NATIONAL GEOGRAPHIC 9683500 4K Ultra-HD WIFI Action Camera Explorer 6 User Manual

NATIONAL GEOGRAPHIC 9683500 4K Ultra-HD WIFI Action Camera Explorer 6

FULL MANUAL DOWNLOAD:

http://www.bresser.de/download/9683500

APP DOWNLOAD „iSmart DV“:

SERVICE AND WARRANTY:

www.bresser.de/warranty_terms

About this Instruction Manual

Please read the safety instructions and the operating instructions carefully before use. Keep these instructions for renewed use at a later date. When the device is sold or given to someone else, the instruction manual must be provided to the new owner/user of the product.

Intended Use
This product is intended only for private use. It was developed as an electronic medium for the use of multimedia services.

General Warnings

• Risk of choking — Keep packaging material, like plastic bags and rubber bands, out of the reach of children, as these materials pose a choking hazard. This product contains small parts that could be swallowed by children.

• Leaking battery acid can lead to chemical burns. Avoid contact of battery acid with skin, eyes and mucous membranes. In the event of contact, rinse the affected region immediately with a plenty of water and seek medical attention.

• Risk of electric shock — Never bend, pinch or pull the power and connecting cables, extensions and adapters. Protect the cables from sharp edges and heat.Before operating, check the device,  cables and connections for damage. Never use a damaged unitor a unit with damaged power cables. Damaged parts must be exchanged immediately by an authorised service centre.

• Risk of property damage! — Do not disassemble the device.
  In the event of a defect, please contact your dealer. The dealer will contact the Service Centre and can send the device in to be repaired, if necessary.

• Do not expose the device to high temperatures. Do not shortcircuit the device or throw them into a fire. Excessive heat or improper handling could trigger a short-circuit, a fire or an explosion.

• Do not interrupt an on-going data connection to a computer before all data has been transferred. This could lead to data loss for which the manufacturer is not liable.

Notes on cleaning

• Turn off the camera
• Clean the eyepieces and/or lenses only with a soft, lint-free cloth, (e.g. microfibre cloth). To avoid scratching the lenses, use only gentle pressure with the cleaning cloth.
• Only use a dry cloth to clean the exterior of the device. To avoid damaging the electronics, do not use any cleaning fluid.
• Clean the protective case after each use with clear, clean water and dry it thoroughly

EC Declaration of Conformity

 Bresser GmbH has issued a “Declaration of Conformity”
in accordance with applicable guidelines and corresponding standards. The full text of the EU declaration of
conformity is available at the following internet address:
www.bresser.de/download/9683500/CE/9683500_CE.pdf

Disposal
Dispose of the packaging materials properly, according to their type, such as paper or cardboard. Contact your local waste-disposal service or environmental authority for information on the proper disposal.
Do not dispose of electronic devices in the household garbage!
As per the Directive 2012/19/EC of the European Parliament on waste electrical and electronic equipment and its adaptation into German law, used electronic devices must be collected separately and recycled in an environmentally friendly manner. Empty, old batteries must be disposed of at battery collection points by the consumer. You can find out more information about the disposal of devices or batteries produced after 6 January 2006 from your local waste-disposal service or environmental authority.

The integrated battery must only be removed for disposal.
Opening the device housing can damage the unit.
Drain the battery completely before disposal. Remove all the screws in the housing and open the device housing. Remove the connections to the battery and remove it. Cover the open contacts with tape and package the battery in such a way that it cannot shift in the packaging.

Warranty & Service
The regular guarantee period is 5 years and begins on the day of purchase. You can consult the full guarantee terms and details of our services at www.bresser.de/warranty_terms.

Scope of delivery

1. Camera
2. Camera housing and belt clip
3. Bicycle mount
4. Thumb knobs
5. Retaining clip for Base mount
6. Multifunction mount
7. Base for flat surface + sticker
8. USB cable
9. 1/4” Tripod adapter (male/female) and straps
10. Battery pack and spare battery pack

First Steps

**Inserting Micro SD card***

• Class 10 SDHC or higher required
• Capacity up to 128 GB
• To remove: Press the Micro SD card with your fingernail. The card pops out.

