legrand WNAH10KITW1 Adorne Smart Switch Starter Kit Instruction Manual

legrand WNAH10KITW1 Adorne Smart Switch Starter Kit

REGULATORY INFORMATION

FCC NOTICE: This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesirable operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 10 mm between the transmitter’s radiating structure(s) and the body of the user or nearby persons.

NOTE: Any changes or modifications to this device that are not expressly approved by the manufacturer will void the warranty and the user’s authority to operate the equipment.

Contains FCC ID: 2AU5D982057
IC NOTICE: This device complies with Industry Canada license-exempt RSS standards. Operation is subject to the following two conditions:

1. This device may not cause interference; and
2. This device must accept any interference, including interference that may cause undesired operation of the device.

RF EXPOSURE STATEMENT: This equipment meets the SAR evaluation limits given in RSS-102 Issue 5 requirements at the minimum separation distance of 10 mm to the human body. Note: Any changes or modifications to this device that are not expressly approved by the manufacturer, will void the warranty and the user’s authority to operate the equipment.

• IC: 25764-982057
• HVIN: 982057

For more information and helpful how-to videos, visit www.adornemyhome.com/install.

Remove spacers from the frame. Since this switch fills the frame completely, you will not need the spacers. From the back of the frame, pinch the tabs on the spacer to release. Use only with Legrand adorneTM system.

INSTALLATION INSTRUCTIONS

Please read these instructions completely before you begin. This adorneTM device is designed for installation in standard electrical boxes. However, some of the installation methods vary slightly from traditional methods. If you do not understand these instructions or are unsure of your abilities, seek the assistance of a qualified electrician.

WARNING
To prevent severe shock or electrocution, always disconnect power at the service panel before beginning work.
When replacing existing switches, label wires before disconnecting. Disconnect old switch.

Single Pole
Identify the Common or Hot wire attached to the black screw. Identify the neutral wire attached to the silver-colored screw. Identify the Load wire attached to the copper-colored screw.

3-Way
For 3-Way application, secure the spare wire with a wire nut and pair your smart switch with a wireless switch PN WNAL23.

• If necessary, cut wires and strip insulation using stripping guide on back of dimmer.

WARNING
Failure to connect the ground wire will result in an unsafe installation that could lead to personal injury.

Connect frame ground wire to bare ground wire in box. Fold ground wires into back of box. Mount frame to wall box with screws provided. Tighten screws just enough to hold frame in place. Do NOT over-tighten.

TIPS

•  Pre-fold wires into wall box to make it easier to fit them in the box when switch is connected.

• Use caution to avoid marring wall surface with the metal frame.

• Connect new smart gateway as shown. Make sure the terminal holes are clear. Insert wires into terminals and torque terminal screws to 14-16 inch-pounds. Do NOT over-tighten.

Single Pole

• Connect the wire identified as Common/Hot in Step 1 to HOT.
• Connect the wire identified as Neutral in Step 1 to WHITE.
• Connect other wire to load.

WARNING: Do not pair different size wires in the same terminal. If you have different size wires, use a wire nut to add a 6 inch pigtail of the same gauge wire to the smaller gauge wire.

• Carefully fold wires into box. Snap the dimmer into frame.

NOTE – If you need to remove dimmer after snapping into frame, first remove frame from wall box to access the four locking tabs on the back of the dimmer. Insert a flat screwdriver to depress tabs as you apply pressure to push dimmer out.

Test the Smart Switch
NOTE: See getting to know your switch section for feature details. Turn the power back on at the circuit breaker, press switch to turn light on/off. This device is designed to work with the adorne® Smart Gateway with Netatmo.
Follow the instructions from your app to finish setting up your switch.
TROUBLESHOOTING TIP: If the device is not powering check wiring to determine if you have reversed the “HOT” and “LOAD” wiring.

Set up your System

• Download and launch the Legrand Home + Control app. The app is available on the App Store or on Google Play.
• Connect your smart device to your home network by following the step by step instructions in the app.
• Use the app to control your smart device.

Getting to Know Your Switch

of paddle to turn light off
2| LED Locator Light Voyant DEL| Used to initiate device setup. Marked with a “*” icon
3| EZ Button Bouton EZ| Used to enter setup mode

LED Indicator Light Explanation

Reset To Factory Default
Deleting a device from the app will reset it to factory defaults.
To manually reset the device to factory defaults press and hold the EZ button for 10 seconds until you see the LED blink red then release. The LED will change to solid red when the reset is complete.

Due to ongoing product improvements, Legrand reserves the right to change specifications without notice. For the most recent instruction sheets or more information on this product, please see this link or scan the QR code:
https://www.legrand.us/p/wnal10w1

Snap wall plate to frame.
There are three click-stops to adjust the fit of the wall plate to the dimmer and the wall.

NOTE: To remove wall plate, insert a small, flat screw-driver in notches on wall plate and twist gently to pry from frame.

Never apply cleaner directly to the device or wall plate. Apply to a soft cloth and use cloth to remove any smudges from the product.

Technical Assistance:877-295-3472
www.adornemyhome.com/install

LIMITED TWO-YEAR WARRANTY
Limited two-year warranty information for adorne products is available at www.legrand.us/adorne/warranty. Limited warranty information for adorneTM products may also be obtained free of charge by sending a written request, along with your proof of purchase (including purchase date), to:

Legrand
Attn: adorne Customer Service/Warranty Department 50 Boyd Avenue
Syracuse, NY 13209

No: 341332 – 08/21
© Copyright 2021 Legrand All Rights Reserved.
© Copyright 2021 Legrand Tous droits réservés Legrand.
© Copyright 2021 Legrand Legrand Todos los drechos reservados.

60 Woodlawn Street West Hartford, CT 06110 1.877.
BY.LEGRAND (295.3472)
www.legrand.us

CANADA
905.738.9195
www.legrand.ca

References

• Search Results Page
• Legrand US | Delivering and Managing Power, Light, and Data
• The adorne® Collection | Legrand
• adorne® Warranty ⎸Legrand
• Smart Switch with Netatmo ǀ Legrand

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>