legrand WNAL50 adorne SofTap Smart Tru Universal Dimmer Instruction Manual
- June 8, 2024
- Legrand
Table of Contents
WNAL50 adorne SofTap Smart Tru Universal Dimmer
Instruction Manual WNAL50
adorne™ Smart Dimmer w/ Netatmo
No: 341333 – 08/21
adorne ® SofTap TM
Smart Tru-Universal Dimmer with Netatmo, 2-Module
Wall plate sold separately
WNAL50 adorne SofTap Smart Tru Universal Dimmer
Catalog Number(s) : WNAL50
Country of Origin: Made in China
REGULATORY INFORMATION
FCC NOTICE: This device complies with Part 15 of the FCC rules. Operation
is subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesirable operation. This
equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna
- Increase the separation between the equipment and receiver
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
- Consult the dealer or an experienced radio/TV technician for help
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance of 90 mm between the transmitter’s radiating structure(s)
and the body of the user or nearby persons.
NOTE: Any changes or modifications to this device that are not expressly
approved by the manufacturer will void the warranty and the user’s authority
to operate the equipment.
Contains FCC ID: 2AU5D982057
IC NOTICE : This device complies with Industry Canada license-exempt RSS
standards. Operation is subject to the following two conditions:
(1) this device may not cause interference; and (2) this device must accept
any interference, including interference that may cause undesired operation of
the device.
RF EXPOSURE STATEMENT : This equipment meets the SAR evaluation limits
given in RSS-102 Issue 5 requirements at the minimum separation distance of 90
mm to the human body.
Note: Any changes or modifications to this device that are not expressly
approved by the manufacturer, will void the warranty and the user’s authority
to operate the equipment.
IC: 25764-982057
HVIN: 982057
CAUTIONS
To reduce the risk of overheating and possible damage to other equipment, do
not install dimmer to control a receptacle or a motor-operated appliance.
Do NOT use dimmer with incandescent lamps whose power requirements exceed
maximum wattage of the dimmer.
Max. load rating:
- Incandescent: 700W Forward / 450W Reverse
- MLV: 500VA
- ELV: 700W Forward / 450W Reverse
- EFL: 4.5A Forward / 2.1A Reverse
- CFL and LED: 4.5A Forward / 2.1A Reverse
Min. load rating:
- Incandescent: 20W
- MLV: 20VA
- ELV: 20W
- EFL: 50mA
- CFL and LED: 50mA
Do NOT connect dimmer to power source other than 120VAC, 60 Hz.
NOTE: No derating required for multi-gang installation.
Remove spacers from the frame. Since this dimmer fills the
frame completely, you will not need the spacers. From the back of the frame,
pinch the tabs on the spacer to release.
Use only with Legrand adorne TM system.
For more information and helpful how-to videos, visit
www.adornemyhome.com/install.
INSTALLATION INSTRUCTIONS
Please read these instructions completely before you begin.
This adorne TM device is designed for installation in standard electrical
boxes. However, some of the installation methods vary slightly from
traditional methods. If you do not understand these instructions or are unsure
of your abilities, seek the assistance of a qualified electrician.
WARNING
To prevent severe shock or electrocution, always disconnect power at the
service panel before beginning work.
When replacing existing dimmers, label wires before disconnecting.
Disconnect old dimmer.
Single Pole
Identify the Common or Hot wire attached to the black screw.
Identify the neutral wire attached to the silvercolored screw. The remaining
wire will be attached to a coppercolored screw. 
3-Way
For 3-way application, secure the spare wire with a wire nut and pair your
smart dimmer with a wireless dimmer PN WNAL63.
If necessary, cut wires and strip insulation using stripping guide on back of
dimmer.
**WARNING
Failure to connect the ground wire will result in an unsafe installation that
could lead to personal injury.
Connect frame ground wire to bare ground wire in box. Fold ground wires into
back of box. Mount frame to wall box with screws provided. Tighten screws just
enough to
hold frame in place. Do NOT over-tighten. 
TIPS**
- Pre-fold wires into wall box to make it easier to fit them in the box when dimmer is connected.
- Use caution to avoid marring wall surface with the metal frame.
Connect new smart gateway as shown.
Make sure the terminal holes are clear. Insert wires into terminals and torque
terminal screws to 14-16 inch-pounds. Do NOT over-tighten.