Note: For best performance, please choose a branded Micro SD card and format it on your computer before use. Unbranded cards are not guaranteed to work flawlessly.
*Micro SD card not included

Installing or removing the battery

• A. Open the battery cover.
• B. Correctly install the battery into the camera.
• C. Close the battery cover.
  

Charging

• A. Charging can be done by connecting the action camera to a computer via the usb cable.
• B. Charging of the action camera can be done even when it’s powered off. However, the camera cannot be switched on in this state. Therefore, first switch the camera on and then start the charging process.

Turning camera on and off
Press and hold the power switch for 3 to 5 seconds to turn the camera on or off

Functions

1. Lens

2. Cover

3. Micro USB port & Micro HDMI port
   

4. Charge indicator

5. Display

6. button & WIFI button

7. button
   

8. Power button (on/off) & Mode button

9. Hole for lanyard

10. Working indicator light

11. OK / Record button

12. Cover

13. Micro SD port & Battery cover

**How to use the Base mount

**

Base mount (e.g. for helmet mount):

Mount examples:

Base mount

Bicycle mount

Helmet mount

**Belt mount

**

Operating

A few short tips before you start:

• Remove the films from the lens and screen before use.
• In video mode: press the button to switch WIFI on/off.
• In photo mode: press and hold the button or button to zoom in/out on the photo.
• In photo mode: press the button to switch beauty photo on/off.

Press the [Power ON/OFF / Mode] button repeatedly to cycle through the camera modes.

| Video-Aufnahmemodus| | | Foto-Aufnahmemodus| | **| Playback and settings**
---|---|---|---|---|---|---|---

Playback and settings

Video Recording
Press and hold the [Power ON/OFF / Mode] button for 3 to 5 seconds to turn the camera on. There will be an  icon in the upper left corner. Insert a Micro SD card and start recording by pressing “OK” [EXPLORER 6]. Press “OK” [EXPLORER 6] again if you want to stop the recording.

Note:

• When recording video at high resolution or high frame rates such as 4K 30fps, the camera may become hot and consume more power, which is normal.
• When recording video at high frame rates above 60 fps, the video is recorded in slow motion.
• When you record video at high frame rates above 60 fps, EIS, time-lapse video and time-lapse are not automatically available.
• A FAT32 format micro SD card stops recording when the size of a file exceeds 4 GB, and then starts recording a new file.
  

Video settings
To access the video settings, press repeatedly until the video settings icon is selected. Now press “OK” [EXPLORER 6] to open the menu.

EV (Exposure): -3 ~ +3
By default, your camera uses the entire image to determine the appropriate exposure level. However, EV allows you to select a value that the camera will give priority to when determining exposure. This setting is especially useful for shots where an important area might otherwise be over- or under-exposed. If you change this setting, the LCD screen will immediately show you the effect on your image. When you leave this mode at “0”, the camera uses the entire scene again to determine the correct exposure.

EIS (Electronic image stabilisation) : On/Off
This camera is equipped with an EIS function with a 6-axis gyroscope to detect changes in motion. If the camera tilts, moves, shakes or shakes, the sensor uses a cross-border image compensation algorithm to compensate for the change and produce stable video, especially for activities with relatively small angles (about 6 degrees) but fast movements such as cycling, motorcycling and handheld applications.

Note:

• 1080P 60fps/720P 120fps, loop video, fast motion video, TL duration and slow motion are not supported by EIS!

Video loop: Off / 1min / 3min/ 5min

If the micro SD card is full, the new files will overwrite the old files if the video loop is on.

Note: EIS, Time Lapse Video, TL Duration, Slow Motion and Auto Low Light not automatically available.

Time-Lapse Video: Off / 1Sec. / 3Sec. / 5Sec. / 10Sec. /30Sec. /1min
The time-lapse video mode creates a video from frames shot at specified intervals.

