ARISTON GGA24BKAUS Gas Cooktops Instruction Manual

June 4, 2024
Ariston

ARISTON GGA24BKAUS Gas Cooktops

ARISTON-GGA24BKAUS-Gas-Cooktops-PRODUCT

SAFETY INSTRUCTIONS

Download the complete instruction manual www. ariston.com.au or call the phone number shown on the warranty booklet .
Before using the appliance, read these safety instructions. Keep them nearby for future reference. These instructions and the appliance itself provide important safety warnings, to be observed at all times. The manufacturer declines any liability for failure to observe these safety instructions, for inappropriate use of the appliance or incorrect setting of controls.
These instructions are valid if the country symbol appears on the appliance. If the symbol doesn’t appear on the appliance, it is necessary to refer to the technical instructions which will provide the necessary instructions concerning of the appliance to the conditions of use of the country.
CAUTION : The use of the gas cooking appliance results in the production of heat, moisture and products of combustion in the room in which it is installed. Ensure that the kitchen is well ventilated especially when the appliance is in use: keep natural ventilation holes open or install a mechanical ventilation device (mechanical extractor hood). Prolonged intensive use of the appliance may call for additional ventilation, for example opening of the window, or more ventilation, increasing the level of mechanical ventilation where present.
WARNING: The appliance and its accessible parts become hot during use. Care should be taken to avoid touching heating elements. Children less than 8 years of age must be kept away unless continuously supervised.
WARNING : If the surface is cracked, switch off the appliance to avoid the possibility of electric shock.
WARNING: Danger of Do not store items on the cooking surfaces.
CAUTION : The cooking process has to be supervised. A short cooking process has to be supervised continuously.
WARNING : Unattended cooking on a hob with fat or oil can be dangerous – risk of NEVER try to extinguish a with water, but switch the
blanket.
Do not use the hob as a work surface or support. Do not use or store materials in or near this appliance.
If the information in this manual is not followed exactly, a or explosion may result causing property damage or injury.
Very young children (0-3 years) should be kept away from the appliance. Young children (3-8 years) should be kept away from the appliance unless continuously supervised. Children from 8 years old and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge can use this appliance only if they are supervised or have been given instructions on safe use and understand the hazards involved. Children must not play with the appliance. Cleaning and user maintenance must not be carried out by children without supervision.
CAUTION: In case of hotplate glass breakage:-shut immediately all burners and any electrical heating element and isolate the appliance from the power supply; – do not touch the appliance surface; -do not use the appliance.
In case the appliance has a glass lid, it can break in if it is heated up. Turn all the burners and the electric plates before closing the lid. Do not shut down lid when burner is alight.

  • DO NOT SPRAY AEROSOLS IN THE VICINITY OF THIS APPLIANCE WHILE IS IN OPERATION .
  • DO NOT MODIFY THIS APPLIANCE.
  • DO NOT USE THIS APPLIANCE AS A SPACE HEATER.
  • DO NOT USE OR STORE FLAMMABLE MATERIALS

NEAR THIS APPLIANCE.
PERMITTED USE

  • CAUTION: the appliance is not intended to be operated by means of an external switching device, such as a timer, or separate remote controlled system.
  • This appliance is intended to be used in household and similar applications such as: kitchen areas in shops, and other working environments; farm houses; by clients in hotels, motels, bed & breakfast and other residential environments.
  • No other use is permitted (e.g. heating rooms).
  • This appliance is not for professional use. Do not use the appliance outdoors.
  • Use pots and pans with bottoms the same width as that of the burners or slightly larger (see table). Make sure pots on the grates do not protrude beyond the edge of the hob.
  • Improper use of the grids can result in damage to the hob: do not position the grids upside down or slide them across the hob.
  • If the hob surface is in glass material, do not use the cast iron griddles, ollar stones, terracotta pots and pans.
  • Do not use: heat such as metal mesh, or any other types; two burners simultaneously for one receptacle (e.g. Fish kettle).
  • Should particular local conditions of the delivered gas make the ignition of  In case of installation of a hood above the cooktop, please refer to the hood instructions for the correct distance.
  • The protective rubber feet on the grids represent a choking hazard for young children. After removing the grids, please ensure that all the feet are

