STERLING 1485067-2 B 2-Handle Brass Tub Shower Valve Stem Instruction Manual
- June 4, 2024
- STERLING
Table of Contents
STERLING 1485067-2 B 2-Handle Brass Tub Shower Valve Stem
Tools Requirement
Optional
- Mortar cement
- Shims
- Furring Strips
- Drop cloth
Record your model number below for future reference:
Observe all local building and plumbing codes.
INSTALLATION
Install on an adequately supported subfloor.
If the subfloor is not level and access to shim is difficult, install with a
1″ (25 mm) to 2″ (51 mm) bed of mortar cement.
- Construct a plumb stud pocket according to the roughing-in information on the back page.
- Install the rough plumbing.
- Install the drain to the bath. Position a protective liner in the bath basin.
- Staple the felt pad, if provided, to the subfloor so it will contact all the support feet.
- Without a pad, we recommend the basin area be set in 1″ (25 mm) to 2″ (51 mm) of mortar cement.
- Attach the apron brace, if provided. Lift and position the bath in the stud pocket.
- Attach metal support clips to the flange at the locations shown in the roughing-in information.
- Level the unit. Secure the metal support clips to the studs. Bend the tabs over the flange.
- Install plastic attachment clips at all remaining stud locations.
- With the unit level, shim under the support feet as needed.
- Connect the bath drain to the drain pipe. Position a protective liner in the bath basin.
- Custom Walls: Install furring strips, wallboard, and the finished wall as shown.
- Sterling Wall Set: Install the back wall. Insert the tabs into the slots.
- Sterling Wall Set: Measure, mark, and drill the faucet holes in the end wall.
- Apply an L-shaped bead of silicone sealant at each outside corner.
- Install the end walls. Engage the pins in the slots.
- The front edges should be flush, with no more than a 1/32″ (1 mm) gap.
- Starting at the bottom, install screws through the dimples to secure the flanges to the studs.
- Secure the walls to the studs along the top. Use shims as needed.
- Cover the framing with water-resistant wallboard. Install the finished wall material.
- Install the faucet trim and accessories, and seal where they contact the wall panels.
- After painting, apply 100% silicone sealant where the unit contacts the finished wall.
Dimension
| A | B | C | D | E | F | G |
|---|
71100110
71100120
| 17-1/4″ (438 mm)| 37-1/2″ (953 mm)| 73-1/4″ (1861 mm)| —| 8-3/4″ (222 mm)|
24-1/2″ (622 mm)| —
71101110
71101120
| 17-1/4″ (438 mm)| 37-1/2″ (953 mm)| —| —| 8-3/4″ (222 mm)| 24-1/2″ (622
mm)| —
71100112
71100122
| 17-1/4″ (438 mm)| 37-1/2″ (953 mm)| 75-1/2″ (1918 mm)| 3″
(76 mm)
| 8-3/4″ (222 mm)| 24-1/2″ (622 mm)| 2″
(51 mm)
71101112
71101122
| 17-1/4″ (438 mm)| 37-1/2″ (953 mm)| —| 3″
(76 mm)
| 8-3/4″ (222 mm)| 24-1/2″ (622 mm)| 2″
(51 mm)
71110110
71110120
| 20-1/4″ (514 mm)| 43-1/2″ (1105 mm)| 73-1/4″ (1861 mm)| —| 11-1/2″ (292
mm)| 27-1/2″ (699 mm)| —
71111110
71111120
| 20-1/4″ (514 mm)| 43-1/2″ (1105 mm)| —| —| 11-1/2″ (292 mm)| 27-1/2″ (699
mm)| —
71110112
71110122
| 20-1/4″ (514 mm)| 43-1/2″ (1105 mm)| 75-1/2″ (1918 mm)| 3″
(76 mm)
| 11-1/2″ (292 mm)| 27-1/2″ (699 mm)| 2″
(51 mm)
71111112
71111122
| 20-1/4″ (514 mm)| 43-1/2″ (1105 mm)| —| 3″
(76 mm)
| 11-1/2″ (292 mm)| 27-1/2″ (699 mm)| 2″
(51 mm)
Need help?
Contact the Customer Care Center.
USA/Canada: 1-800-STERLING
(1-800-783-7546), Mexico:
001-877-680-1310
For service parts information
visit sterlingplumbing.com/parts.
For care and cleaning,
- visit sterlingplumbing.com/care-and-cleaning.
- Patents: kohlercompany.com/patents
This product is covered under the STERLING® Vikrell® or Acrylic Baths and Shower Bases Ten-Year Limited Warranty found at sterlingplumbing.com/warranty. For a hard copy of warranty terms, contact the Customer Care Center.
References
- Care & Cleaning Tips for Kitchen & Bathroom | Sterling Plumbing
- Find Service & Replacement Parts | Sterling Plumbing
- View Warranty Info | Sterling Plumbing
- Showers, Tubs, Toilets, Sinks & More for Kitchen & Bath | Sterling Plumbing