BOSCH DWF97RU60 Black Wall-Mounted Head Free Rangehood User Manual

DWF97RU60 Black Wall-Mounted Head Free Rangehood

boMsgecywRnthBefeeo-rwhegslcecoidsohbmetmevneeinocree.wecfyiooaotnsnum:dr /

Extractor hood

DWF97…

DWK98…

DWK97…

[en]

User manual and installation instructions

enSafety
Table of contents
INFORMATION FOR USE 1 Safety ………………………………………………………….. 2 2 Avoiding material damage…………………………….. 4 3 Environmental protection and saving en-
ergy …………………………………………………………….. 5 4 Operating modes …………………………………………. 5 5 Familiarising yourself with your appliance …….. 6 6 Basic operation ……………………………………………. 6 7 Home Connect …………………………………………….. 8 8 Hob-based hood control……………………………….. 9 9 Cleaning and servicing …………………………………. 9 10 Troubleshooting…………………………………………. 11 11 Disposal…………………………………………………….. 12 12 Customer Service……………………………………….. 12 13 Accessories……………………………………………….. 12 14 Declaration of Conformity …………………………… 13
15 INSTALLATION INSTRUCTIONS ………………….. 13 15.5 Secure installation ……………………………………… 15
1Safety
Observe the following safety instructions. 1.1General information ¡ Read this instruction manual carefully. ¡ Keep the instruction manual and the
product information safe for future reference or for the next owner. ¡ Do not connect the appliance if it has been damaged in transit. 1.2Intended use This appliance is designed only to be built into kitchen units. Read the special installation instructions. The appliance can only be used safely if it is correctly installed according to the safety instructions. The installer is responsible for ensuring that the appliance works perfectly at its installation location.

Only use this appliance: ¡ For extracting cooking vapour. ¡ In private households and in enclosed
spaces in a domestic environment. ¡ Up to an altitude of max. 2000 m above
sea level. Do not use the appliance: ¡ With an external timer.
1.3Restriction on user group This appliance may be used by children aged 8 or over and by people who have reduced physical, sensory or mental abilities or inadequate experience and/or knowledge, provided that they are supervised or have been instructed on how to use the appliance safely and have understood the resulting dangers. Children must not play with the appliance. Children must not perform cleaning or user maintenance unless they are at least 15 years old and are being supervised. Keep children under the age of 8 years away from the appliance and power cable.
1.4Safe use WARNING Risk of suffocation!
Children may put packaging material over their heads or wrap themselves up in it and suffocate. Keep packaging material away from chil-
dren. Do not let children play with packaging ma-
terial. Children may breathe in or swallow small parts, causing them to suffocate. Keep small parts away from children. Do not let children play with small parts.

2

WARNING Risk of poisoning! Risk of poisoning from flue gases being drawn back in. Room-air-dependent heat-producing appliances (e.g. gas, oil, wood or coaloperated heaters, continuous flow heaters or water heaters) obtain combustion air from the room in which they are installed and discharge the exhaust gases into the open through an exhaust gas system (e.g. a chimney). With the extractor hood switched on, air is extracted from the kitchen and the adjacent rooms. Without an adequate supply of air, the air pressure falls below atmospheric pressure. Toxic gases from the flue or the extraction shaft are sucked back into the living space.
Always ensure adequate fresh air in the room if the appliance is being operated in exhaust air mode at the same time as a room-air-dependent heat- producing appliance is being operated.
It is only possible to safely operate the appliance if the pressure in the room in which the heating appliance is installed does not drop more than 4 Pa (0.04 mbar) below atmospheric pressure. This can be achieved whenever the air needed for combustion is able to enter through openings that cannot be sealed, for example in doors, windows, incoming/exhaust air wall boxes or by other technical means. An incoming/exhaust air wall box alone does not ensure compliance with the limit.
In any case, consult your responsible chimney sweep. They are able to assess the house’s entire ventilation setup and will suggest the suitable ventilation measures to you.
Unrestricted operation is possible if the appliance is operated exclusively in circulating-air mode. WARNING Risk of fire!
Fatty deposits in the grease filters may catch fire. Never operate the appliance without a
grease filter.

Safetyen
Clean the grease filters regularly. Never work with naked flames close to the
appliance (e.g. flambéing). Do not install the appliance near a solid
fuel heating appliance (e.g. wood- or coalburning) unless the heating appliance has a sealed, non-removable cover. There must be no flying sparks. Hot oil or grease ignites very quickly. Always supervise hot oil and fat. Never extinguish burning oil or fat with water. Switch off the cooking zone. Extinguish flames carefully using a lid, fire blanket or something similar. When gas burners are in operation without any cookware placed on them, they can build up a lot of heat. A ventilation appliance installed above the cooker may become damaged or catch fire. Only operate the gas burners with cookware on them. Operating multiple gas hobs at the same time generates a great deal of heat. A ventilation appliance installed above the cooker may become damaged or catch fire. Only operate the gas hobs with cookware on them. Select the highest fan setting. Never operate two gas hobs simultaneously on the highest flame for longer than 15 minutes. Two gas hobs correspond to one large burner. Never operate large burners of more than 5 kW with the highest flame for longer than 15 minutes, e.g. a wok.
WARNING Risk of burns! The accessible parts of the appliance become hot during operation. Never touch these hot parts. Keep children at a safe distance. The appliance becomes hot during operation. Allow the appliance to cool down before
cleaning. WARNING Risk of injury!
Components inside the appliance may have sharp edges. Carefully clean the appliance interior. Items placed on the appliance may fall off. Do not place any objects on the appliance.
3

