milwaukee M18 BSX Cordless Recipro Saw Instructions
- June 8, 2024
- Milwaukee
Table of Contents
M18 BSX Cordless Recipro Saw
Instructions Manual
M18 BSX Cordless Recipro Saw
TECHNICAL DATA
Production code………………………………………………………………….
Battery voltage……………………………………………………………………
Stroke rate under no-load …………………………………………………….
Lengths of stroke ………………………………………………………………..
Cutting depth max. in soft wood ……………………………………………
Cutting depth max. in steel …………………………………………………..
Cutting depth max. in aluminium …………………………………………..
Cutting depth max. in Non-ferrous metal ………………………………..
Cutting depth max. in Metal pipe / Profi les ……………………………..
Weight according EPTA-Procedure 01/2014 (2,0 Ah – 12,0 Ah) …
Recommended ambient operating temperature ………………………
Recommended battery types………………………………………………..
Recommended charger ……………………………………………………….| ………………… 4697 97 03……000001-999999
………………………18 V
………………..0-3000 min-1
……………………28,6 mm
…………………….300 mm
………………………20 mm
………………………25 mm
………………………25 mm
…………………….150 mm
……………..3,7 – 4,8 kg
……………..-18…+50 °C
…………….M18B2… M18HB12
………….. M12-18 … ; M1418C6
---|---
Noise/vibration information
Measured values determined according to EN 62841.
Typically, the A-weighted noise levels of the tool are:
Sound pressure level (Uncertainty K=3dB(A)) …………………………..82,9 dB (A)
Sound power level (Uncertainty K=3dB(A)) …………………………….93,9 dB (A)
Wear ear protectors!
Total vibration values (vector sum in the three axes) determined according to
EN 62841.
Cutting board 1
Vibration emission value ah,B ………………………………………………..18,0 m/s²
Uncertainty K= ………………………………………………………………………1,5 m/s²
Cutting wooden beam 2
Vibration emission value ah,WB…………………………………….15,2 m/s²
Uncertainty K= ………………………………………………………………1,5 m/s²
1 with saw blade bimetal, dimension 230 x 1,6 mm and tooth pitch 5 mm The AxTM
2 with saw blade bimetal, dimension 150 x 1,25 mm and tooth pitch 5 mm
WARNING
The vibration emission level given in this information sheet has been measured
in accordance with a standardised test given in EN 62841 and may be used to
compare one tool with another. It may be used for a preliminary assessment of
exposure.
The declared vibration emission level represents the main applications of the
tool. However if the tool is used for diff erent applications, with diff erent
accessories or poorly maintained, the vibration emission may diff er. This may
signifi cantly increase the exposure level over the total working period.
An estimation of the level of exposure to vibration should also take into
account the times when the tool is switched off or when it is running but not
actually doing the job. This may signifi cantly reduce the exposure level over
the total working period.
Identify additional safety measures to protect the operator from the eff ects
of vibration such as: maintain the tool and the accessories, keep the hands
warm, organisation of work patterns.
WARNING Read all safety warnings, instructions, illustrations and specifi cations provided with this power tool. Failure to follow all instructions listed below may result in electric shock, fi re and/or serious injury. Save all warnings and instructions for future reference.
SABRE SAW SAFETY WARNINGS
Hold the power tool by insulated gripping surfaces, when performing an
operation where the cutting accessory may contact hidden wiring.
Cutting accessory contacting a “live” wire may make exposed metal parts
of the power tool “live” and could give the operator an electric shock.
Use clamps or another practical way to secure and support the workpiece to a
stable platform. Holding the work by your hand or against the body leaves it
unstable and may lead to loss of control.
ADDITIONAL SAFETY AND WORKING INSTRUCTIONS
Use protective equipment. Always wear safety glasses when working with the
machine. The use of protective clothing is recommended, such as dust mask,
protective gloves, sturdy non-slip footwear, helmet and ear defenders.
The dust produced when using this tool may be harmful to health. Do not inhale
the dust. Wear a suitable dust protection mask.
Do not machine any materials that present a danger to health (e.g. asbestos).
Switch the device off immediately if the insertion tool stalls!
Do not switch the device on again while the insertion tool is stalled, as
doing so could trigger a sudden recoil with a high reactive force. Determine
why the insertion tool stalled and rectify this, paying heed to the safety
instructions.
The possible causes may be:
- it is tilted in the workpiece to be machined
- it has pierced through the material to be machined
- the power tool is overloaded
Do not reach into the machine while it is running.
The insertion tool may become hot during use.
WARNING! Danger of burns
- when changing tools
- when setting the device down
Chips and splinters must not be removed while the machine is running.
When working in walls ceiling, or fl oor, take care to avoid electric cables and gas or waterpipes.
Clamp your workpiece with a clamping device. Unclamped workpieces can cause severe injury and damage.
Do not use cracked or distorted saw blades.
Plunge cuts without pre-drilling a hole are possible with soft materials (wood, light building materials for walls). Harder materials (metals) must fi rst be drilled with a hole corresponding to the size of the saw blade.
Remove the battery pack before starting any work on the machine.
Do not dispose of used battery packs in the household refuse or by burning
them. Milwaukee Distributors offer to retrieve old batteries to protect our
environment.
Do not store the battery pack together with metal objects (short circuit
risk).
No metal parts must be allowed to enter the battery section of the charger
(short circuit risk).