Note:

• The time-lapse video is recorded without sound.
• If you select time-lapse video, the camera cannot record the video above 30fps.
• EIS, Video Loop, Slow Motion, Fast Motion and Auto Low Light are not automatically available

Time-Lapse Video (TL Duration): Unlimited/5Min / 10Min /15Min / 20Min/ 30Min / 60Min
Continuously creates a time-lapse video of a specified duration.

Note: If you want to set the duration of the time lapse, please switch on the time lapse video mode first.

FOV (Field of view): Wide / Medium / Narrow
The FOV refers to how much of the scene (measured in degrees) can be captured by the camera lens.

Auto Low Light: On / Off
The Auto Low Light mode automatically adjusts the brightness at to achieve the best performance in low light conditions.

Date stamp: Off / Date / Date & Time
When you turn on date stamp, the camera adds a date/time stamp to the videos you record.

Photo shooting
Switch to photo shooting mode by pressing [ ]. There will be an [ ] icon in the upper left corner. Press ”OK” [EXPLORER 6] to take a photo.
Switch to photo setting mode, for example, to activate time-lapse/burst mode /self-timer/long-term exposure, etc.

ISO: Auto / 100 / 200 / 400 / 800 / 1600 / 3200
ISO determines the light sensitivity of the camera and creates a compromise between brightness and resulting image noise. In low light, higher ISO values result in brighter images, but with greater image noise. Lower values result in lower noise levels, but darker images.

Time Lapse
The time-lapse function takes a series of photos at specified intervals. The camera emits a shutter sound each time a photo is taken.
With TL Duration, you can set a duration for the recording.

Burst Photo (Continuous shooting)
The camera triggers continuous shooting. The camera takes a series of 3 or up to 30 photos each time the shutter is activated.

Self Timer
The camera starts the countdown and emits a shutter sound when recording.

Long Exposure
Make sure that the Long Exposure option is enabled. The camera emits a shutter sound when a photo is taken.
Note: Time-lapse, continuous advance, self-timer and long time exposure cannot be selected at the same time. If you select one of these modes, the other three are not available.

Zoom function
The zoom function allows you to adjust how close or far away the subject appears in your photo. No zoom is set by default. The zoom function is only available in photo mode.

1. Turn on your camera.
2. Activate the photo mode.
3. Press and hold the or button to adjust the zoom level.

Save & Playback
When you are finished recording, you can transfer videos to your computer via USB cable. Connect the USB cable to the PC and camera and select “Transfer files”. Access to the SD card memory is now possible from the PC. You can also remove the Micro SD memory card and access the data through a card reader.

Playback on the camera:

1. Enter the video or photo playback mode. If the SD card contains a lot of contents, it may take a minute to load.
2. Press the or button to scroll through the video or photo files.
3. Press the “OK” [EXPLORER 6] button to open the video or photo in full screen mode.
4. Press the [ON/OFF] / Mode key to return to the file list.
5. To cancel the playback mode, press the [ON/OFF] / Mode button again.

Playback on the television set:

1. Switch on the television set.
2. Connect the micro HDMI end to the camera and the HDMI end to the HDMI on the television.
3. Wählen Sie die richtige Eingangsquelle am Fernseher.
4. Turn the camera on after a while. You can preview the camera from the TV.
5. Set the camera to the video/photo playback mode.
6. Select the desired content for playback.

Note:

• If the camera is connected to a television via an HDMI cable, you cannot record videos or photos, only playback.
• An HDMI cable is not included.

Play on the computer:

1. To play back your videos and photos on a computer, you must first transfer these files to a computer.
2. The transfer also frees up space on your micro-SD card for new content.
3. To transfer files to a computer using a card reader (sold separately) and your computer‘s File Explorer, connect the card reader to the computer, then insert the micro SD card.
4. You can now transfer files to your computer or delete selected files on your card.

Note:

• 4K requires a high data transmission rate. If you play back a 4K video file using a card reader, you may not be able to obtain sound. For better playback results, it is highly recommended that you copy the 4K video directly to your computer for playback.
• The Quick Time Player offers good compatibility with video files in MOV format. We strongly recommend using Quick Time Player to play video files on your computer.

