TTCIOTSDK KA-HY-254104 V8DC Bluetooth BLE V4.0 UART Module User Manual

June 9, 2024
TTCIOTSDK

TTCIOTSDK KA-HY-254104 V8DC Bluetooth BLE V4.0 UART Module User Manual

Copyright © 2010-2019 SHENGRUN Technology Co., Ltd.
All rights reserved.

SHENGRUN Technologies assumes no responsibility for any errors  which may appear in this manual, Furthermore, SHENGRUN Technologies reserves the right to alter the hardware,  software, and/or specifications detailed here at any time without notice and does not make any commitment to update the information contained here. SHENGRUN’s products are not authorized for use as critical components in life support devices or systems. SHENGRUN Technologies assumes no responsibility for any patents or authorized the use of intellectual property rights.

The Bluetooth trademark is owned by the Bluetooth SIG Inc., USA

Description

KA-HY-254104 Bluetooth low energy UART protocol module is a single mode device targeted for low power sensors and accessories.

KA-HY-254104 offers all Bluetooth low energy features: radio, stack, profiles and application space for customer applications. The module also provides flexible hardware interfaces to connect sensors.

KA-HY-254104 can be powered directly with a standard 3V coin cell batteries or pair of AAA batteries. in lowest power shutdown mode it consumes only 0.5 uA and will wake up in few microseconds.

Bluetooth IC :TTC2541 660.9mm 40pin IC / use TI CC2541 IC dice

KA-HY-254104 V8DC with shield case and Pre-certified RF regurations for blue tooth BQB, And can Compliance for worldwide RF Regulations, ex: Japan, Korea, CE ETSI RED, FCC etc….

APPLICATIONS:

  • Heart rate sensors
  • Pedometers
  • Watches
  • Blood pressure and glucose meters
  • Weight scales
  • Key fobs
  • Households sensors and collector devices
  • Security tags
  • Wireless keys (keyless go)
  • Proximity sensors
  • ndoor GPS broadcasting devices

KEY FEATURES:

  • Bluetooth BLE v.4.0 single mode compliant
  • Supports master, slave nd master/slave modes
  • Integrated Bluetooth low energy stack
  • GAP, GATT, L2CAP, SMP Bluetooth low energy profiles
  • Compliance: BQB BLE4.0, FCC, IC(Canada), CE ETSI RED etc. worldwide RF Regulations.
  • In-System-Programmable Flash 256KB SRAM 8KB
  • Low current consumption :Shutdown. No clocks running, no retention: 0.5uA(Typical)

KA-HY-254104 V8DC Metal wire Antenna PCBA with shield case dimension size

and picture

Module pin definition and description of input and output ports

**KA-HY-254104(Metal wire Antenna PCBA pin map and MIC ID & Lable mark

**

Pin function table

pin No Function Descrip. Function corresponds
1 REST BLE hardware reset pin (Low: reset)
2 RX UART Serial data bus input
3 TX UART Serial data bus output
4 WAKEUP BLE wake up pin: Low/ wake up, High / BLE module automatically

sleep
5| INT| Interrupt output pin
6| GND| BLE module grounding pin
7| VCC| BLE module power supply pin, voltage range of 2.0 ~ 3.6V

  • A: UART: serial bus, the default baud rate 115200bps, a single packet transmission is less than 17 bytes, package transmission intervals greater than 20ms.
  • b:WAKEUP: BLE wake up pin, Low _wake up, High/ BLE module automatically sleep.
  • C: RESET: BLE hardware reset pin, Low level reset.
  • d: VCC : BLE module power supply pin voltage range DC 2.0~3.6V.
  • e: GND: BLE module ground pin.

Electrical Characteristics

General Characteristics

(With Ta = 25 ℃, VDD = 3.0V, standard measure:1Mbps , 250KHz GFSK modulation Bluetooth Low energy mode.)