Use only System M18 chargers for charging System M18 battery packs. Do not use
battery packs from other systems.
Never break open battery packs and chargers and store only in dry rooms. Keep
dry at all times.
Battery acid may leak from damaged batteries under extreme load or extreme
temperatures. In case of contact with battery acid wash it off immediately with
soap and water. In case of eye contact rinse thoroughly for at least 10
minutes and immediately seek medical attention.
Warning! To reduce the risk of fi re, personal injury, and product damage
due to a short circuit, never immerse your tool, battery pack or charger in fl
uid or allow a fluid to flow inside them. Corrosive or conductive fl uids, such
as seawater, certain industrial chemicals, and bleach or bleach containing
products, etc., can cause a short circuit.
EC DECLARATION OF CONFORMITY
We declare as the manufacturer under our sole responsibility that the product
described under “Technical Data” fulfi lls all the relevant regulations and the
directives 2011/65/EU (RoHS), 2014/30/EU, 2006/42/EC, and the following
harmonized standards have been used:
EN 62841-1:2015
EN 62841-2-11:2016+A1:2020
EN 55014-1:2017+A11:2020
EN 55014-2:2015
EN IEC 63000:2018
Winnenden, 2021-08-16
GB-DECLARATION OF CONFORMITY
We declare as the manufacturer under our sole
responsibility that the product described under “Technical
Data” fulfi lls all the relevant provisions of the following
Regulations S.I. 2008/1597 (as amended), S.I. 2016/1091
(as amended), S.I. 2012/3032 (as amended) and that the
following designated standards have been used:
BS EN 62841-1:2015
BS EN 62841-2-11:2016+A1:2020
BS EN 55014-1:2017+A11:2020
BS EN 55014-2:2015
BS EN IEC 63000:2018
Winnenden, 2021-08-16
Alexander Krug
Managing Director
Authorized to compile the technical fi le.
Techtronic Industries GmbH
Max-Eyth-Straße 10
71364 Winnenden
Germany
SPECIFIED CONDITIONS OF USE
This sabre cut is intended to cut wood, plastic, and metal. It can cut
straight lines, curves, and internal cut-outs. It cuts pipes and can cut fl ush
to a surface.
Do not use this product in any other way as stated for normal use.
BATTERIES
Battery packs which have not been used for some time should be recharged
before use.
Temperatures in excess of 50°C (122°F) reduce the performance of the battery
pack. Avoid extended exposure to heat or sunshine (risk of overheating).
The contacts of chargers and battery packs must be kept clean.
For an optimum life-time, the battery packs have to be fully charged, after
used.
To obtain the longest possible battery life remove the battery pack from the
charger once it is fully charged.
For battery pack storage longer than 30 days:
Store the battery pack where the temperature is below 27°C and away from
moisture
Store the battery packs in a 30% – 50% charged condition
Every six months of storage, charge the pack as normal.
BATTERY PACK PROTECTION LI-ION BATTERY
The battery pack has overload protection that protects it from being
overloaded and helps to ensure long life.
Under extreme stress the battery electronics switch off the machine
automatically. To restart, switch the machine off and then on again. If the
machine does not start up again, the battery pack may have discharged
completely. In this case it must be recharged in the battery charger.
TRANSPORTING LITHIUM BATTERIES
Lithium-ion batteries are subject to the Dangerous Goods Legislation
requirements.
Transportation of those batteries has to be done in accordance with local,
national and international provisions and regulations.
-
The user can transport the batteries by road without further requirements.
-
Commercial transport of Lithium-Ion batteries by third parties is subject to Dangerous Goods regulations.
Transport preparation and transport are exclusively to be carried out by appropriately trained persons and the process has to be accompanied by corresponding experts.
When transporting batteries: -
Ensure that battery contact terminals are protected and insulated to prevent short circuit.
-
Ensure that battery pack is secured against movement within packaging.
-
Do not transport batteries that are cracked or leak.
Check with forwarding company for further advice
MAINTENANCE
The ventilation slots of the machine must be kept clear at all times.
Use only Milwaukee accessories and spare parts. Should components need to be
replaced which have not been described, please contact one of our Milwaukee
service agents (see our list of guarantee/service addresses).
If needed, an exploded view of the tool can be ordered.
Please state the machine type printed as well as the six-digit No. on the
label and order the drawing at your local service agents or directly at:
Techtronic Industries GmbH,
Max-Eyth-Straße 10, 71364 Winnenden, Germany.
SYMBOLS
| CAUTION! WARNING! DANGER!
---|---
| Remove the battery pack before starting any work on the machine.
| Please read the instructions carefully before starting the machine.
| Always wear goggles when using the machine.
| Accessory – Not included in standard equipment, available as an accessory.
| Do not dispose electric tools, batteries/rechargeable batteries together
with household waste material.
Electric tools and batteries that have reached the end of their life must be
collected separately and returned to an environmentally compatible recycling
facility.
Check with your local authority or retailer for recycling advice and
collection point.
n0| Stroke rate under no-load
V| Volts
| Direct current
| European Conformity Mark
| British Confomity Mark
| Ukraine Conformity Mark
| EurAsian Conformity Mark
Copyright 2021
Techtronic Industries GmbH
Max-Eyth-Str. 10
71364 Winnenden
Germany
+49 (0) 7195-12-0
www.milwaukeetool.eu
Techtronic Industries (UK) Ltd
Fieldhouse Lane
Marlow Bucks SL7 1HZ
UK
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>