SEALEY AP1640 1.52M Woodworking Bench with 4 Drawers Instruction Manual

: June 9, 2024
: SEALEY

Table of Contents

SEALEY AP1640 1.52M Woodworking Bench with 4 Drawers
SAFETY
INTRODUCTION
SPECIFICATION
CONTENTS
ASSEMBLY
ENVIRONMENT PROTECTION
Warranty
Read User Manual Online (PDF format)
Download This Manual (PDF format)

SEALEY AP1640 1.52M Woodworking Bench with 4 Drawers

SEALEY-AP1640-1-52M-Woodworking-Bench-with-4-Drawers-
product

MODEL NO: AP1640

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

Refer to the instruction manual

SAFETY

WARNING! Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using this bench.
Locate the bench in a suitable work area.
Keep the work area clean, uncluttered and ensure there is adequate lighting.
WARNING! Use the bench on level and solid ground, preferably concrete.
Keep the bench clean and tidy in accordance with good workshop practice.
Keep children and unauthorised persons away from the work area.
DO NOT use the bench for any purpose other than for which it is designed.
DO NOT undertake work on the bench without the workpiece being adequately secured.
DO NOT use the bench outdoors.
DO NOT clean the bench with any solvents which may damage the surface or the protective coating on the worktop.
DO NOT get the bench wet or use in damp or wet locations or areas where there is condensation.

INTRODUCTION

Made from Rubber Wood. Features tool well, shelf, 4 tool drawers, front vice, four metal bench stops and four wooden board jacks. Supplied with 4 Wooden Pegs and 4 Anvil Pegs.

SPECIFICATION

Model No: ………………………………………………………… AP1640
Overall Size (W x D x H): ……….. 1520mm x 620mm x 820mm
Worktop: ………………………………………………….1520 x 500mm
Tool Well: ………………………………………………… 1110 x 410mm
Drawer(x4): …………………………………………460 x 390 x 80mm
Vice (x1): …………………………..280mm wide x 180mm opening

Part no.	Description	Quantity
1	Table top	1
2	Shelf	1
3	Cross brace	2
4	Leg	2
5	Vice	1
6	Screw 60mm	4
7	Bolt 90mm	4
8	Connecting nut	4
9	Hex wrench 50mm	1
10	Wood peg	4
11	Anvil peg	4
12	Washer	8
13	Screw 30mm	32
14	Screw 35mm	6
15	Sliding partition	1
16	Lower support	2
17	Drawer front panel (P1)	4
18	Drawer back panel (P2)	4
19	Drawer panel (P3)	4
20	Drawer slot panel (P4)	4
---	---	---
21	Drawer bottom (P5)	4
22	Drawer handle	4
23	Drawer screw (40mm)	8

ASSEMBLY

Step 1: Insert the cross nut with groove (8) into the frame strut (3). Align the cross nut so that the groove is horizontal.
Step 2: Fasten the frame to the foot (4) with 2pcs of 90mm screws (7).
Step 3: After both feet have been attached to the frame strut, the shelf (2) is pushed into the groove.
Step 4: Align the second frame strut (3) and fasten it with the connecting nuts with groove (8) and 2 pcs of 90mm screws (7) on the foot (4). The shelf must snap into the groove of the frame strut.
Step 5: The lower support (16) is attached to the front with 4 pcs of 35mm screws (14) at both ends of the feet.
Step 6: The lower support(16) is also attached to the partition wall with rails (15) using 2 pcs of 35mm screws (14).
Step 7: The legs are then attached to the worktop with 4 pcs of 60mm screws (6), 2 pcs per leg.
Step 8: The partition is also attached to the frame with 2 pcs of 35mm screws (14). WARNING! there are no pre-drilled holes.
Step 9: Attach handles (22) to the front of the drawer (17) with 8 pcs of 40mm drawer screws (23), 2 pcs per drawer.
Step 10: The two side parts of the drawer (19 & 20) are attached to the front of the drawer with 2 pcs of 30mm screws (13) per side, 4 pcs per drawer.
Step 11: The back of the drawer (18) is attached to the two side parts by using 4 pcs of 30mm screws (13), 2 pcs per side. Then insert the bottom of the drawer.
Step 12: After installing the drawers, check whether the inner tracks of the drawer pull outs are pushed all the way forward if not, then push all the way forward.
Step 13: When inserting the drawers, make sure the runner clip is facing forwards see picture, then slide the drawers into the guides.
Step 14: Fasten the holding rods (10) and the bench hooks (11) in the holes provided in the worktop.

ENVIRONMENT PROTECTION

Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids according to local regulations.

Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.

Important: No Liability is accepted for incorrect use of this product.