**WARNING: Do not pair different size wires in the same terminal. If
you have different size wires, use a wire nut to add a 6 inch pigtail of the
same gauge wire to the smaller gauge wire.
Single
Pole**
- Connect the wire identified as Common/Hot in Step 1 to HOT.
- Connect the wire identified as Neutral in Step 1 to WHITE.
- Connect other wire to load.
SINGLE POLE
NOTE: In a 3-Way or 4-way
Installation, use only one hard wired dimmer (WNAL50) and additional battery
powered dimmer(s) (WNAL63). 3-Way (Replacing Existing Installation)
- Connect the wire identified as Common/Hot in Step 1 to HOT.
- Connect the wire identified as Neutral in Step 1 to WHITE.
- Connect one of the other wires to load.
- Attach wire nut to remaining traveler wire.
Carefully fold wires into box. Snap the dimmer into frame.
TIP – Since the frame completes the enclosure, it’s safe
to power up the dimmer and test. Allow one minute for the electronics to
charge after installation.
NOTE: If you need to remove the device after snapping into frame, first
remove frame from wall box to access the four locking tabs on the back of the
device. Insert a flat screwdriver to depress tabs as you apply pressure to
push the dimmer out.
Test the Smart Dimmer
NOTE: See getting to know your dimmer section for feature details. Turn
the power back on at the circuit breaker, press switch to turn light on/off.
This device is designed to work with the adorneTM Smart Gateway with Netatmo.
Follow the instructions from your app to finish setting up your dimmer.
TROUBLESHOOTING TIP : If the device is not powering check wiring to
determine if you have reversed the “HOT” and “LOAD” wiring.
Set up your System
a. Download and launch the Legrand Home + Control app. The app is available on
the App Store or on Google Play.
b. Connect your smart device to your home network by following the step by
step instructions in the app.
c. Use the app to control your smart device.
Getting to Know Your Dimmer
| Item | Name | Description |
|---|---|---|
| 1 | Paddle Switch | Press the top of the paddle to turn light on and the bottom |
of paddle to turn light off
2| LED Locator Light| Used to initiate device setup. Marked with a “*” icon
3| Dimmer Paddle/ LED Light Level| Controls and displays the dimming
percentage
Press (+/-) to adjust light in 2% increments.
Hold (+/-) to adjust light in 20% increments.
4| Air Gap Switch| Completely turns off the dimmer. Use when changing light
bulbs
5| EZ Button| Used to enter setup mode
LED Indicator Light Explanation
| State of LED | Behavior of Device |
|---|---|
| Solid White | Lit when load is off |
| Solid Red | Factory reset, not in network |
| Blinking Green | Device is attempting to connect to the network mode |
| Solid Green | Device in network, temporarily open |
Reset To Factory Default
Deleting a device from the app will reset it to factory defaults.
To manually reset the device to factory defaults press and hold the EZ button
for 10 seconds until you see the LED blink red then release.
The LED will change to solid red when the reset is complete.
Due to ongoing product improvements, Legrand reserves the right to change
specifications without notice. For the most recent instruction sheets or more
information on this product, please see this link or scan the QR code:
https://www.legrand.us/p/wnal50wSnap wall plate to frame.
There are three click-stops to adjust the fit of the wall plate to the dimmer
and the wall.
NOTE: To remove wall plate, insert a small, flat screwdriver in notches on wall plate and twist gently to pry from frame. Never apply cleaner directly to the device or wall plate. Apply to a soft cloth and use cloth to remove any smudges from the product.
Technical Assistance:
877-295-3472
www.adornemyhome.com/install
LIMITED TWO-YEAR WARRANTY
Limited two-year warranty information for adorne products is available at www.legrand.us/adorne/warranty. Limited warranty information for adorne TM products may also be obtained free of charge by sending a written request, along with your proof of purchase (including purchase date), to:
Legrand
Attn: adorne Customer Service/Warranty Department
50 Boyd Avenue
Syracuse, NY 13209
No: 341333 – 08/21
© Copyright 2021 Legrand All Rights Reserved.
60 Woodlawn Street
West Hartford, CT 06110
1.877.BY.LEGRAND
(295.3472) www.legrand.us
CANADA
905.738.9195 www.legrand.ca
References
- Search Results Page
- Legrand US | Delivering and Managing Power, Light, and Data
- The adorne® Collection | Legrand
- adorne® Warranty ⎸Legrand
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>