NINJA NC301C Series Ice Cream Maker User Guide
- June 8, 2024
- Ninja
Table of Contents
NINJA NC301C Series Ice Cream Maker
Perfectly personalized ice cream
PREP: 5 minutes
FREEZE: 24 hours
PROGRAM TIME: 1 1/2 minutes
MAKES: 4 servings
INGREDIENTS
1 tablespoon (18 g) cream cheese
70 g granulated sugar
180 ml heavy cream
Flavoring, 1 teaspoon extract of your choice
OR 2 tablespoons of cocoa powder
240 ml whole milk
40 g of your favorite mix-ins (optional)
PICK YOUR FLAVOR
-
Cocoa powder
-
Vanilla extract
-
Mint extract
-
Almond extract
-
Fruit extract
MAKE IT DAIRY-FREE Use vegan cream cheese for cream cheese, unsweetened coconut cream for heavy cream, and unsweetened oat milk for milk. Whisk the coconut cream until smooth, then add the remaining ingredients.
-
Microwave the cream cheese for 10 seconds.
Add sugar and flavor, then whisk the mixture until it looks like frosting. -
Slowly mix in heavy cream and milk until sugar is dissolved.
-
Pour base into CREAMi™ Pint. Place lid on pint and freeze for 24 hours.
-
Remove lid from frozen pint.
Refer to next page for Assembly & Process instructions.
Select ICE CREAM.
PICK YOUR MIX-INS TO ADD A PERSONAL TOUCH
40 g of your favorite crushed candies, frozen fruits, chopped nuts, chocolate pieces, and more.
With a spoon, create a 4 cm wide hole that reaches the bottom of the pint.
Add mix-ins to the hole in the pint and process again using the MIX-IN
program.
Assembly & Process
-
Plug in unit first
The unit will NOT run if the outer bowl is installed before the unit is plugged in. -
Install
CREAMi™ Pint Remove lid from pint and check that the ingredients have not been frozen at an angle. Place the pint containing the frozen base in the outer bowl. -
Install
Creamerizer™ Paddle Press and hold the paddle latch on the top of the outer
bowl lid, then insert the paddle in the bottom of the lid. Release the latch to secure the paddle. -
Install lid
Position the tab of the lid just slightly to the right of the outer bowl handle so the lines on the lid and handle align. Rotate the lid clockwise to lock.
NOTE If programs will not illuminate, make sure the unit is properly assembled.
See the troubleshooting section of the safety instructions if install light is illuminated. -
Install outer bowl
After plugging in the unit, place the outer bowl on the base with the handle in the middle of the unit.
Twist handle to the right to raise the platform and lock the bowl in place. You should hear a click.
-
Select program
Press the power button, then select the program that suits your recipe. -
Remove bowl
When program ends, hold the release button on the left of the motor base and twist bowl handle clockwise to remove.
-
Remove lid
Press the lid unlock button and twist to remove lid. -
If adding mix-ins, use a spoon to create a 4 cm wide hole that reaches the bottom of the pint.
Add chopped or broken mix-ins to the hole in the pint and process again using the MIX-IN program.
If not adding mix-ins, RE-SPIN can be used on a crumbly or powdery pint to make it creamy.
RE-SPIN is often needed for very cold bases.
DO NOT RE-SPIN before using MIX-IN program.
Disassembly & Cleaning
Remove pint & paddle
Lift the pint out of the outer bowl.
Rinse the outer bowl lid to remove any sticky residue or pieces wedged in the
paddle.
Then remove the paddle by pressing the paddle latch on top of the lid.
All parts are dishwasher safe (top rack only) and can also be hand-washed.
Outer bowl lid
locks Creamerizer Paddle in place
Creamerizer™ Paddle
This dual functioning paddle finely shaves and mixes frozen ingredients into
the creamiest treats.
CREAMi™ Pints & Lids
BPA-free pints and lids for making and storing CREAMi treats.
Outer bowl
securely holds the pint in place during processing.
Customer service
GET HELP RIGHT NOW!
DON’T RETURN TO THE STORE.
Questions or Problems?
CALL US:
1-855-520-7816
Toll-free customer support line
Scan the code for online help, FAQs, recipes, and more.
Qr.ninjakitchen.com/creami-ca
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>