Shuttle DH670 XPC BIOS Installation Guide
- June 8, 2024
- Shuttle
Table of Contents
Shuttle DH670 XPC BIOS
Copyright
No part of this publication may be reproduced, transcribed, stored in a retrieval system, translated into any language, or transmitted in any form or by any means such as electronic, mechanical, magnetic, optical, chemical, photocopy, manual, or otherwise, without prior written permission from Shuttle® Inc. Other brands and product names used herein are for identification purposes only and may be trademarks of their respective owners.
Disclaimer
Shuttle® Inc. shall not be liable for any incidental or consequential damages
resulting from the performance or use of this product.
Shuttle® Inc. makes no representation or warranty regarding the contents of
this manual. Information in this manual had been carefully checked for
accuracy ;however, no guarantee is given as to the correctness of the
contents. For continuing product improvement, Shuttle® Inc. reserves the right
to revise the manual or make changes to the specifications of this product at
any time without notice and obligation to any person or entity regarding such
change. The information contained in this manual is provided for general use
by customers.
This device complies to Part 15 of the FCC Rules. Operation is subject to the
following two conditions.
- This device may not cause harmful interference.
- This device must withstand any background interference including those that may cause undesired operation.
Trademarks
Shuttle is a registered trademark of Shuttle Inc.
Intel and Pentium are registered trademarks of Intel Corporation.
PS/2 is a registered trademark of IBM Corporation.
AWARD is a registered trademark of Award Software Inc.
Microsoft and Windows are registered trademarks of Microsoft Corporation.
General Notice
Other brand and product names used herein are for identification purposes only and may be trademarks of their respective owners.
Safety Information
Read the following precautions before setting up.
CAUTION
Incorrectly replacing the battery may damage this co-mputer. Replace only with the same or equivalent type recommended by the manufacturer. Disposal of used batteries according to the manufacturer’s instructions
Installation Notices
Do not place this device underneath heavy loads or in an unstable position.
Do not expose this device to high levels of direct sunlight, high-humidity or
wet conditions.
Do not use or expose this device around magnetic fields as magnetic
interference may affect the performance of the device.
Do not block the air vents to this device or impede the airflow in any way
Driver and Software Installation
Motherboard Driver DVD
The DVD contents attached in DH670 Series motherboard are subject to change without notice.
The Motherboard Driver DVD contains all the motherboard drivers necessary to
optimize the performance of this Shuttle Xvision in a Windows® OS. Install
these drivers after installing Microsoft® Windows®. Insert the attached DVD
into your DVD-ROM drive. The DVD AutoRun screen should appear. If the AutoRun
screen does not appear, double click on Autorun icon in My Computer to bring
up Shuttle Mainboard Software Setup screen.
Navigation Bar Description :
Auto Install Driver
Install Intel Rapid Storage Tech. Driver
User Manuals – Motherboard Manual, Quick Guide.
Link To Shuttle Website – Link to shuttle website homepage.
Browse This DVD – Allows you to see contents of this DVD.
User Manuals
Install Adobe Reader 9.5
Motherboard Manual
Quick Guide
Appendix
Starting BIOS
AMIBIOS has been integrated into many motherboards for over a decade. In the
past, people often referred to the AMIBIOS setup menu as BIOS, BIOS setup, or
CMOS setup.
American Megatrends refers to this setup as BIOS. Specifically, it is the name
of the AMIBIOS BIOS setup utility. This chapter describes the basic navigation
of the BIOS setup screens.
Enter the BIOS
To enter the BIOS setup screens, follow the steps below:
Step1. Power on the motherboard.
Step2. Press the key on your keyboard when you see the following text
prompt: Press DEL to run Setup.
Step3. After you press the key, the main BIOS setup menu displays. You
can access the other setup screens from the main BIOS setup menu, such as the
Chipset and Power menus.
This manual describes the standard look of the BIOS setup screen. The motherboard manufacturer has the ability to change any and all of the settings described in this manual. This means that some of the options described in this manual do not exist in your motherboard’s AMIBIOS.
In most cases, the key is used to invoke the BIOS setup screen. There are a few cases that other keys are used, such as ,, and so on.
BIOS Setup Menu
The main BIOS setup menu is the first screen that you can navigate. Each main
BIOS setup menu option is described in this user’s guide.
The Main BIOS setup menu screen has two main frames. The left frame displays
all the options that can be configured. “Grayed-out” options cannot be
configured.
Options is blue can be.
