FOREVER MOBILE Cutting Plotter Instruction Manual
- June 9, 2024
- FOREVER MOBILE
Table of Contents
CUTTING
PLOTTER
Instruction Manual
Cutting Plotter
Index: GSM167335
Set contains: Cutting plotter, power supply, manual
Producer/Producent: TelForceOne S.A.
Krakowska 119, 50-428 Wrocław, Poland
Designed by Forever in EU, Produced in PRC
Cautions regarding use
To ensure proper use of our cutting machine, follow the instructions given
below.
A: Safe use
Warning| Incorrect use may lead to injury to personnel. Incorrect operation
can lead to damage to the machine.
---|---
B: Description of signs and symbols
| The symbol indicates that users should pay close attention to this. The
triangle pattern indicates a condition to which you should pay attention. The
left figure shows “watch out for electric
shock”
---|---
| The symbol indicates a prohibited action. The left figure shows “Do not
disassemble”
| Do not use
a power supply that does not match the rated voltage. Using an unlawful
adapter may result in fire or electric shock.
| 1. It is
forbidden to use a power supply that does not meet the rated voltage. Using a
power supply that does not meet the requirements may result in fire or
electric shock.
2. If the machine emits smoke, emits odor, noise or other abnormal
conditions, please do not use it. Under such conditions, it may cause fire or
electric shock.
3.It is forbidden to infiltrate liquid into the machine, and it may fall into
metal objects, etc. These objects may cause shortcircuit fire. 4.It is
forbidden to touch the tip of the knife
with your fingers. The sharper tip may cause finger injury.
5.It is forbidden to destroy or replace the original power cord at will, and
it is forbidden to excessively bend, pull, bind and press under the weight of
the power cable. The power cord maybe damaged, resulting in electric shock or
fire.
6.If the cutting machine is not used fora longtime, please unplug the power
cord from the socket. Doing so may cause a fire.
7.When not in operation, keep your hands on the capstan and may cause injury.
Accessories and machine parameters
A: Kit contents
- One cutting machine
- One knife holder set (including mounted blade inside)
- One power supply
- One power cable
- One machine shortened manual
Others included:
1 sticking pad;
1 cutting pad;
2 squeegees for sticking;
20 cleaning cloths; several test sheets.
B: Machine parameters
- The maximum width of the film sheet: 290mm
- Maximum depth of film sheet: 500mm
- Cutting precision: ± 0.1mm
- Repeated cutting precision: ± 0.1mm
- Cutting speed (4 steps) 300-500mm / S
- Cutting force (5 degrees) 30-90 (Appropriate pressure 150-450g)
- Data transmission mode: built in application; WIFI transmission
- Input voltage: 100-240 V ~ 50-60 Hz 0,5 A
- Output voltage power supply: 24V 、 2,7A (64,8W)
- Working temperature: ﹣5 ° ～ ﹢ 45 °
- Machine weight: 9kg
- Machine dimensions: 600 170 180mm
Machine product schematic
Machine’s schematic diagram and description functions of each part
A: Front of machine
-
LCD display (built in application, setting function)
-
Card slot (card slot in right, material plugged into position)
-
Platen roller (pressing film cutting material front and rear movement)
-
Knife holder (mounting blade, used for cutting materials)
-
Trolley (the left and right cutting of the machine and the loading of the upper and lower blades)
B: Back of machine -
Lever of pressure rollers (used to release the ability to insert or eject a sheet of film) -
Roller pressure springs (they are used to adjust the film sheet stability pressure)
-
Location of “Machine Serial Number” and “Bluetooth Name”
C: Side of machine
-
On-off button (short press to turn on, blue light will be on; about 3sec press to turn off)
-
Power connector (interface to connect to the machine’s power adapter)
D: Machine power supply
-
Power adapter (Power input AC 110-220V Power frequency voltage output 24V= 2,7A)
-
Power cord for the power adapter
Basic operation of the machine
A: Knife holder assembly and adjustment
Before the first use, the correct fixing of the handle consists in its free
fall onto the mounting in the head after unscrewing the fixing screw.
To keep the handle stable, tighten the screw firmly with your fingers.
The knife holder has a total of 10 settings (in the order of 123456789AB).
The larger the number on the handle, the longer the protruding tip of the
knife, which allows for a deeper cut in the material.
The default blade position is factory set for standard transparency film,
other setting items should be changed to correct the blade position according
to different materials.