  1. Modulation Mode: GFSK;
  2. Frequency range: 2402~2480MHZ (2.4G ISM band);
  3. RF transmit power setting Range: -20 ~ +0 dBm ( programmable by software)
  4. The antenna feedpoint RF transmit power : -3dBm typical. (TX set Max.output characteristics)
  5. T h e antenna feed point RF receiver sensitivity : -84dBm typical. ( PER <30.8%)
  6. Operating ambient temperature range: -40 ℃ ~ + 85 ℃;
  7. The storage temperature range: -40 ℃ ~ + 125 ℃;
  8. The power supply voltage: 2.2 ~ 3.6VDC;
  9. Receiving mode current (high gain setting): 20.02 mA (typical);
  10. Transmit mode current ( at 0dBm output setting ): 18.2 mA (typical);
  11. MCU law active current (only 32MHz operation of X-tal OSC) : 6.7 mA (typ);
  12. Power mode 1: The current consumption: (under MCU standby mode, the wake-up time = 4uS); I= 270uA (Typical);
  13. Power mode 2: THE current consumption in sleep mode. timer activate / enable, wake-up time can by the programming software setting): I = 1uA (typ);
  14. Power mode 3: The current consumption 🙁 Low power deep sleep mode, via the hardware initiative wake ): I = 0.5uA(Typical);

Absolute Maximum Ratings

Note: These are absolute maximum ratings beyond which the module can be permanently damaged, these are not Maximum operating conditions, the maximum recommended operating conditions are in the table 4-4

Rating Min Max Unit
VDDS -0.3 3.9 V
Other Terminal Voltage VSS-0.3 VDDS+0.3 V
Storage Temperature 40 +125 °C

Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating Conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
ESD Ratings

| | | Value| Unit
---|---|---|---|---
V ESD Electrostatic discharge| Human body model (HBM), per ANSI/ESDA/JEDECJS001| All pins| ±2000| V
Charged device model (CDM), per JESD22-C101| RF pins| ±750
| Non-RFpins| ±750

CAUTION: ESD sensitive device. Precautions should be used when handing the device in order to prevent permanent damage.

Recommended Operating Conditions

Supply voltage noise should be less than 10mVpp. Excessive noise at the supply voltage will reduce the RF performance.

Note

  1. VDD power supply recommended voltage : 2.7~3.3V
  2. When programming firm ware , the VDD supply voltage must in DC 2.4~3.3V, To avoid programming has not completely, or abnormal status occur..
  3. For smaller coin cell batteries, with high worst-case end-of-life  equivalent source resistance, a 22-μF VDDS input capacitor must be used to ensure compliance with this slew rate(6-6 timing req.).

Block Diagram

Functional Block Diagram

Working mode schematic

Metal wire antenna characteristics

Antenna Gain : 2.657dB at 2440MHz

Syn the tizer: Set Frequency| Gain . dBi| Efficiency(%)| Efficiency(dB)
---|---|---|---
2402| 2.44| 54.50%| -2.636

  • Antenna size

8-4. Phi = 0 degree pattern

  • 8-2. 3D Radiation Pattern

8-5. Phi = 90 degree pattern

  • 8-3. X / Y / Z coordinate

8-6. Theda = 90 degree

**pattern

**

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions. may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on. the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help. To assure continued compliance, any changes or modifications not expressly approved by the party. Responsible for compliance could void the users authority to operate this equipment_ (Example- use only shielded interface cables when connecting to computer or peripheral devices).

This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

  1. This device may not cause harmful interference. and
  2. This device must accept any interference received, including interference that may cause undesired operation.

FCC Radiation Exposure Statement: The equipment complies with FCC Radiation exposure limits set forth for uncontrolled enviroment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.

The following information is shown in the user’s manual.

Compliance Information

Product Name: Model Number: Trade name:| Bluetooth module KA- HY-254104/
---|---
Compliance Statement:| This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Correspondence of the responsible party in USA:
Company:| Kickass Products USA LLC
Address:| 9070 IRVINE CTR DR, STE. 135, IRVINE, USA 92618
Tel.:| 213 652 6566

The user manual shall include the following or similar statement, placed in a prominent location in the text of the manual:

Warning: Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Class B device:
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

MPE caution (if a FCC certified RF module is inserted in & the separation distance is indicated in the FCC grant of RF module)

To satisfy FCC / IC RF exposure requirements, a separation distance of 20 cm or more should be maintained between the antenna of this device and persons during device operation. To ensure compliance, operations at closer than this distance is not recommended.

V1.0www.tuner168.com

Copyright © 2010-2019 SHENGRUN Technology Co., Ltd.
All rights reserved. SHENGRUN Technologies assumes no responsibility for any errors which may appear in this manual, Furthermore, SHENGRUN Technologies reserves the right to alter the hardware, software, and/or specifications detailed here at any time without notice and does not make any commitment to update the information contained here. SHENGRUN’s products are not authorized for use as critical components in life support devices or systems. SHENGRUN Technologies assumes no responsibility for any patents or authorized the use of intellectual property rights. The Bluetooth trademark is owned by the Bluetooth SIG Inc., USA

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals