Stafford Park 5
Telford, TF3 3BL
United Kingdom

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Schneider Electric User Manuals

Related Manuals