Let’s take standard film cutting as an example, if the sheet is completely
cut, then we have to reduce the position of the blade on the holder to a
smaller number. Conversely, if the material has not been cut, we must set a
higher number. A properly cut sheet has only the last printed layer scratched,
the other 3 are completely cut.
B: Material placement 
Lower the roller levers to place the sheet in the machine
correctly. Then place the sheet in the machine so that it is aligned to the
right edge and in contact with the sheet slot. At the depth of the device,
the sheet should be exactly behind the line placed on the machine. Sometimes
it may happen that when cutting the film for a large telephone model, the
sheet will slip out from under the pressing rollers, the solution is to place
it deeper in the machine.
Software operation
A: The LOGO interface will be displayed when the machine is turned on.
Add A. During
the first start-up, enter the serial number of the machine, which is located
on the back of the device and begins with “FV………”
B. WIFI connection and entering the serial number Add B. During the first run,
we have the option of choosing the language of the device software. To start
using the machine, you need to connect to the WIFI network and enter the
serial number of the machine, which is located on the back of the machine and
begins with “FV……..”. Then click login. After completing these steps, the
device will start the first update and download the latest data.
C: Software use
C1. Settings In the first setting point, we can change the speed and
cutting force, plus additional settings, e.g. turning off the lamp in the
machine. An additional option is the possibility of a test cut to check the
correct setting of the cutting depth. Important: the cutting speed parameter
should be set as low as possible because the lower the speed, the more
accurate the cut.
The second point is connecting to a WIFI network where we can change the
access point.
The third setting point is the place where, in order to be able to cut the
foil, we must enter the code from the foil package, which is on the back of
the package. 
The
fourth point is to change the language setting of the software.
The fifth point is a place where we can check the statistics of cut foils and
what models we cut foils for.
C2. How to cut
First, we need to put a sheet of foil in the machine (see point 4B of the
instructions).
Important: the sheet should be placed directly in front of the cutout as long-
term storage in the device may cause dents in the film.
Next, we choose the device for which we want to cut the film smartphone,
watch, camera or other.
If we have chosen a smartphone, we can see different brands of devices, for
example (Huawei). Then there is a list of models of a given manufacturer, we
select, for example, (Enjoy 50z) and various types of foil cuts appear. At
this point, we can choose what type of transparent foil cut we need:
Front – i.e. cutting the foil for the entire screen (not recommended if the
customer uses a phone cover with cover – a cut-out especially for customers
using covers After selecting the appropriate cut, click send.
Important: in the category of smartphones “General Category” and watches
“Watch General Category” there are special universal cut-outs with cut-out
dimensions. An additional cutting option is “Custom cutting” available in the
main menu, it allows you to enter your own dimensions and rounding of angles
to match individual needs. However, you must remember about the limitations
resulting from the size of the foil sheet 12x18cm, where the part on which the
rollers move must remain, otherwise the sheet will fall out from under the
rollers. 
Forever
product, a film cutting machine is subject to the manufacturer’s warranty only
if it is used with the use of original films (recommended by the manufacturer)
and sold by TelForceOne S.A.
ATTENTION
The manufacturer is not responsible for the consequences of situations caused
by improper use of the device or non-compliance with the recommendations.
Double protection class
The product is marked with the second protection class symbol. In devices of
this protection class, safety in terms of electric shock is ensured by the use
of appropriate
insulation – double or reinforced – the destruction of which is very unlikely.
For internal use only.
Proper disposal of used equipment
The device is marked in accordance with the European Directive 2012/19/EC
on waste electrical and electronic equipment (Waste Electrical and Electronic
Equipment – WEEE).
Products marked with this symbol should not be recycled or disposed of with
other household waste at the end of their useful life.
The user is obliged to dispose of waste electrical and electronic equipment by
delivering it to a designated point where such hazardous waste is subject to
the recycling process.
The collection of this type of waste in separate places and the proper process
of its recovery contribute to the protection of natural resources. Proper
recycling of waste electrical and electronic equipment has a beneficial effect
on human health and the environment.
For information on where and how to dispose of waste electrical and electronic
equipment in an environmentally safe manner, the user should contact the
appropriate local authority, the waste collection point or the point of sale
where the equipment was purchased.
Declaration of Conformity with European Union Directives
**** TelForceOne S.A. hereby declares that this product complies with the
essential requirements and other provisions of the Directives “New Approach”
of the European Union.