The right frame displays the key legend. Above the key legend is an area
reserved for a text message. When an option is selected in the left frame, it
is highlighted in white.
Often a text message will accompany it.
AMIBIOS has default text messages built into it. The motherboard manufacture retains the option to include, leave out, or change any of these text messages. They can also add their own text messages. Because of this, many screen shots in this manual are different from your BIOS setup screen.
The BIOS setup/utility uses a key-based navigation system called hot keys. Most of the BIOS setup utility hot keys can be used at any time during the setup navigation process. These keys include , , , , keys, and so on.
There is a hot key legend located in the right frame on most BIOS setup screens.
| Hot Key | Description |
|---|
→ Left
← Right
| The Left and Right
For example: Main screen, Advanced screen, Chipset screen, and so on.
↑ Up
↓ Down
| The Up and Down
screen.
+- Plus/Minus| The Plus and Minus
Tab| The
F1| The
F4| The
ESC| The
Enter| The
Main Setup
When you first enter the BIOS Setup Utility, you will enter the Main setup
screen.
You can always return to the Main setup screen by selecting the Main tab.
There are two Main Setup options. They are described in this section. The Main
BIOS Setup screen is shown below.
System Time/System Date
Use this option to change the system time and date. Highlight System Time or System Date using the keys. Enter new values through the keyboard. Press the key or the keys to move between fields. The date must be entered in MM/DD/YY format. The time is entered in HH:MM:SS format.
The time is in 24-hour format. For example, 5:30 A.M. appears as 05:30:00, and 5:30 P.M. as 17:30:00.
Advanced
Select the Advanced tab from the BIOS setup screen to enter the Advanced BIOS Setup screen. You can select any of the items in the left frame of the screen, such as CPU Configuration, to go to the sub menu for that item. You can display an Advanced BIOS Setup option by highlighting it using the keys. All Advanced BIOS Setup options are described in this section. The Advanced BIOS Setup screen is shown below. The sub menus are described on the following pages.
TPM Configuration
Security Device Support
This item allows user to enable/disable firmware TPM function.
- The choice: Enabled, Disabled.
Power Management Configuration
Wake Up by USB (S3)
This item allows you to enable or disable system wake up by USB (S3).
- The choice: Enabled , Disabled.
EuP Function
This item allows you to enable or disable system EuP function in S4/S5.
- The choice: Enabled , Disabled.
Power-On after Power-Fail
This item allows you to set system power on automatically after AC power
restored.
- The choice: Power On, Former-sts, Power Off, Power On by LAN, Power On
by RTC.
PowerOn by RTC Alarm
When enabled, System will wake on the hr::min::sec specified.
- The choice: Enabled , Disabled.
Wake Up by LAN
This item allows you to enable or disable system wake on by onboard LAN chip.
- The choice: Enabled , Disabled.
CPU Configuration
You can use this screen to select options for the CPU Configuration Settings. Use the up and down keys to select an item. Use the and keys to change the value of the selected option. A description of the selected item appears on the right side of the screen. The settings are described on the following pages. An example of the CPU Configuration screen is shown below.
The CPU Configuration setup screen varies depending on the installed processor.
Intel(R) V. T.
When enable, a VMM can utilize the additional hardware capabilities provided by vanderpool Technology.
- The choice: Enabled , Disabled.
CPU support, item appear.
Active Processor Cores
This item allows you to determine how many cores to be enabled.
- The choice: ALL,1.
Intel(R) HT Technology
This item allows you to enable or disable Intel(R) HT Technology.
- The choice: Enabled , Disabled.
EIST
This item allows you to enable or disable Enhanced lntel SpeedStep®
Technology.
- The choice: Enabled , Disabled.
Intel(R) Speed Shift Technology
This item allows you to enable or disable Intel(R) Speed Shift
Technology(ISST).
- The choice: Enabled , Disabled.
Turbo Mode
This item allows you to enable or disable lntel® Turbo Boost Technology.
- The choice: Enabled , Disabled
The CPU Configuration setup screen varies depending on the installed processor.
C State Support
This item allows you to enable or disable CPU C State.
- The choice: Enabled , Disabled.
SATA Configuration
SATA Mode
This item allows you to set the SATA Mode.
- The choice: AHCI or RAID.
Onboard Device Configuration
High Definition Audio
This item allows you to enable or disable system High Definition Audio.
- The choice: Enabled , Disabled.
CNVi Function
This item allows you to enable or disable CNVi interface function.
- The choice: Enabled , Disabled.
Onboard LAN1/2 Function
This item allows you to enable or disable LAN Function.
