ZEVNI A04656 Duran 3-Light 9-Inch Matte Black and Gold LED Flush Mount Light Installation Guide

June 9, 2024
ZEVNI

ZEVNI A04656 Duran 3-Light 9-Inch Matte Black and Gold LED Flush Mount

Light

Item Number: A04656

WARNING (To reduce the risk of fire, electric shock, or personal injury):

  1. We suggest installation by a licensed electrician.
  2. Please read the instruction carefully and save it as you may need it at a later time.
  3. Before you start, NEVER attempt any work without shutting off the electricity until the work is done.
    • Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position.
    • Place the wall switch in the “OFF” position.
  4. Mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all sides. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.
  5. Make sure that the ceiling or wall can stand the weight of the lamp before installation.
  6. Make sure the voltage you are using is 120V. The maximum wattage is 18W.
  7. Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp.
  8. When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.
  9. The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products.

IMAGE FOR FINISHED PRODUCT

ZEVNI-A04656-Duran-3-Light 9-Inch-Matte-Black-and-Gold-LED-Flush-Mount-
Light-FIG-1

TOOLS REQUIRED

(NOT INCLUDED)

Before starting assembly and installation please prepare the needed tools as below pictureZEVNI-A04656-Duran-3-Light 9-Inch-Matte-Black-and-Gold-LED-
Flush-Mount-Light-FIG-2

PARTS INCLUDING

  • (C) Single bar (1)
  • (D) Green ground screw (1)
  • (E) Back plate (1)
  • (F) Swivel joint (3)
  • (G) Socket (3)
  • (H) Cap nut (1)

ACCESSORIES ENCLOSED

  • (A) Plastic wire connector (3)
  • (B) Mounting screw (2)

ASSEMBLY & INSTALLATION INSTRUCTIONS

  1. Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.

  2. Turn off power
    Before you start the installation, NEVER attempt any work without shutting off the electricity until the work is done.

    • Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position.
    • Place the wall switch in the “OFF” position.
  3. Make assemblyZEVNI-A04656-Duran-3-Light 9-Inch-Matte-Black-and-Gold-LED-Flush-Mount-Light-FIG-4

  • Step A1 » Unscrew cap nut (H) from single bar (C), then set them aside for later installation.
  • Step A2 » Secure single bar (C) to the outlet box with mounting screws (B).
  • Step A3 » Make wire connections Connect wires as below wires connection shown. PLEASE NOTE THAT GROUND WIRE IS BARE COPPER WIRE, NEVER CONNECT OTHER WIRES TO GROUND WIRES.

Connect ground wires according to the below chart

ZEVNI-A04656-Duran-3-Light 9-Inch-Matte-Black-and-Gold-LED-Flush-Mount-
Light-FIG-5

Connect wires according to the below chart

ZEVNI-A04656-Duran-3-Light 9-Inch-Matte-Black-and-Gold-LED-Flush-Mount-
Light-FIG-6

Note: When parallel wires (SPTI& SPT I) are used. The neutral wire is square shaped or ridged and the other wire will be round in shape or smooth (see illus.)

Twist wires together with plastic wire connectors until tightly joined, and wrap each connector with approved electrical tape. Be sure that no wire strands are exposed and then carefully tuck all wires into the outlet box.

  • Step A4 » Place back plate (E) on the wall and secure back plate (E) in place by tightening cap nut (H) onto the preassembled threaded nipple on single bar (C).

NOTE: The back plate (E) should be snug against the wall with cap nut (H). If not, adjust the threaded length of the preassembled threaded nipple on single bar (C):

  • Unscrew the preassembled hex nut.
  • Screw the preassembled threaded nipple in or out of single bar (C).
  • When the secure length is achieved, tighten the preassembled hex nut and back to step A4.

Step A5 » The direction of light is adjustable:

  • Rotate swivel joints (F) within 350 degrees.
  • Move sockets (G) up and down within 90 degrees.

Check everything is installed properly, then you could turn on the light. Enjoy!

ORDERING PARTS

Keep this sheet for future reference in case you need to order replacement parts. All parts for this fixture can be ordered from the place of purchase. Be sure to use exact wording from illustration when ordering parts.

CLEANING

To clean, wipe the fixture with a soft cloth. Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

ZEVNI User Manuals

Related Manuals