BACK BAY AUDIO Runner 60 Wireless Earbuds User Manual
- June 9, 2024
- Back Bay Audio
Table of Contents
BACK BAY AUDIO Runner 60 Wireless Earbuds
1-Year Warranty
Thank you for purchasing the Runner 60 wireless earbuds! You are covered by our 1-Year Warranty
Register for your free warranty at: www.backbaybrand.com/warranty
How to Power On/Off
- To power on, remove the earbuds from the case or hold the “B” buttons on each earbud for 3 seconds
- To power off, place the earbuds in the case or hold the “B” buttons for 5 sec
- If the case is totally out of battery, the earbuds won’t turn off automatically
Pairing for the First Time
- Remove any protective plastic from the bottom of the earbuds
- Place the earbuds in the charging case until you see a white light
- Remove both earbuds from the charging case and they will automatically turn on and connect to each other
- Go to the Bluetooth menu on your device and select “Runner 60”
- If your phone shows a Bluetooth Pairing Request, press “Pair”
If the earbuds don’t connect to eachother, please follow the directions on the next page
Fixing a Connection Issue
- Open your phone’s Bluetooth settings, find Runner 60″ and click “Forget This Device” or “Unpair”
- Place your earbuds in the charging case
- Press and hold both “B” logos for 10 full seconds until you see the white light turn blue.
- Lift your fingers, then double tap each “B” logo and a light will flash to confirm that the reset was successful
- Remove the earbuds from the case. Then find “Runner 60” in your Bluetooth menu, and press both “B” logos until the earbuds connect to each other
If you don’t see it in your Bluetooth menu, turn your phone’s Bluetooth off and on again
Bass Mode
- To turn Bass Mode on, triple-tap the “B” logo on the right earbud.
- To turn Bass Mode off, triple-tap the “B” logo on the right earbud again
Controls
Positioning
Place the earphone in your ear with the hook going over your ear. Rotate the earbud until you find a comfortable position
Choose the Right Ear-Tip
If you are having trouble putting on the tips, go to the site below for help: backbaybrand.com/eartips
How to Charge
- Charging the Earbuds
- Simply place the earbuds in the charging case (Make sure they are not wet)
- When the earbuds are charging, a white light will shine on the earbuds
- When the earbuds are fully charged, the light will turn off
- The case will recharge the earbuds 9 full times
- Charging the Case
- Locate the USB-C cable included in the accesory box, and plug it into the back of the case
- Or place the case on a wireless charging pad
Do not use a charger that exceeds 5V 1A. A higher-powered charger may damage the battery.
Charging Status
The LED lights on the front of the case will blink to show the battery status when you plug in the case or place the earbuds in the case
- Battery 100%-75% 4 Lights
- Battery 75%-50% 3 Lights
- Battery 50%-25% 2 Lights
- Battery 25%-0% 1 Light
Helpful Charging Tips
- If the earbuds don’t turn off when you put them in the case, it means the case is fully out of battery and needs to be recharged.
- You can leave the charging case plugged in as long as you’d like and it won’t over-charge. We have designed the electronics to prevent over-charging.
Specifications
- Bluetooth Version: 5.0
- Profiles Supported: APTX, HFP, HSP, AVRCP
- Microphone Features: CVC Noise Cancellation
- Supports Cellphone Voice Assistants
- Wireless Range: 10m
- Battery Capacity
- Earphones: 60 mAh
- Dock: 1200 mAh
- Earphone Playtime: Up to 8 Hours
- Total Playtime with Charging Case: 80 Hours
- Charging Time: About 2 Hours
- Frequency Range: 20 Hz- 20 kHz
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>