- The choice: Enabled , Disabled.
Onboard LAN BOOT ROM
This item allows you to enable or disable Onboard LAN BOOT ROM.
- The choice: Enabled , Disabled.
IGD Memory Size Select
Allows you to select the size of system memory used by the internal graphics
device.
- The choice: 32MB, 64MB, 128MB, 256MB, 512MB.
Intel(R) VT-d
This item allows you to enable or disable VT-d.
- The choice: Enabled , Disabled.
Serial Port Configuration
Option are in its sub-menu. Pressto enter the sub-menu of detailed options
Serial Port 1/2
This item allows you to enable or disable Serial Port.
- The choice: Enabled, Disabled.
Termination(120ohm)
This item allows you to enable or disable Termination(120ohm) function for
RS422/485..
The choice: Enabled, Disabled.
Hardware Health Configuration
FAN1 Speed Control
This item allows you to set Fan1 Speed.
- The choice: Smart Fan Mode, Ultra-Low Speed, Low Speed, Mid Speed, Full Speed.
Security
Select the Security tab from the BIOS setup screen to enter the Security BIOS Setup screen. You can display an Security BIOS Setup option by highlighting it using the keys. All Security BIOS Setup options are described in this section. The Security Setup screen is shown below. The sub menus are documented on the following pages.
Supervisor Password
Indicates whether a supervisor password has been set. If the password has been
installed, Installed displays. If not, Not Installed displays.
User Password
Indicates whether a user password has been set. If the password has been
installed, Installed displays. If not, Not Installed displays.
Change Supervisor Password
English Select Change Supervisor Password from the Security Setup menu and
press .
Enter New Password:
Type the password and press . The screen does not display the characters entered. Retype the password as prompted and press . If the password confirmation is incorrect, an error message appears. The password is stored in NVRAM after BIOS completes.
Change User Password
Select Change User Password from the Security Setup menu and press
Enter New Password:
Type the password and press . The screen does not display the characters entered. Retype the password as prompted and press . If the password confirmation is incorrect, an error message appears. The password is stored in NVRAM after BIOS completes.
Password Login control
This item allows user to adjust Password Login control.
- The choice: Boot, Setup, Both
Flash Write Protection
Choose [Enabled] to avoid virus destroy BIOS. If you want to flash BIOS, you
must set it [Disabled].
- The choice: Enabled or Disabled.
Secure Boot Control
This item allows you to enable or disable Secure Boot.
- The choice: Enabled, Disabled.
Boot
Select the Boot tab from the BIOS setup screen to enter the Boot BIOS Setup screen. You can select any of the items in the left frame of the screen, such as Boot Settings Configuration, to go to the sub menu for that item. You can display an Boot BIOS Setup option by highlighting it using the keys. All Boot BIOS Setup options are described in this section. The Boot BIOS Setup screen is shown below. The sub menus are described on the following pages.
Bootup Num-Lock
This item allows you to enable or disable keyboard Num-Lock state.
- The choice: Enabled, Disabled.
Boot from USB device
This item allows you to enable or disable boot from USB device.
- The choice: Enabled , Disabled.
Fast Boot Function
This item allows you to enable or disable Fast Boot Function.
- The choice: Enabled , Disabled.
Boot Device Priority (Boot Option #1/2/3/….)
Specifies the boot sequence from the available devices. A device enclosed in
parenthesis has been disabled in the corresponding type menu.
Exit
Select the Exit tab from the BIOS setup screen to enter the Exit BIOS Setup screen. You can display an Exit BIOS Setup option by highlighting it using the keys. All Exit BIOS Setup options are described in this section. The Exit BIOS Setup screen is shown below.
Save Changes and Exit
When you have completed the system configuration changes, select this option
to leave BIOS Setup and reboot the computer so the new system configuration
parameters can take effect.
Select “Save Changes and Exit” from the Exit menu and press . Save
Configuration Changes and Exit Now? [Ok] [Cancel] appears in the window.
Select Ok to save changes and exit.
Exit Without Saving Changes
Select “Exit without Saving Changes” from the Exit menu and press . Select Ok to discard changes and Exit.
Load Defaults Settings
BIOS automatically sets all BIOS Setup options to a complete set of default
settings when you Select this option. The Optimal settings are designed for
maximum system performance, but may not work best for all computer
applications. In particular, do not use the Optimal BIOS Setup options if your
computer is experiencing system configuration problems. Select Load Optimal
Defaults from the Exit menu and press . Select Ok to load optimal defaults.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>