enAvoiding material damage
Changes to the electrical or mechanical assembly are dangerous and may lead to malfunctions. Do not make any changes to the electrical
or mechanical assembly. The filter cover may swing out. Open the filter cover slowly. Take hold of the filter cover after opening
until it no longer swings out. Close the filter cover slowly. Risk of injury when opening and closing the hinges. Keep your hands away from the hinges. The light emitted by LED lights is very dazzling, and can damage the eyes (risk group 1). Do not look directly into the switched-on
LED lights for longer than 100 seconds. If the appliance is operated by another person via the Home Connect app during cleaning, this increases the risk of injury. Before cleaning, disconnect the appliance
from the Home Connect app. WARNING Danger: Magnetism!
The appliance contains permanent magnets. They may affect electronic implants, e.g. pacemakers or insulin pumps. Persons with electronic implants must
stand at least 10 cm away from the appliance.
WARNING Risk of electric shock! If the appliance or the power cord is damaged, this is dangerous. Never operate a damaged appliance. Never pull on the power cord to unplug the
appliance. Always unplug the appliance at the mains. If the appliance or the power cord is damaged, immediately unplug the power cord or switch off the fuse in the fuse box.
2 Avoiding material damage
ATTENTION! Condensate may cause corrosion damage. To prevent condensation from building up, switch on
the appliance during cooking. If moisture gets into the controls, this may result in damage. Never clean controls with a wet cloth. Incorrect cleaning damages the surfaces. Follow the cleaning instructions.
4

Call customer services. Page 12 Incorrect repairs are dangerous. Repairs to the appliance should only be
carried out by trained specialist staff. Only use genuine spare parts when repair-
ing the appliance. If the power cord of this appliance is dam-
aged, it must be replaced by trained specialist staff. An ingress of moisture can cause an electric shock. Before cleaning, pull out the mains plug or switch off the fuse in the fuse box. Do not use steam- or high-pressure cleaners to clean the appliance.
WARNING Risk of explosion! Highly caustic alkaline or highly acidic cleaning agents in conjunction with aluminium parts in the interior of the appliance may cause explosions. Never use highly caustic alkaline or highly
acidic cleaning agents. In particular, do not use commercial or industrial cleaning agents in conjunction with aluminium parts, e.g. grease filter on extractor hoods.
WARNING Risk of fire! Fatty deposits in the grease filters may catch fire. Clean the grease filters regularly.
WARNING Risk of injury! Improper repairs are dangerous. Repairs to the appliance should only be
carried out by trained specialist staff. If the appliance is defective, call Customer
Service. WARNING Risk of electric shock!
Penetrating moisture may cause an electric shock. Do not use wet sponge cloths.
Do not use harsh or abrasive detergents. Clean stainless steel surfaces in the direction of the
finish only. Never clean controls with stainless steel cleaners. Condensation that flows back in may damage the appliance. The air extraction duct must be installed with a
gradient of at least 1° from the appliance.

Environmental protection and saving energyen

If you put incorrect stress on the design elements, they may break off. Do not pull design elements. Do not place objects on the design elements or
hang objects from them.

There is a risk of surface damage if you do not peel off the protective film. Remove the protective film from all parts of the ap-
pliance before using for the first time. Painted surfaces are easily damaged. Follow the cleaning instructions.
“Cleaning the appliance”, Page 10 Ensure that the painted surfaces are not scratched.

3 Environmental protection and saving energy

3.1Disposing of packaging
The packaging materials are environmentally compatible and can be recycled. Sort the individual components by type and dispose
of them separately.
3.2Saving energy
If you follow these instructions, your appliance will use less power. Adjust the fan speed to the amount of steam produced during cooking. ¡ The lower the fan speed, the less energy is con-
sumed. Only use the intensive mode as required.

If cooking produces large amounts of steam, select a higher fan speed in good time. ¡ The odours are distributed around the room less.
Switch off the lighting if it is no longer required. ¡ When the lighting is switched off, it does not con-
sume any energy. Clean or replace the filters at regular intervals. ¡ The effectiveness of the filter is retained.
Put the cooking lid on. ¡ The cooking vapours and condensation are re-
duced. Only use the additional functions if required. ¡ Switching off additional functions reduces power
consumption.

4 Operating modes
You can use your appliance in air extraction mode or circulating-air mode. The saturation indicator must be adjusted to the selected operating mode and the filters used.
4.1Air extraction mode
The air which is drawn in is cleaned by the grease filters and conveyed to the exterior by a pipe system.
The air must not be discharged into a flue that is used for exhausting fumes from appliances burning gas or other fuels (not applicable to appliances that only discharge the air back into the room). ¡ If the exhaust air is to be conveyed
into a non-functioning smoke or exhaust gas flue, you must obtain the consent of the heating engineer responsible. ¡ If the exhaust air is conveyed through the external wall, a telescopic duct should be used.

4.2Air recirculation mode
The air which is drawn in is cleaned by the grease filters and an odour filter, and conveyed back into the room.
To bind odours in circulating-air mode, you must install an odour filter. The different options for operating the appliance in circulating-air mode can be found in our catalogue. Alternatively, ask your dealer. The required accessories are available from specialist retailers, from customer service or from the Online Shop.

5

enFamiliarising yourself with your appliance
5 Familiarising yourself with your appliance
5.1Controls, variant 1
You can use the control panel to configure all functions of your appliance and to obtain information about the operating status.

Switching the appliance on or off Switching on fan setting 1 Switching on fan setting 2 Switching on fan setting 3 Switching on intensive mode 1 Switching on intensive mode 2

Switching the fan run-on on or off Switching on automatic mode Resetting the filter saturation indicator Home Connect Switching the lighting on or off Setting the brightness

5.2Controls, variant 2
You can use the control panel to configure all functions of your appliance and to obtain information about the operating status.

