JOCIRUS T6 Wire-Free WiFi Video Doorbell User Manual
- June 9, 2024
- JOCIRUS
Table of Contents
JOCIRUS T6 Wire-Free WiFi Video Doorbell
Warm Support
Dear Friends : Thank you for ordering our doorbell camera! We are keeping
to optimize product and improve our customer service to offer you a better
shopping experience. Please refer to the notes below and follow the
instructions in this manual to ensure that you use the doorbell camera
correctly and have a good experience with this product.
If your have any problems during use, please feel free to contact us. We will
provide a fast solution in 24 hours. Besides, your advice and suggestions will
be much appreciated and welcomed. Thank you again for ordering our product. We
truly appreciate your business. We love our customers and we will always be
here with our professional camera engineers. Wishing you the best Customer
Support Team
How to contact us:
- Open Aiwit app
- Click customer service button
- Enter your question and click send
- Due to the time difference, there may be a delay in responding to customer service messages, and we will reply within 24 hours at the latest.
- Microphone
- Motion Sensor
- Wide-angle Lens
- LED indicator
- Hidden Infrared Lights
- Light Sensor
- Doorbell Button
- Speaker
- Micro USB Port (Battery Charging)
- Battery Compartment
Indicator Light
Indicator light flashing RED
The device is reconnecting to the Wifi network. Please wait.
Indicator light flashing RED and BLUE alternately
Low battery. Please recharge your batteries.
Flashing BLUE
The device is recording.
In the box
Charge batteries
- Remove the battery tab.
- Insert 18650 batteries positive end facing up, as shown on the device.
- Fully charge batteries by connecting your device to a USB charger using a Micro USB cable. It takes about 14 hours for batteries to fully charge.
WARNING : Lots of events If your device is capturing an excessive number of events every day, you might need to recharge your battery sooner. Plus, the battery is also drained each time you use the Live View to look or speak through your doorbell. To prevent excessive events, you can adjust your motion settings to a lower sensitivity.
Set up your Video Doorbell
Before You Start
-
Download and install Aiwit App. Scan the QR code below or search for Aiwit on the Apple App Store or Google Play. Download and install the app.
NOTICE:
To make sure every single feature works properly, please select “YES” for all permissions on your phone during the App installation.
-
Create an Aiwit account with your email address and activate the account by the email you received.
Set up your device in the Aiwit app.
To pair your device, follow the steps below and in-app instructions.
- Open Aiwit App and log in.
- To add your camera, select the + icon.
- Select Video Doorbell.
- Select the corresponding model.
- Press and hold the Doorbell Button until the red light is flashing, then tap Yes.
- Enter your 2.4GHz Wi-Fi network and the Wi-Fi password, then tap Next (5GHz is not supported).
- Use your device camera to scan the QR Code shown on the app, then select Confirm once the Wi-Fi setup has finished.
- If the doorbell connected with your WiFi successfully, a notification will appear on your screen as shown below. if it fails to connect with your WiFi, please repeat steps 5 to After setup, you will be able to check the live footage on your screen, and operate the doorbell with your phone.
NOTICE:
If you experience some issues during the app setup, try the following steps:
Check your WiFi password.
The most common issue during setup is an incorrect WiFi password, passwords
are case-sensitive. Please double check your password.
Reboot the router/moden.
If you have entered the correct password, but are still experiencing issue,
try unplugging the power to your router/modem. wait for 30 seconds, then plug
it back in and turn it on. proceed to setup again in Aiwit app.
Install your Video Doorbell
Before You Start Installing
Select the location where you need to install the camera, take the camera and
the phone to the location, enter into the information interface to check if
the WiFi signal at the location is good. it is recommended to install the
camera in a location with good WiFi signal for smooth camera operation.
Mark drill holes and use a bit to drill holes in your wall. Insert anchors and secure your doorbell with mounting and security screws.
Set up your Wireless Chime (Optional)
Connect the video doorbell to the doorbell chime, and get instant alert in your home when someone rings the doorbell. The chime can be powered by any USB adapter in your home (DC 5V).
NOTICE:
The video doorbell is only compatible with our wireless chime, and not
compatible with traditional doorbell chimes. The wireless chime is optional.
If it is not installed, doorbell notifications will still go directly to the
Aiwit app.
The Basics
Set up your chime with the video doorbell.
- Step 1 Before the setup process, be sure your video doorbell has connected to your phone and plug our chime in a 5V USB adapter.
- Step 2 Press the Connect Button.
- Step 3 Press the Doorbell Button to pair your doorbell to the chime.
- Step 4 Press the Doorbell Button again to check if the chime is connected successfully.
Frequently asked questions
Can not connect to WiFi to complete the set up process.
