MARLEY EM-JC000 One Drop Wireless Charger User Guide
- June 4, 2024
- MARLEY
Table of Contents
EM-JC000 One Drop Wireless Charger
User Guide ONE DROP
QUICK START GUIDE
One Drop/Qi Wireless Charging Base
DIAGRAM
SET UP
CHARGING
INPUT: 5V/3A, 9V/2A (QC 2.0, QC 3.0)
OUTPUT: 5W | 7.5W | 10W (MAX.)
CHARGING DISTANCE: SUPPORTS CASES UP TO 3MM
| STATUS | LED INDICATION |
|---|---|
| Charging |
Charging Complete
Foreign Object Detected| | Blinking
Off
Blinking
-
SET UP
• Unwrap the included charging cable.
• Connect the USB-C end of the cable to the charging port located on the back of One Drop.
• Connect the USB-A end of the cable to the desired USB-powered port.
• Place One Drop on a flat and stable surface to ensure proper charging. -
CHARGING
• To charge your Qi-enabled wireless device, align the device centered on One Drop.
• A white LED indicator light will slowly blink when your device is properly charging.
• Once your device is fully charged, the white LED indicator light will turn off.
• A red LED indicator light will blink if One Drop detects a foreign object or reaches excessive temperature.
• Quickly remove the object or unplug One Drop to reduce the temperature before continuing usage. -
STORAGE
• When in storage or during travel, it is recommended to remove the charging cable from One Drop.
• Carefully and neatly wind the charging cable.
• Wrap the included cable management strap around the charging cable.
• Insert the tab of the cable management strap into the loop.
• Gently pull the tab ridges through the loop to secure. -
REQUIREMENTS
• Suitable only for Qi-compatible devices.
• Not recommended for devices with over 3mm thick casing.
• Please Note: To achieve Power Delivery fast charging, the device and power source must also support Power Delivery.
Full instruction and warranty details can be found at https://www.thehouseofmarley.com/customer-support/instruction-books
COMPLIANCE INFO
ONE DROP
READ ALL INSTRUCTIONS BEFORE USE AND SAVE THESE INSTRUCTIONS FOR FUTURE
REFERENCE.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with FCC radiation exposure limits set forth for an
uncontrolled environment.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
WARNING:
For Australia and New Zealand for charging this equipment, only use an
Australian-approved detachable power supply unit with output ratings of 5V DC,
500 mA.
FCC & IC RADIATION EXPOSURE STATEMENT
This equipment complies with FCC and Canada radiation exposure limits set
forth for an uncontrolled environment. This equipment should be installed and
operated with a minimum distance of 20cm between the radiator and your body.
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
CAUTION!
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
ISEDC STATEMENT: This device complies with Innovation, Science, and
Economic Development Canada license-exempt RSS standard(s). Operation is
subject to the following two conditions: (1) this device may not cause
interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device. This Class B
digital apparatus complies with Canadian ICES-003.
ISEDC RF EXPOSURE STATEMENT:
The device is compliant with RF exposure guidelines, users can obtain Canadian
information on RF exposure and compliance.
End users must follow the specific operating instructions for satisfying RF
exposure compliance.
The portable device is designed to meet the requirements for exposure to radio
waves established by the Federal Communications Commission (USA).
These requirements set a SAR limit of 1.6 W/kg averaged over one gram of
tissue. The highest SAR value reported under this standard during product
certification for use when properly worn on the body.
WEEE EXPLANATION
This marking indicates that this product should not be disposed of with other
household wastes throughout the EU. To prevent possible harm to the
environment or human health from uncontrolled waste disposal, recycle it
responsibly to promote the sustainable reuse of material resources.
Hereby, FKA Brands Ltd, declares that this radio equipment is in compliance
with the essential requirements and other relevant provisions of Directive
2014/53/EU. A copy of the Declaration of Conformity can be obtained from
www.thehouseofmarley.co.uk/declaration-of-
conformity
To prevent possible hearing damage, do not listen at high volume levels for long periods. Full instructions and warranty details can be found at http://www.thehouseofmarley.com/instructionbooks.
Distributed by
House of Marley, LLC,
3000 N. Pontiac Trail, Commerce Township, MI 48390.
Made In China
QS-EMJC000
©Fifty-Six Hope Road Music Ltd., 2011-2022.
Right of Publicity and Persona Rights.
Fifty-Six Hope Road Music Ltd. EM-JC000
Marley, the Marley logo, Bob Marley and the Bob Marley logo are
registered trademarks of Fifty-Six Hope Road Music Limited and any use
of such marks by The House of Marley is under license. The Bluetooth®
word mark and logos are registered trademarks owned by Bluetooth® SIG,
Inc. and any use of such marks by The House of Marley is under license.
References
- Bob Marley – Dedicated to the life & legacy of Tuff Gong.
- House of Marley Bluetooth Speakers, Headphones, Earbuds & Turntables Inspired by Bob Marley — One Love Movie Giveaway
- Declaration of Conformity - The House of Marley UK
- Customer Support | House of Marley
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>