Switching the appliance on or off Switching on fan setting 1 Switching on fan setting 2 Switching on fan setting 3 Switching on intensive mode 1 Switching on intensive mode 2 Switching the fan run-on on or off
6 Basic operation
6.1Switching on the appliance
Press . a The appliance starts at fan setting 2.
6.2Switching off the appliance
Press .
6

Switching automatic mode on or off Resetting the grease filter saturation indicator Resetting the odour filter saturation indicator Home Connect Switching Ambient Light on or off Switching the lighting on or off Setting the brightness

6.3Setting a fan setting
Press , or .

6.4Switching on intensive mode

If particularly strong odours or vapours develop, you

can use intensive mode.

1. Press

to switch on the intensive setting 1.

2. In order to switch on the intensive setting 2, press .
a After approx. 6 minutes, the appliance automatically switches to fan setting 3.

6.5Switching off intensive mode
Press , or .
6.6Switching on the fan run-on
During the fan run-on, the appliance continues to run for a short time and then switches off automatically. Press . a The fan run-on starts at fan setting 1. a The appliance switches off automatically after ap-
prox. 10 minutes.

6.7Switching off the fan run-on
Press .
6.8Switching on automatic mode1
The optimum fan setting is set automatically using a sensor. Press .
6.9Switching off automatic mode1
Press , or . a The ventilation is automatically ended when the
sensor detects no further change in the room air quality. a Automatic mode runs for a maximum of four hours.

6.10Sensor control
In automatic mode, a sensor in the appliance detects the intensity of the cooking and roasting fumes. Depending on the setting of the sensor sensitivity, the optimum fan setting is automatically switched on. If the sensor control system reacts too weakly or too strongly, the setting for the sensor sensitivity may change. ¡ Factory setting: 3 ¡ Lowest setting: 1 ¡ Highest setting: 5

6.11Setting the sensor control

Requirement: The appliance is switched off.

1. Press and hold .

a The setting is displayed after approx. one second.

2. Press , , ,

or

to change the setting.

3. Release to save the setting.

6.12Switching on the lighting
The lighting can be switched on and off independently of the ventilation system. Note: Colour temperature settings are available in the Home Connect app provided the appliance has this function.

1 Depending on the appliance specifications

Basic operationen
Press .
6.13Setting the brightness
Press and hold until the required brightness is reached.
6.14Switching on Ambient Light1
You can switch on the Ambient Light independently of the ventilation system. Press .
6.15Ambient Light1 – Setting the brightness
Press and hold until the required brightness is reached.
6.16Ambient Light1 – adjusting the colour
Requirement: The appliance is switched off. 1. Press . 2. Press or repeatedly until the required colour is
set.
6.17Setting the intermediate position for the filter cover
On some appliances, the filter cover can be adjusted to an intermediate position. The intermediate position can be used to eliminate particularly strong cooking smells and large amounts of steam. Take hold of the filter cover in the centre and open it
carefully.
6.18Resetting the saturation indicator, variant 1
After cleaning the grease filter or after changing the odour filter, the saturation indicator can be reset. Requirements ¡ After the appliance has been switched off, and 1
appears on the display for the grease filter. ¡ After the appliance has been switched off, and 2
appears on the display for the odour filter. Press . a The saturation indicator is reset.
6.19Resetting the saturation indicator, variant 2
After cleaning the grease filter or after changing the odour filter, the saturation indicator can be reset. Requirements ¡ After the appliance has been switched off, ap-
pears in the display for the grease filter. ¡ After the appliance has been switched off, ap-
pears in the display for the odour filter. 1. To reset the saturation indicator for the grease filter,
press . 2. To reset the saturation indicator for the odour filter,
press . a The saturation indicator is reset.
7

enHome Connect

6.20Setting the saturation indicator

The saturation indicator must be adjusted depending on the filter used.

Requirement: The appliance is switched off.

1. Press and hold

.

To set circulating-air mode (non-regenerable fil-

ter), press .

To set circulating-air mode (regenerable filter),

press .

7 Home Connect
This appliance is network-capable. Connecting your appliance to a mobile device lets you control its functions via the Home Connect app, adjust its basic settings and monitor its operating status. The Home Connect services are not available in every country. The availability of the Home Connect function depends on the availability of Home Connect services in your country. You can find information about this at: www.home-connect.com. The Home Connect app guides you through the entire login process. Follow the instructions in the Home Connect app to configure the settings. Tips ¡ Please consult the documents supplied by
Home Connect. ¡ Please also follow the instructions in the Home Con-
nect app. Notes ¡ Please note the safety precautions in this instruction
manual and make sure that they are also observed when operating the appliance via the Home Connect app. “Safety”, Page 2 ¡ Operating the appliance on the appliance itself always takes priority. During this time it is not possible to operate the appliance using the Home Connect app. ¡ In networked standby mode, the appliance requires a maximum of 2 W. ¡ If you need your device’s MAC address to connect to your home network, you can find this next to the rating plate. Page 12
7.1Setting up Home Connect
Requirements ¡ The appliance is connected to the power supply and
is switched on. ¡ You have a mobile device with a current version of
the iOS or Android operating system, e.g. a smartphone. ¡ The mobile device and the appliance are within range of your home network’s Wi-Fi signal. 1. Download the Home Connect app.

To set the air extraction mode, press .

2. Release

to save the setting.