- Please check if the Wi-Fi network is in good condition, and put the doorbell and your smart phone as close as to your router. Poor network conditions may cause connection failure.
- Please check if the Wi-Fi frequency band is 2.4GHz, this door cannot connect to 5GHz Wi-Fi network.
- Please check if the Wi-Fi password contains special characters such as “!&#$%”, sometimes the APP cannot recognize some special characters, which will cause the connection to fail.
- If it still doesn’t work, please contact customer service.
Why does the battery still show 1% after charging it overnight?
Please remove the insulating sheet at the bottom of the battery before
charging.
Can this camera be set to record all the time?
No, our doorbell cannot be set to record all the time. When motion detection
is triggered or someone ring the doorbell, the camera will automatically
record a
20-second video; when you actively view the real-time video, the doorbell will
record a video of up to three minutes continuously; at other times, the
doorbell is in standby mode.
How to RESET the doorbell?
Press and hold the Doorbell Button for 8 seconds. Then follow the in-app
instructions to finish your Wi-Fi setup.
How to share the device with my family?
Open the Aiwit app. From the home page, tap the Share icon. Tap Share via
Email or Share via QR Code. You can share the device with up to 8 users.
Share via Email:
The new user has to download the Aiwit app and create an account with the same
email address which the device owner will share with. Log in to the account
and you’ll see the shared device.
Share via QR Code:
- Open the Aiwit App on a new user’s smartphone.
- From the home page, tap +.
- Tap QR Code Sharing, then scan the QR code the device owner generated before.
- You will see Share successful, then tap Confirm.
How many users can view the video at the same time?
Up to 3 users may view the video feed, but only 1 user can use the direct
intercom. Both iOS and Android are compatible.
Is 5GHz Wi-Fi supported?
No, only 2.4GHz Wi-Fi is supported.
How long can the battery last after being fully charged?
Generally, the battery can last around 1200 notifications. Different
temperatures can make the battery life vary.
Why does my doorbell sometimes go offline?
Your doorbell may be too far from the wireless router or you may have some
obstructions in between that reduce the WiFi signal strength. You may need to
try repositioning your router or getting a WiFi extender for your wireless
router. It is recommended to keep the RSSI value displayed by the APP between
0dBm and -50dBm, so that the doorbell can maintain a stable connection and
watch and upload videos smoothly.
Why doesn’t my phone get messages when someone walks past my door?
- You need to turn on the notification permissions of the Aiwit App in the phone settings:
- Open Settings. Go to Aiwit app permissions and select Notifications.
- Make sure all switches are on.
- Please open the self-starting permission of the APP, and set the power management to unlimited. Only when you open the app or it run in the background, you will receive alerts and visitor messages.
How to adjust Motion Detection Sensitivity?
From the home page, tap the Motion Detection icon.
Function On & Off
- Motion : Turn on/off motion detection.
- Motion Alerts : Turn on/off the motion alerts of App.
- Ring Alerts : Turn on/off the ring alerts of App.
Motion Detection Sensitivity
- High : Records and notifies you about every motion. Shortest battery life.
- Medium : Records and notifies you about motion less often. Standard battery life.
- Slow : Records and notifies you about motion even less often. Maximum battery life.
Humanoid Detection
- When the level of humanoid detection is low, the doorbell may trigger the alarm when it captures a part of the human body (such as head, hand, etc.).
- when the level is adjusted to high, the doorbell will only trigger the alarm when it captures the entire humanoid.
- You can adjust the level from low to high according to your needs.
How can I talk to people through the doorbell?
Open the app and enter the video preview interface. The microphone button
and sound button are disabled by default. Click to open them, and you can talk
to the visitor.
Note: To get the intercom, you need to give the Aiwit app permission to access your microphone.
What type of Micro SD card should I use?
The device comes with cloud storage, so no SD card is needed.
Why does my battery die extremely quickly?
- When motion detection is triggered frequently, battery power consumption will speed up. Please check whether there are objects within the field of view of the device that interfere with and trigger the PIR sensor, such as outdoor units of air conditioners, direct sunlight, glass window, leaves etc. If yes, please adjust the position of the doorbell, turn down the motion detection alarm sensitivity or turn on the humanoid detection.
- Your device maybe too far away from your wireless router or you may have some obstructions in between that reduce signal strength. Your device keeps on finding and reconnecting with the WiFi, which will drains the battery.
- Due to the characteristics of lithium batteries, the battery capacity will be significantly reduced in cold winters, and will return to normal when the temperature warms up.
What if I want to buy a spare battery?
Please choose 18650 battery with a raised positive electrode, otherwise the
device will not be able to be used and charged.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>