Schneider Electric LV485500 Interface Kit, Pact Series Circuit Breakers Instruction Manual
- June 9, 2024
- Schneider Electric
Table of Contents
- Schneider Electric LV485500 Interface Kit, Pact Series Circuit Breakers
- Required for Installation
- Description
- Installation
- Power Supply
- Service Interface + MasterPact NT/NW
- Service Interface + ComPacT NSX,
- Description of the LEDs
- Manufacturing Date
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
Schneider Electric LV485500 Interface Kit, Pact Series Circuit Breakers
Master PactTM NT/NW
www.se.com
U G Service Interface
DOCA0170EN
LV485500 Service Interface
Retain instruction sheet for future use.
Visit our website at www.se.com to download the
documents listed above (user guides U G ) and other documents.
PLEASE NOTE
- Electrical equipment should be installed, operated, serviced, and maintained only by qualified personnel.
- No responsibility is assumed by Schneider Electric for any consequences arising out of the use of this material.
- All pertinent state, regional, and local safety regulations must be observed when installing and using this product.
DANGER
HAZARD OF ELECTRIC SHOCK, EXPLOSION OR ARC FLASH
- Apply appropriate personal protective equipment (PPE) and follow safe electrical work practices. See NFPA 70E, CSA Z462, NOM-029-STPS or local equivalent.
- This equipment must only be installed and serviced by qualified electrical personnel.
- Turn off all power supplying this equipment before working on or inside equipment.
- Always use a properly rated voltage sensing device to confirm power is off.
- Replace all devices, doors, and covers before turning on power to this equipment.
Failure to follow these instructions will result in death or serious injury.
WARNING: This product can expose you to chemicals including lead and lead
compounds, which are known to the State of California to cause cancer and
birth defects or other reproductive harm.
For more information go to
www.P65Warnings.ca.gov.
Required for Installation
Description
Service Interface
- A 24 Vdc power input
- B 24 Vdc power output
- C Mini USB port
- D Test port LED
- E Status LED
- F USB LED
- G QR code for product information
- H Power LED
- I Magnetic Service Interface holder
- J Test port
- K Rubber protective cover
- L Magnetic cable holder
Accessories
- A AC/DC power.
- B 7-pin cable for 630–6300 A ACB MCCB trip units.
- C 7-pin cable for 100–630 A MCCB trip units.
- D ULP cable.
- E USB cable with magnet.
- F 24 Vdc power output connector.
Installation
Power Supply
Use the AC/DC power LV485511SP to supply the Service Interface.
- The Service Interface can power one Enerlin ‘X device up to 120 mA.
Service Interface + MasterPact NT/NW
Service Interface + ComPacT NSX,
Description of the LEDs
Test Port LED
- No MicroLogic trip unit connected
- MicroLogic trip unit connected
Power LED
- Power input not connected
- Power input connected
USB LED
- No USB connected
- USB connected
Status LED
- Service Interface non-operational
- Service Interface out of calibration
- Service Interface in Boot mode
Manufacturing Date
The product’s manufacture date is coded PPYYWWDXXXX, where:
- PP: plant code
- YY: year of manufacture
- WW: week of manufacture
- D: weekday of manufacture (Monday = 1)
- XXXX: Serial number
Eg: HL190320640 = product manufactured at plant HL on Tuesday 15 January 2019 with serial number 0640.
Schneider Electric Industries SAS 35, rue Joseph Monier
CS 30323
F – 92506 Rueil Malmaison Cedex www.se.com
GDE78167-01
© 2022 Schneider Electric – All rights reserved.