6.21Switching on the audible signal
Requirement: The appliance is switched off. Press and hold and at the same time for ap-
prox. three seconds until a signal sounds.

2. Open the Home Connect app and scan the following QR code.

3. Follow the instructions in the Home Connect app.
7.2Resetting the connection
To reset the saved connections to the Wi-Fi and to Home Connect, press and hold and at the same time until goes out.
7.3Software update
Your appliance’s software can be updated using the software update function, e.g. for the purposes of optimisation, troubleshooting or security updates. To do this, you must be a registered Home Connect user, have installed the app on your mobile device and be connected to the Home Connect server. As soon as a software update is available, you will be informed via the Home Connect app and will be able to start the software update via the app. Once the update has been successfully downloaded, you can start installing it via the Home Connect app if you are in your local area network. The Home Connect app will inform you once installation is successful. Notes ¡ You can continue to use your appliance as normal
while updates are downloading. Depending on your personal settings in the app, software updates can also be set to download automatically. ¡ We recommend that you install security updates as soon as possible.

8

7.4Remote diagnostics
Customer Service can use Remote Diagnostics to access your appliance if you contact them, have your appliance connected to the Home Connect server and if Remote Diagnostics is available in the country in which you are using the appliance. Tip: For further information and details about the availability of Remote Diagnostics in your country, please visit the service/support section of your local website: www.home-connect.com
7.5Data protection
Please see the information on data protection. The first time your appliance is registered on a home network connected to the Internet, your appliance will transmit the following types of data to the Home Connect server (initial registration): ¡ Unique appliance identification (consisting of appli-
ance codes as well as the MAC address of the Wi-Fi communication module installed).
8 Hob-based hood control
You can connect your appliance to a suitable hob and, in this way, control the functions of your appliance via the hob. If both appliances are Home Connect- compatible, connect the appliances in the Home Connect app. To do this, connect the two appliances to Home Connect and follow the instructions in the app. Notes ¡ Regular security updates are provided for your ap-
pliance. If you have connected your extractor hood directly to a hob , both of these appliances cannot receive these security updates. To ensure the safe use of the appliance, we recommend connecting both appliances to each other via Home Connect and installing these updates as soon as they are provided. A Home Connect account (which is free of charge) is required for this.
9 Cleaning and servicing
To keep your appliance working efficiently for a long time, it is important to clean and maintain it carefully.
9.1Cleaning products
You can obtain suitable cleaning products from aftersales service or the online shop.
WARNING Risk of electric shock! An ingress of moisture can cause an electric shock. Before cleaning, pull out the mains plug or switch
off the fuse in the fuse box. Do not use steam- or high-pressure cleaners to
clean the appliance. WARNING Risk of burns!
The appliance becomes hot during operation. Allow the appliance to cool down before cleaning.

Hob-based hood controlen ¡ Security certificate of the Wi-Fi communication mod-
ule (to ensure a secure data connection). ¡ The current software and hardware version of your
appliance. ¡ Status of any previous reset to factory settings. This initial registration prepares the Home Connect functions for use and is only required when you want to use the Home Connect functions for the first time. Note: Please note that the Home Connect functions can only be utilised with the Home Connect app. Information on data protection can be retrieved in the Home Connect app.
¡ Please note the safety precautions in the instruction manual for your appliance and ensure that they are also observed when operating the appliance via the hob-based hood control.
¡ Operating your appliance always takes priority. It is not possible to use the hob-based hood control during this time.
¡ In networked standby mode, the appliance requires a maximum of 2 W.
¡ You can only connect to the extractor hood via the Home Connect app. Other connection routes are no longer supported.
ATTENTION! Unsuitable cleaning products may damage the surfaces of the appliance. Do not use harsh or abrasive detergents. Do not use cleaning products with a high alcohol
content. Do not use hard scouring pads or cleaning
sponges. Do not use any special cleaners for cleaning the ap-
pliance while it is hot. Only use glass cleaners, glass scrapers or stainless
steel care products if recommended in the cleaning instructions for the relevant part. Wash sponge cloths thoroughly before use.

9

enCleaning and servicing
9.2Cleaning the appliance
Clean the appliance as specified. This will ensure that the different parts and surfaces of the appliance are not damaged by incorrect cleaning or unsuitable cleaning products.
WARNING Risk of explosion! Highly caustic alkaline or highly acidic cleaning agents in conjunction with aluminium parts in the interior of the appliance may cause explosions. Never use highly caustic alkaline or highly acidic
cleaning agents. In particular, do not use commercial or industrial cleaning agents in conjunction with aluminium parts, e.g. grease filter on extractor hoods.
WARNING Risk of electric shock! An ingress of moisture can cause an electric shock. Before cleaning, pull out the mains plug or switch
off the fuse in the fuse box. Do not use steam- or high-pressure cleaners to
clean the appliance. WARNING Risk of burns!
The appliance becomes hot during operation. Allow the appliance to cool down before cleaning.
WARNING Risk of injury! Components inside the appliance may have sharp edges. Carefully clean the appliance interior. 1. Observe the information regarding the cleaning
agents. “Cleaning products”, Page 9 2. Clean as follows, depending on the surface: Clean stainless steel surfaces in the direction of
the finish using a sponge cloth and hot soapy water. Clean painted surfaces using a damp sponge cloth and hot soapy water. Clean aluminium using a soft cloth and glass cleaner. Clean plastic using a soft cloth and glass cleaner. Clean glass using a soft cloth and glass cleaner. 3. Dry with a soft cloth. 4. Apply a thin layer of the stainless steel cleaning product to stainless steel surfaces using a soft cloth. You can obtain stainless steel cleaning products from the after-sales service or the online shop.
9.3Cleaning controls
WARNING Risk of electric shock! Penetrating moisture may cause an electric shock. Do not use wet sponge cloths. 1. Observe the information regarding the cleaning
agents. “Cleaning products”, Page 9 2. Clean using a damp sponge cloth and hot soapy water. 3. Dry with a soft cloth.

