ISUZU TN0040A Car Audio Instruction Manual

TN0040A
Operation Manual TN0040A Car

Model name Car Audio
Model No TN0040A

Specification of the EUT

Bluetooth : Hands Free and Audio
WiFi : For Wireless Carplay/AndroidAuto
GNSS : GPS, Galileo, GLONASS, QZSS
RATED VOLTAGE| 12.0V (10.5～16.0V) – ground
LOAD IMPEDANCE| 4Ω
BACK UP CURRENT| 1mA or less
RATED CURRENT| 1.98Ａ　or less
(Vcc=13.2V, 0.5W output)
AM TUNING RANGE| 522 – 1710 kHz (9kHz step)
FM TUNING RANGE| 87.5 – 108 MHz (100kHz step)
DAB TUNING RANGE| 174.928 – 239.200 MHz
Rating of usage environment| – 30 to +65 °C
(Perfomance assured temperature range)
Size of Equipmet| D 178.15mm×W 253.89mm×H 174.49mm
Weghit of Equipmet| 2050g
Software version| –
Hardware version| –

Button Function Spec

■ AUDIO controls

knob: Jump between preset channels
②| NAVI| Transition to MAP screen
③| TALK| Short Push: Transition to Dial screen
Long Push: Transition to Bluetooth pairing screen
④| HOME| Transition to home screen
⑤| BACK| Transition to previous screen
⑥| VEHICLE| Transition to vehicle information screen.
➆| VOLUME/POWER| Push knob: Audio ON/OFF
Rotate knob to the right: Adjust volume by +1 Rotate knob to the left: Adjust volume by -1

Radio operation procedure

[Operation procedure]

1. (ACC-ON)
   After the ACC-ON, confirm that Isuzu screen is displayed.

2. CAUTION
   The screen is changed to “CAUTION” screen after a few seconds.
   Note: It takes a little longer for the first time of ACC-ON.

3. Continue
   Press the “Continue” button on the face panel after a few seconds to move MENU screen.

4. POWER
   Press the POWER button.
   When the Radio Mode Window on the screen is pressed,”FM1″ screen is displayed.

5. Confirm that the screen is changed as below,
   Please push down the ”<”button or ”>”button.
   This will start to SEEK.※AM/DAB
   ※Same as AM/DAB mode.

Operating manual (Bluetooth/Handsfree)

[Operation procedure]

1.  (ACC-ON)
   ACC-ON After the ACC-ON, confirm that Isuzu screen is displayed.

2. CAUTION
   The screen is changed to “CAUTION” screen after a few seconds.
   Note: It takes a little longer for the first time of ACC-ON.

3. MENU
   Press the “Continue” button on the face panel after a few seconds to move MENU screen.

4. Setting SETTINGS
   Please press the “Setting” button on the face panel to move to Settings screen

5. Settings Bluetooth
   Confirm if ”Settings” screen is displayed, select the ”Bluetooth” button on the display.

6. Add Device
   Please press the ”Add Device” button of the screen

7. Search Device
   Please press the ”Search Device” button of the screen

8. (iPhone, iPod
   Confirm if screen is changed as below, Please set iPhone or iPod in pairing mode. ※Displays when you have more than one pairing equipment

9. iPhone iPod
   Select the iPhone or iPod to connect. ※ Operate the phone after the message on the screen

10. Connection Completed”
    ”Connection Completed” is displayed if completed.

FCC Operating manual Requirement

CAUTION: Radio Frequency Radiation Exposure
This equipment complies with FCC radiation exposure limits set forth for uncontrolled equipment and meets the FCC radio frequency (RF) Exposure Guidelines. This equipment should be installed and operated keeping the radiator at least 20cm or more away from person’s body.
Co-location: This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
FCC WARNING
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>