ZEVNI A04658 Upend 10.2-Inch 1-Light Matte Gold LED Modern-Contemporary Vanity Light Installation Guide
- June 9, 2024
- ZEVNI
Table of Contents
ZEVNI A04658 Upend 10.2-Inch 1-Light Matte Gold LED Modern-Contemporary
Vanity Light
INSTALLATION INSTRUSTRUCT
Item Number: A04658
WARNING (To reduce the risk of fire, electric shock, or personal injury):
- We suggest installation by a licensed electrician.
- Please read the instruction carefully and save them as you may need them at a later time.
- Before you start, NEVER attempt any work without shutting off the electricity until the work is done.
- Go to the main fuse, or circuit breaker, box in your home.
- Place the main power switch in the “OFF” position.
- Place the wall switch in the “OFF” position.
- The mounting surface should be clean, dry, flat, strong enough, and 1/4” larger than the canopy on all sides. Any gaps between the mounting surface and canopy exceeding
- 3/16” should be corrected as required.
- Make sure that the ceiling or wall can stand the weight of the lamp before installation.
- Make sure the voltage you are using is 120V. The maximum wattage is 8W.
- Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp.
- When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.
- The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products.
IMAGE FOR FINISHED PRODUCT
TOOLS REQUIRED
(NOT INCLUDED):
Before starting assembly and installation please prepare the needed tools as
below picture
PARTS INCLUDING
- (C) Mounting plate (1)
- (D) Green ground screw (1)
- (E ) Backplate (1)
- (F) Stud (2)
- (G) Fixture body (1)
- (H) Lampshade (1)
ACCESSORIES ENCLOSED
- (A) Mounting screw (2)
- (B) Plastic wire connector (3)
ASSEMBLY & INSTALLATION INSTRUCTIONS
-
Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.
-
Turn off power
Before you start the installation, NEVER attempt any work without shutting off the electricity until the work is done. -
Go to the main fuse, or circuit breaker, box in your home.
-
Place the main power switch in the “OFF” position.
-
Place the wall switch in the “OFF” position
Make assembly
- Step A1 » Unscrew studs (F) from back plate (E), then set them aside for later installation.
- Step A2 » Carefully pass the supply wires from the outlet box through the mounting plate (C). Secure mounting plate (C) to the outlet box with mounting screws (A).
- Step A3 » Make wire connections Connect wires as below wires connection shown.
- PLEASE NOTE THAT GROUND WIRE IS BARE COPPER WIRE, NEVER CONNECT OTHER WIRES TO GROUND WIRES.
- Twist wires together with plastic wire connectors until tightly joined, and wrap each connector with approved electrical tape. Be sure that no wire strands are exposed and then carefully tuck all wires into the outlet box.
- Step A4 » Align the holes in back plate (E) and mounting plate (C), then secure them with the previously removed studs (F)
- Step A5» Check everything is installed properly, then you could turn on the light. Enjoy!
ORDERING PARTS.
- Keep this sheet for future reference in case you need to order replacement parts. All parts for this fixture can be ordered from the place of purchase. Be sure to use exact wording from illustrations when ordering parts.
CLEANING.
- To clean, wipe the fixture with a soft cloth. Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.
- +1 850 296 2377 Working hours: Mon – Fri 9:00 – 16:00 ESThomecustomercare@outlook.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>