9.4Removing the grease filter
WARNING Risk of injury! Risk of injury when opening and closing the hinges. Keep your hands away from the hinges. The filter cover may swing out. Open the filter cover slowly. Take hold of the filter cover after opening until it no
longer swings out. Close the filter cover slowly. 1. Take hold of the filter cover in the centre and open it
fully. 2. ATTENTION!
Falling grease filters may damage the hob below. Grip below the grease filter with one hand. Open the lock on the grease filter and fold down the grease filter.
3. Remove the grease filters from the holders. To prevent grease from dripping, hold the grease filter horizontally.
9.5Fitting the grease filters
1. ATTENTION! Falling grease filters may damage the hob below. Grip below the grease filter with one hand. Note: Note the correct position of the grease filter. Insert the grease filter.
2. The lock on the grease filter clicks into place.

10

Troubleshootingen

3. If the grease filter has been inserted incorrectly, carefully push the lock forwards, remove the grease filter and insert it correctly.
9.6Cleaning grease filters in the dishwasher
The grease filters filter the grease from the cooking vapour. Regularly cleaned grease filters guarantee a high level of grease removal. We recommend cleaning the grease filters every two months.
WARNING Risk of fire! Fatty deposits in the grease filters may catch fire. Clean the grease filters regularly. ATTENTION! The grease filters may become damaged if they are squeezed. Do not squeeze the grease filters. Note: When cleaning the grease filter in the dishwasher, light discolouration may occur. This discolouration has no effect on the performance of the metal grease filters.

Requirement: The grease filters have been removed. “Removing the grease filter”, Page 10 1. Observe the information regarding the cleaning
agents. “Cleaning products”, Page 9 2. Place the grease filters loosely into the dishwasher. Do not clean heavily soiled grease filters with utensils. Use special grease solvent for stubborn dirt. You can obtain grease solvents from after-sales service or the online shop. 3. Start the dishwasher. Select a temperature of no more than 70 °C. 4. Allow the grease filters to drain.
9.7Cleaning grease filters manually
The grease filters filter the grease from the cooking vapour. Regularly cleaned grease filters guarantee a high level of grease removal. We recommend cleaning the grease filters every two months.
WARNING Risk of fire! Fatty deposits in the grease filters may catch fire. Clean the grease filters regularly. Requirement: The grease filters have been removed. “Removing the grease filter”, Page 10 1. Observe the information regarding the cleaning
agents. “Cleaning products”, Page 9 2. Soak the grease filter in hot soapy water. Use special grease solvent for stubborn dirt. You can obtain grease solvents from after-sales service or the online shop. 3. Use a brush to clean the grease filters. 4. Rinse the grease filters thoroughly. 5. Allow the grease filters to drain.

10 Troubleshooting
You can rectify minor faults on your appliance yourself. Read the troubleshooting information before contacting after-sales service. This will avoid unnecessary costs.
WARNING Risk of injury! Improper repairs are dangerous. Repairs to the appliance should only be carried out
by trained specialist staff. If the appliance is defective, call Customer Service.

WARNING Risk of electric shock! Incorrect repairs are dangerous. Repairs to the appliance should only be carried out
by trained specialist staff. Only use genuine spare parts when repairing the
appliance. If the power cord of this appliance is damaged, it
must be replaced by trained specialist staff.

10.1Malfunctions

Fault The appliance is not working.

Cause and troubleshooting
The mains plug of the power cord is not plugged in. Connect the appliance to the power supply. The circuit breaker in the fuse box has tripped. Check the circuit breaker in the fuse box. There has been a power cut. Check whether the lighting in your kitchen or other appliances are working.

11

enDisposal

Fault The LED lighting does not work.
The button illumination does not work. Home Connect is not working properly. The hob-based hood control is not working properly.

Cause and troubleshooting
Different causes are possible. Defective LED lights may be replaced by the manufacturer, their customer service or a
qualified technician (electrician) only. Call the after-sales service.
“Customer Service”, Page 12
The control unit is faulty. Call the after-sales service.
“Customer Service”, Page 12
Different causes are possible. Go to www.home-connect.com. It may be necessary to change the settings. Read the instruction manual for the hob. Go to www .home-connect.com.

11 Disposal
11.1Disposing of old appliance
Valuable raw materials can be reused by recycling. 1. Unplug the appliance from the mains. 2. Cut through the power cord. 3. Dispose of the appliance in an environmentally
friendly manner. Information about current disposal methods are available from your specialist dealer or local authority.

This appliance is labelled in accordance with European Directive 2012/19/EU concerning used electrical and electronic appliances (waste electrical and electronic equipment – WEEE). The guideline determines the framework for the return and recycling of used appliances as applicable throughout the EU.

12 Customer Service
Function-relevant genuine spare parts according to the corresponding Ecodesign Order can be obtained from Customer Service for a period of at least 10 years from the date on which your appliance was placed on the market within the European Economic Area. Note: Under the terms of the manufacturer’s warranty the use of Customer Service is free of charge. Detailed information on the warranty period and terms of warranty in your country is available from our aftersales service, your retailer or on our website. If you contact Customer Service, you will require the product number (E-Nr.) and the production number (FD) of your appliance.
13 Accessories
You can buy accessories from the after-sales service, from specialist retailers or online. Only use original accessories, as these have been specifically designed for your appliance. Accessories vary from one appliance to another. When purchasing accessories, always quote the exact product number (E no.) of your appliance. Page 12

The contact details for Customer Service can be found in the enclosed Customer Service directory or on our website.
12.1Product number (E-Nr.) and production number (FD)
You can find the product number (E-Nr.) and the production number (FD) on the appliance’s rating plate. Depending on the model, the rating plate can be found: ¡ Inside the appliance (remove grease filters for ac-
cess). ¡ On top of the appliance. Make a note of your appliance’s details and the Customer Service telephone number to find them again quickly.

You can find out which accessories are available for your appliance in our catalogue, in the online shop or from our after-sales service. www.bosch- home.com

Accessories Standard circulated air set (flat hood)

Order number DWZ0AF0U0

12

Declaration of Conformityen

Accessories Standard no-flue circulated air set (flat hood) Standard odour filter (replacement, flat hood) Standard circulated air set (angled canopy hood) Standard no-flue circulated air set (angled canopy hood) Standard odour filter (replacement, angled canopy hood) Long Life circulated air set (flat hood) Long Life circulated air set (angled canopy hood) Long Life no-flue circulated air set (flat hood) Long Life no-flue circulated air set (angled canopy hood)

Order number DWZ0AF0T0 DWZ0AF0A0 DWZ0AK0U0 DWZ0AK0T0
DWZ0AK0A0
DWZ0AF0S0 DWZ0AK0S0 DWZ0AF0R0 DWZ0AK0R0

Accessories

Order number

Long Life odour filter (re- DZZ0XX0P0 placement)

Clean Air Plus circulated DWZ1AF1I6 air set (flat hood)

Clean Air Plus no-flue cir- DWZ1AF1V6 culated air set (flat hood)

Clean Air Plus circulated air set (angled canopy hood)

DWZ1AK1I6

Clean Air Plus no-flue cir- DWZ1AK1V6 culated air set (angled canopy hood)

Clean Air Plus circulated DWZ1AX5C6 air set, external

Clean Air Plus odour filter DWZ1AK1B6 (replacement)

Clean Air Plus odour filter DWZ1AF1B6 (replacement, flat hood)

Clean Air Plus odour filter DZZ1XX1B6 (replacement, angled canopy hood)

14 Declaration of Conformity

BSH Hausgeräte GmbH hereby declares that the appliance with Home Connect functionality conforms to the basic requirements and other relevant provisions of Directive 2014/53/EU. A detailed RED Declaration of Conformity can be found online at www.bosch-home.com among the additional documents on the product page for your appliance. Hereby, BSH Hausgeräte GmbH declares that the appliance with Home Connect functionality is in compliance with relevant statutory requirements.1

A detailed Declaration of Conformity can be found online at www.bosch- home.co.uk among the additional documents on the product page for your appliance.1
Only applies to Great Britain 2.4 GHz band (2400­2483.5 MHz): Max. 100 mW 5 GHz band (5150­5350 MHz + 5470­5725 MHz): Max. 100 mW

BE

BG

CZ

DK

DE

EE

FR

HR

IT

CY

LI

LV

MT

NL

AT

PL

PT

RO

SE

NO

CH

TR

IS

UK (NI)

5 GHz WLAN (Wi-Fi): For indoor use only.

IE

EL

ES

LT

LU

HU

SI

SK

FI

AL

BA

MD

ME

MK

RS

UK

UA

5 GHz WLAN (Wi-Fi): For indoor use only.

15 Installation instructions
Observe this information when installing the appliance.

1 Only applies to Great Britain 13

enInstallation instructions

15.1Scope of delivery
After unpacking all parts, check for any damage in transit and completeness of the delivery.

For Australia and New Zealand the minimum safety clearance above electrical cooktops must be 600 mm.
15.3Appliance dimensions
You will find the dimensions of the appliance here

15.2Safety clearances
Comply with the safety clearances for the appliance.

14

15.4Installation recommendation
We recommend fitting the appliance such that the lower edge of the glass screen is in line with the lower edges of the adjacent wall-hung cabinets.

B

B

Maintain the safety clearances to the hob. Page 14
15.5Secure installation Follow these safety instructions when installing the appliance.
WARNING Risk of poisoning! Risk of poisoning from flue gases being drawn back in. Room-air-dependent heat-producing appliances (e.g. gas, oil, wood or coaloperated heaters, continuous flow heaters or water heaters) obtain combustion air from the room in which they are installed and discharge the exhaust gases into the open through an exhaust gas system (e.g. a chimney). With the extractor hood switched on, air is extracted from the kitchen and the adjacent rooms. Without an adequate supply of air, the air pressure falls below atmospheric pressure. Toxic gases from the flue or the extraction shaft are sucked back into the living space.

Installation instructionsen
whenever the air needed for combustion is able to enter through openings that cannot be sealed, for example in doors, windows, incoming/exhaust air wall boxes or by other technical means. An incoming/exhaust air wall box alone does not ensure compliance with the limit. In any case, consult your responsible chimney sweep. They are able to assess the house’s entire ventilation setup and will suggest the suitable ventilation measures to you. Unrestricted operation is possible if the appliance is operated exclusively in circulating- air mode. Risk of poisoning from flue gases being drawn back in. If an extractor hood with an open-flued heat production source is installed, the power supply for the extractor hood must be provided with a suitable safety switch. Risk of poisoning from flue gases being drawn back in. Do not emit the exhaust air into a smoke or exhaust gas flue that is in operation. Do not emit the exhaust air into a shaft that is used to ventilate installation rooms for heat-producing appliances. If the exhaust air is to be conveyed into a smoke or exhaust gas flue, you must obtain the consent of the heating engineer responsible.
WARNING Risk of suffocation! Children may put packaging material over their heads or wrap themselves up in it and suffocate. Keep packaging material away from chil-
dren. Do not let children play with packaging ma-
terial.

