evolur 851 Fully Assembled Changing Tray Instruction Manual

evolur 851 Fully Assembled Changing Tray Instruction Manual

Assembly

Adult assembly required.
Small parts may present choking hazard prior to assembly.

Enclosed please find simple step-by-step instructions to help you quick assemble your product. Before you begin, we recommend that you follow the steps below:

1. Please read the instructions thoroughly
2. Identify all parts and hardware
3. You may need to provide the following tools:
   • Philips Head screw driver
   • Flat head screw driver
   • Hammer

Do Not Use Power Drills Or Drivers

To protect your parts during assembly please please place them on a soft surface. To clean surface, use only water on a damp cloth.
Do not use window cleaner or cleaning abrasive as it will scratch the surface and could damage the protective coating.

Furniture Care Instructions

Room Climate Control
Wood, when first cut contains more than 50 percent water. When it is prepared for furniture construction it is placed in a Kiln and the moisture content is brought down toil to 10 percent. Wood Is porous and responds to Its environment. If the room has high humidity It will absorb it and expand and if the humidity is low it will lose moisture and shrink.

It Is Important that the humidity levels in the room be controlled from extremes of too much humidity or too little. Furniture should not be placed close to air-conditioning outlets, fire places, radiators, space heaters, humidifiers or dehumidifiers. Exposure to extreme variations of temperature and humidity can damage any fine wood product.

The Ideal Environment for Fine Furniture
Fine wood furniture will have fewer problems when its environment is controlled at a temperature between 65 and 75 degrees and a relative humidity between 35 and 40 percent. Wood placed in an environment out side of those limits can and will shrink or expand and may develop some small cracks which are not material or structural defects.

Sticking Doors and Drawers
With the minor changes in temperature and humidity doors and drawers may swell and be difficult to open or close. Tolerances have been built Into the units but extreme conditions may still cause sticking. This will adjust back to normal over time but until it does consider using a dehumidifier or rub candle wax or paraffin on the sides that stick.

Avoid Direct Sunlight
Keep the furniture out of direct sunlight. Ultraviolet rays will fade colors and in some cases darken them. It can also cause crazing or hair line cracks in the finish. White finishes will yellow naturally over time and exposure to direct sunlight will hasten this natural process along with some woods darkening naturally over time; this is not considered to be a quality defect.

Proper Storage
If you need to put your furniture In storage for any period of time do not store them in a damp basement or hot dry attic. Allow air movement around the furniture and do not stack anything on it.

In General

• Protect furniture surface from hot or extremely cold items.
• Use coasters under hot or cold beverages
• Do not use synthetic fabric under accessories or lamps
• Protect tops from pens, makers and crayons
• Oils from potpourri and other scented items can damage the furniture finish.
• Do not drag Items across the surface of the furniture.
• Allow the surface to breath by rotating your accessories and lamps.
• Do not over polish the furniture, do it only two or three times a year. Over polishing can distort the natural finish of the product.
• Do not wax the furniture as wax build up can destroy the natural finish of the product
• When moving furniture always lift the unit. Do not push or drag it to avoid damage to legs
• Keep the furniture level so doors and drawers open and close freely.
• Clean with a damp, not wet, cloth. Use only a mild soap. Do not use abrasive cleaners.

HARDWARE AND TOOL DIAGRAM

• A. x4 (5/8 ”)

• B. x 2

• C. x 2 ( 3/4”)

• (NOT PROVIDED)

WARNING

• READ ALL INSTRUCTIONS BEFORE USE OF THE CHANGING TRAY OR CHANGING PAD
• KEEP ALL INSTRUCTIONS FOR FUTURE USE
• WARNING: FALL HAZARD – TO PREVENT DEATH OR SERIOUS INJURY, ALWAYS KEEP CHILD WITHIN ARM’S REACH
• DO NOT USE THIS CHANING TRAY IF THERE ARE ANY LOOSE JOINTS, MISSING OR BROKEN PARTS AND / OR SHARP EDGES . CONTACT DREAM ON ME INC., 1532 S. WASHINGTON AVE, PISCATAWAY, NJ 08854 FOR REPLACEMENT PARTS AND INSTRUCTIONAL LITERATURE. DO NOT SUBSTITUTE PARTS OF ANY KIND
• WHEN CHILD REACHES A MAXIMUM WEIGHT OF 30 LBS, THE CHANGING TRAY SHALL NO LONGER BE USED
• CHANGING PAD SIZED 32.50” X 17” X 1” FOR THIS PRODUCT
• USE A DRRESSER, SOLD SEPARATELY, FOR CHANGING TABLE TO ATTACH THE CHANGING TRAY
• ALWAYS SECURE THIS UNIT TO THE CHANGING SURFACE OF DRESSER #816 OR #838 OR #843 BY DREAM ON ME INC., OR A SURFACE THAT IS LEVEL, STABLE AND STRUCTURALLY SOUND WITH A MINIMUM SURFACE DIMENSIONS OF 20” X 58”

1532, S. Washington Avenue
Piscataway, NJ 08854
E-mail: info@evolurbaby.com

www.evolurbaby.com

Follow us on

@EvolurBaby
@evolurbaby

to get your nursery featured on our social media.

Enter our monthly giveaway!
Simply scan the QRcode to register.

Chat with us!
For any questions or concerns or feedback.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>