ZEVNI A04675 Berton 13 Inch Wide Black Vanity Light Instruction Manual
- June 9, 2024
- ZEVNI
Table of Contents
ZEVNI A04675 Berton 13 Inch Wide Black Vanity Light
WARNING (To reduce the risk of fire, electric shock, or personal injury):
-
We suggest installation by a licensed electrician.
-
Please read the instruction carefully and save it as you may need it at a later time.
-
Before you start, NEVER attempt any work without shutting off the electricity until the work is done.
» Go to the main fuse, or circuit breaker, box in your home.
Place the main power switch in the “OFF” position.
» Place the wall switch in the “OFF” position. -
Mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all sides. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.
-
Make sure that the ceiling or wall can stand the weight of the lamp before installation.
-
Make sure the voltage you are using is 120V. The maximum wattage is 40W per bulb.
-
Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp.
-
When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.
-
The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products
IMAGE FOR FINISHED PRODUCT
TOOLS REQUIRED
(NOT INCLUDED):
| | | |
---|---|---|---|---
Ladder| Phillips head-flat blade screwdriver| Electrical tape| pilers| Wire
cutter/stripper
PARTS INCLUDING
(C) Green ground screw (1)
(D) Mounting plate (1)
(E) Back plate (1)
(F) Knob nut (2)
(G) Glass shade (2)
(H) Screw (6)
(I) Socket (2)
(J) Lower tube (2)
**ACCESSORIES ENCLOSED:
**
(A) Mounting screw (2)
(B) Plastic wire connector (3)
ASSEMBLY & INSTALLATION INSTRUCTIONS
-
Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.
-
Turn off power Before you start the installation, NEVER attempt any work without shutting off the electricity until the work is done.
» Go to the main fuse, or circuit breaker, box in your home.
Place the main power switch in the “OFF” position.
» Place the wall switch in the “OFF” position -
Make assembly
-
Check everything is installed properly, then you could turn on the light. Enjoy!
Step A1 » Remove knob nuts (F) from back plate (E), then set them aside for
later installation.
Screw lower tubes (J) onto the bottom of sockets (I)
Step A2 » Carefully pass the supply wires from the outlet box through mounting
plate (D).
Secure mounting plate (D) to the outlet box with mounting screws (A).
Step A3 » Make wire connections Connect wires as below wires connection shown. PLEASE NOTE THAT GROUND WIRE IS BARE COPPER WIRE, NEVER CONNECT OTHER WIRES TO GROUND WIRES
Connect ground wires according to the below chart
Connect ground wires according to the below chart Connect wires
according to the below chart
Connect Black or Red Supply Wire to: | Connect White Supply Wire to: |
---|---|
Black | White |
“Parallel cord ( round & smooth ) | “Parallel cord ( square & ridged) |
Clear ,Brown ,Gold or Black
without tracer
| Clear ,Brown, Gold or Black
with tracer
Insulated wire ( other than green) with copper conductor| Insulated wire ( other than green) with silver conductor
Note: When parallel wires ( SPT I & $PT II) •. are used. The neutral wire is square shaped or ridged and the other wire will be round in shape or smooth ( see ilus.)
Twist wires together with plastic wire connectors until tightly joined,
and wrap each connector with approved electrical tape. Be sure that no wire
strands are exposed and then carefully tuck all wires into the outlet box.
Step A4 » Align the holes in back plate (E) with the preassembled
mounting screws, then attach back plate (E) to mounting plate (D) with the
previously removed knob nuts (F). Hand tighten until snug.
NOTE: back plate (E) should be snug against the wall with knob nuts (F).
If not, remove back plate (E), adjust the threaded length of preassembled
mounting screws on mounting plate assembly (D):
- first, unscrew the preassembled hex nuts;
- then, screw the preassembled mounting screws in or out of mounting plate (D);
- when the secure length is achieved, tighten the preassembled hex nuts and back to Step A4.
Step A5 »
- Carefully place glass shades (G) on sockets (I), and secure them with screws (H).
- Install bulbs (Not included) (Please do not exceed the maximum wattage recommended on the socket.)
ORDERING PARTS
Keep this sheet for future reference in case you need to order replacement
parts. All parts for this fixture can be ordered from the place of purchase.
Be sure to use exact wording from illustration when ordering part
CLEANING
To clean, wipe the fixture with a soft cloth. Clean glass with a mild cleaner
(such as mild and nonabrasive soap). Do not use abrasive materials such as
scouring pads or powders, steel wool or abrasive pap.
www.ihomeangel.com
+1 850 296 2377 Working hours : Mon Fri 9:00 a.m. 16:00 p.m. EST
homecustomercare@outlook.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>