Always ensure adequate fresh air in the room if the appliance is being operated in exhaust air mode at the same time as a room-air-dependent heat- producing appliance is being operated.
It is only possible to safely operate the appliance if the pressure in the room in which the heating appliance is installed does not drop more than 4 Pa (0.04 mbar) below atmospheric pressure. This can be achieved

15

enInstallation instructions
WARNING Risk of fire! Grease deposits in the grease filter may catch fire. The specified safety clearances must be
complied with in order to prevent a build-up of heat. Observe the specifications for your cooking appliances. If the installation instructions for the cooking appliances specify a different clearance, the larger of the two must always be provided for. If gas hobs and electric hobs are operated together, the largest specified clearance applies. The appliance must be installed with no more than one side directly next to a highsided unit or a wall. The distance between the appliance and wall or high-sided unit must be at least 50 mm. Grease deposits in the grease filter may catch fire. Never work with naked flames close to the appliance (e.g. flambéing). Do not install the appliance near a heatproducing appliance for solid fuel (e.g. wood or coal) unless a closed, non-removable cover is available. There must be no flying sparks.
WARNING Risk of injury! Components inside the appliance may have sharp edges. Wear protective gloves. The appliance may fall down if it has not been properly fastened in place. All fastening components must be fixed
firmly and securely in place. Risk of injury from glass splinters. Protect the filter cover against impact. Do not drop the filter cover. Wear protective goggles during installation. The appliance is heavy. The appliance must not be fitted directly
onto plasterboard or similar lightweight materials. To ensure correct installation, you must use a material which is sufficiently stable and suitable for both the structural conditions and the weight of the appliance. Changes to the electrical or mechanical assembly are dangerous and may lead to malfunctions. Do not make any changes to the electrical or mechanical assembly.
16

The filter cover may swing out. Open the filter cover slowly. Take hold of the filter cover after opening
until it no longer swings out. Close the filter cover slowly. Risk of injury when opening and closing the hinges. Keep your hands away from the hinges.
WARNING Risk of electric shock! Sharp-edged components inside the appliance may damage the connecting cable. Do not kink or trap the connecting cable. If the appliance or the power cord is damaged, this is dangerous. Never operate a damaged appliance. Never pull on the power cord to unplug the
appliance. Always unplug the appliance at the mains. If the appliance or the power cord is damaged, immediately unplug the power cord or switch off the fuse in the fuse box. Call customer services. Page 12 Incorrect repairs are dangerous. Repairs to the appliance should only be carried out by trained specialist staff. Only use genuine spare parts when repairing the appliance. If the power cord of this appliance is damaged, it must be replaced by trained specialist staff. Incorrect installation is dangerous. Connect and operate the appliance only in accordance with the specifications on the rating plate. Connect the appliance to a power supply with alternating current only via a properly installed socket with earthing. The protective conductor system of the domestic electrical installation must be properly installed. Never equip the appliance with an external switching device, e.g. a timer or remote control. When the appliance is installed, the mains plug of the power cord must be freely accessible. If free access is not possible, an all-pole isolating switch must be installed in the permanent electrical installation according to the conditions of Overvoltage Category III and according to the installation regulations.

When installing the appliance, check that the power cable is not trapped or damaged.
15.6Instructions for the electrical connection
In order to safely connect the appliance to the electrical system, follow these instructions.
WARNING Risk of electric shock! It must always be possible to disconnect the appliance from the electricity supply. The appliance must only be connected to a protective contact socket that has been correctly installed. The mains plug for the mains power cable must be
easily accessible after the appliance is installed. If this is not possible, an all-pole isolating switch
must be integrated into the permanent electrical installation according to the conditions of overvoltage category III and according to the installation regulations. The permanent electrical installation must only be wired by a professional electrician. We recommend installing a residual-current circuit breaker (RCCB) in the appliance’s power supply circuit. Sharp-edged components inside the appliance may damage the connecting cable. Do not kink or trap the connecting cable. ¡ The connection data can be found on the rating plate. Page 12 ¡ The connecting cable is approx. 1.30 m long. ¡ This appliance complies with the EC interference suppression regulations. ¡ The appliance corresponds to protection class 1. You should therefore only use the appliance with a protective earth connection. ¡ Do not connect the appliance to the power supply during installation. ¡ Ensure that the protection against contact is guaranteed during installation.
15.7Information on the installation situation
¡ Install this appliance on the kitchen wall. ¡ To install additional special accessory parts, ob-
serve the enclosed installation instructions. ¡ The appliance must be installed with no more than
one side directly next to a high-sided unit or a wall. The distance between the appliance and wall or high-sided unit must be at least 50 mm. ¡ The width of the extractor hood must correspond at least with the width of the hob. ¡ To optimally detect the cooking vapours, install the appliance in the middle of the hob. Air extraction mode ¡ If you operate the appliance in air extraction mode, a flue cover must be installed. Circulating-air mode ¡ If you are operating the appliance in circulating-air mode, an optional accessory must be fitted. To do this, refer to the installation instructions provided. ¡ For operation in circulating-air mode, the installation of the flue cover is optional.