Delete videos/photos
In video or photo playback mode, press the or button to select the file you want to delete. Press and hold the button for 3 seconds. The screen displays „Delete File“. Select the desired „Single File“ or „All Files“ option, and then press the „OK“ [ EXPLORER 6 ] button to select the desired option. Select „Yes“ and press the „OK“ [EXPLORER 6] button, or select „No“ to cancel the operation.

WIFI Mode / Camera App

With the WIFI app you can remote control your camera with a smartphone or tablet. Features include full camera control, live preview, playback and sharing of selected content and more.

First, install the app on your smartphone. Look for „iSmart DV“ in the AppStore or Google Play Store. Press and hold the button of the camera for 3 to 5 seconds to activate WIFI on the camera. Connect the camera to your smartphone (find a network with the name displayed on the camera e.g. „iSmart DV“). Use the displayed password, usually „1234567890“. Start the action camera app now. “Add New Camera” and then “Connect WIFI”.

Settings

To access the settings, press several times until you see the video playback icon is selected. Now press the button until the icon for the settings [ ] is selected. Now press “OK” [ EXPLORER 6] to open the menu.

In photography, the metering mode refers to the way a camera determines exposure. With cameras, the user can generally choose between the metering modes centre, average or spot metering. The different metering modes allow the user to select the most appropriate mode for use in different lighting conditions.

AWB (White Balance)| automatic / daylight / cloudy / bulb / fluorescent tube / snorkel / snow mode

White balance lets you adjust the colour temperature of videos and photos to optimise them for cool or warm lighting conditions.

Snorkel mode offers colour correction while shooting in blue water or clear fresh water at depths

of 5 to 33 feet (1.5 to 10 metres).

Snow mode can suppress overexposure in high brightness environments such as snowfields or beaches.

Effect| Standard / Black & White / Natural / Negative / Retro / Brightness Contrast
LDC (lens distortion correction)| Switch on the distortion correction function, it can correct the image distortion.
---|---
Date and time| YYMMDD 00:00:00
Screensaver| Off / 1min / 3min / 5min

Switches off the LCD after a period of inactivity to conserve battery power. To turn the LCD back on, press any key on the camera

Upside down| This setting determines the orientation of the setting menu.
Power off| Switches your camera off after a period of inactivity to conserve battery power.
WIFI| On / Off
Driving Mode| If you switch on the car mode and connect the camera to the car charger, the camera will automatically switch on and start recording when you start the engine of your car. The camera turns off and stops recording when you turn off the car engine.

Note:

•  A car charger with 5V 1A output must be used.

•  When used as a dashboard camera, we recommend that you switch on the loop video, car mode and screen saver at the same time.

Language| Specifies the language displayed on the camera.
Format| Reformatting will delete all your content. So make sure you download your photos and videos first. To reformat your card, press the mode button to access system settings, then press the down key several times to go to Format > Format Card? > YES.
Reset| This option resets all settings to their default values.
Version| Model / Version / Number / Date
Memory Card| This option allows you to check the capacity and free space of your micro-SD card.

Technical data

(120fps/60fps), 720P (240fps/120fps)
Video format| .MOV
Storage| Micro SD card up to 128 GB (not included) (SDHC Class 10 or higher required)
Shooting modes| Single recording / Loop recording / Time Lapse / TL- Duration / Burst mode / Self timer
Frequency| 50Hz/60Hz
Ports| Micro-USB, Micro-HDMI,  Micro SD card slot
Power source interface| 3.7 V
Battery capacity| 1050 mAh
WIFI| 2.4G,802.11 a/b/g/n
Dimensions| 63x33x46 mm
Weight| 95 g**

Note: Specifications could be subject to change due to upgrading or updating.
Please regard the actual product as the standard.

References

• Bresser | Startseite | Expand Your Horizon mit BRESSER
• Bresser | Startseite | Expand Your Horizon mit BRESSER
• index · powered by h5ai 0.26.1 (http://larsjung.de/h5ai/)

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>