Installation instructionsen
15.8General information
Follow these general instructions during the installation. ¡ For the installation, observe the currently valid build-
ing regulations and the regulations of the local electricity and gas suppliers. ¡ When discharging the exhaust air, the official and legal regulations, such as the regional building code., must be observed. ¡ In order to freely access the appliance for servicing, select an easy-to-reach installation site. ¡ The surfaces of the appliance are sensitive. Avoid damaging them during installation.
15.9Installation Checking the wall
1. Check whether the wall is horizontal and adequately load-bearing. The max. weight of the appliance is 40 kg.
2. Drill the hole depth in accordance with the length of the screws.
3. Use the enclosed screws and wall plugs. The screws and wall plugs enclosed are suitable for use with solid brickwork. Use suitable fastening parts for other structures, e.g. plasterboard, porous concrete, poroton bricks.
4. Install the appliance with a fixing material which is sufficiently stable and has been adjusted accordingly for both the structural conditions and the weight of the appliance.
5. Check the cut-out area for existing cables of other appliances.
Preparing the wall 1. Observe the information on the installation situation.
Page 17 2. Ensure that there are no electrical wires, gas pipes
or water pipes in the area where holes are to be drilled. 3. Cover the hob to prevent damage. 4. Determine the position of the extractor hood and lightly mark where the lower edge of the appliance should be on the wall. Determine the centre of the hob. Comply with the safety clearances for the hob.
Page 14 We recommend fitting the extractor hood such that the lower edge of the glass screen is in line with the lower edges of the adjacent wall-hung cabinets. 5. Place the template against the line drawn on the wall and secure it in place. 6. Mark the positions for the screws. 7. For the installation with the flue cover, separate the template along the marked cut line. 8. Drill the 8 mm diameter holes to a depth of 80 mm for the fastenings. 9. Remove the template. 10. Insert the wall plugs flush with the wall.

17

enInstallation instructions

2. Use a spirit level to align the appliance bracket horizontally and screw it firmly in place.

Variant A: Flat extractor hood with flue cover Variant B: Sloped extractor hood with flue cover

Installing the appliance 1. Remove the protective film from the rear.
Once the appliance is installed, fully remove the protective film.
2. Hook the appliance into the appliance bracket in such a way that it clicks firmly into place.
3. To align the appliance, slide the appliance to the right or to the left as required.
4. Tighten the safety screws.

Variant A: Flat extractor hood without flue cover
Variant B: Sloped extractor hood without flue cover Installing the appliance bracket 1. Screw on the appliance bracket for the extractor
hood hand-tight. 18

When you install a flue cover, install the bracket and hold it in place while screwing it in tight.
Piping Air extraction mode ¡ If you operate the appliance in air extraction mode,
a flue cover must be installed. Circulating-air mode ¡ If you are operating the appliance in circulating-air
mode, an optional accessory must be fitted. To do this, refer to the installation instructions provided. ¡ For operation in circulating-air mode, the installation of the flue cover is optional. Note: If you are using an aluminium pipe, smooth the connection area beforehand. We recommend the piping with an exhaust air pipe diameter of 150 mm.
Establishing the exhaust air connection (exhaust pipe, 150 mm diameter) 1. Secure the exhaust pipe to the air pipe connector. 2. Establish the connection to the exhaust air opening. 3. Seal the joints.

Establishing the exhaust air connection (exhaust pipe, 120 mm diameter) 1. Secure the reducing connector to the air-pipe con-
nector. 2. Secure the exhaust pipe to the air pipe connector. 3. Establish the connection to the exhaust air opening. 4. Seal the joints. Installing the flue duct
WARNING Risk of injury! Components inside the appliance may have sharp edges. Wear protective gloves.
WARNING Risk of electric shock! Sharp-edged components inside the appliance may damage the connecting cable. Do not kink or trap the connecting cable. 1. Screw the retaining bracket for the flue duct to the
wall. 2. To separate the flue ducts, remove the adhesive
tape or the flue duct from the protective packaging. 3. Remove any protective foil from both flue ducts. 4. Note: The slots on the flue duct should point down-
wards. Use the 2 screws to screw the upper flue duct to the sides of the retaining bracket.
5. Note: To prevent scratches, lay soft towels over the edges of the outer flue duct to protect the surface. Place the lower flue duct on the appliance and pull it slightly apart.
6. Put the lower flue duct over the upper flue duct.
7. Clip the lower flue duct onto the lower retaining bracket. Ensure that the connecting cable is not trapped.
8. Carefully remove the towels.

Installation instructionsen 19

Thank you for buying a Bosch Home Appliance!
Register your new device on MyBosch now and profit directly from: · Expert tips & tricks for your appliance · Warranty extension options · Discounts for accessories & spare-parts · Digital manual and all appliance data at hand · Easy access to Bosch Home Appliances Service Free and easy registration ­ also on mobile phones: www.bosch-home.com/welcome

Looking for help? You’ll find it here.
Expert advice for your Bosch home appliances, help with problems or a repair from Bosch experts. Find out everything about the many ways Bosch can support you: www.bosch-home.com/service Contact data of all countries are listed in the attached service directory.

BSH Hausgeräte GmbH Carl-Wery-Straße 34 81739 München, GERMANY www.bosch- home.com A Bosch Company
9001640373
9001640373(020721) en

Valid within Great Britain: Imported to Great Britain by BSH Home Appliances Ltd. Grand Union House Old Wolverton Road Wolverton, Milton Keynes MK12 5PT United Kingdom

References

• Home Appliances Global Website | Bosch
• Bosch home appliances: Experience quality, reliability and precision | Bosch UK
• Home Appliances Global Website | Bosch
• Bosch Service | Service worldwide
• Welcome to MyBosch
• Connect your household | Home Connect

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>