INSTALLATION

The appliance must be handled and installed by two or more persons – risk of injury. Use protective gloves to unpack and install – risk of cuts.
Installation, including water supply (if any) and electrical connections, and repairs must be carried out user manual. Keep children away from the installation site. After unpacking the appliance, make sure that it has not been damaged during transport. In the event of problems, contact the dealer or your nearest After-sales Service. Once installed, packaging waste (plastic, styrofoam parts etc.) must be stored out of reach of children – risk of The appliance must be disconnected from the power supply before any installation operation – risk of electrical shock. During installation, make sure the appliance does not damage the power cable – risk of or electrical shock. Only activate the appliance when the installation has been completed. The electrical and gas connections must comply with local regulation.

  • WARNING: of the appliance and its method of installation are essential in order to use the appliance safely and correctly in all the additional countries.
  • Use pressure regulators suitable for the gas pressure indicated in the instruction.
  • The room must be equipped with an air extraction system that expels any combustion fumes.
  • The room must also allow proper air circulation, as air is needed for combustion to occur normally. The of air must not be less than 2 m3/h per kW of installed power.
  • The air circulation system may take air directly from the outside by means of a pipe with an inner cross section of at least 100 cm2; the opening must not be vulnerable to any type of blockages.
  • The system can also provide the air needed for combustion indirectly, i.e. from adjacent rooms with air circulation tubes as described above. However, these rooms must not be communal rooms, bedrooms
  • Liquid petroleum gas sinks to the as it is heavier than air. Therefore, rooms containing LPG cylinders must also be equipped with vents to allow gas to escape in the event of a leak. As a result LPG cylinders, whether partially or completely full, must not be installed or stored in rooms or storage areas that are below ground level (cellars, etc.). It is advisable to keep only the cylinder being used in the room, positioned so that it is not subject to heat produced by external sources (ovens, stoves, etc.) which could raise the temperature of the cylinder above 50°C.
  • Carry out all cabinet cutting works before the appliance in the furniture and remove all wood chips and sawdust.
  • If the appliance is not installed above an oven, a separator panel (not included) must be installed in the compartment under the appliance.
    Should you experience in turning the burner’s knobs, please contact After Sales Service for replacement of the burner tap if found to be faulty. The openings used for the ventilation and dispersion of heat must never be covered.

GAS CONNECTION

  • WARNING: Prior to installation, ensure that the local distribution conditions (nature of gas and gas pressure) and the adjustment of the appliance are compatible.

  • Check that the pressure of the gas supply is consistent with the values indicated in Injectors Table.

  • WARNING: The adjustment conditions for this appliance are stated on the label (or data plate).

  • WARNING: This appliance is not connected to a combustion products evacuation device. It shall be installed and connected in accordance with current installation regulations. Particular attention shall be given to the relevant requirements regarding ventilation.

  • If the appliance is connected to liquid gas, the regulation screw must be fastened as tightly as possible.

  • IMPORTANT: When gas cylinder is adopted, the gas cylinder or gas container must be properly settled (vertical orientation).

  • The cooktop is not suitable for use with aftermarket lid or cover.

  • Use only or rigid metal hose for gas connection.

  • Connection with a rigid pipe (copper or steel): Connection to the gas system must be carried out in such a way as not to place any strain of any kind on the appliance. There is an adjustable L-shaped pipe on the appliance supply ramp and this is with a seal in order to prevent leaks. The seal must always be replaced after rotating the pipe (the seal is provided with the appliance). The gas supply pipe is a threaded 1/2 gas cylindrical male attachment.

  • Connecting a jointless stainless steel pipe is a threaded 1/2 gas cylindrical male attachment. These pipes must be installed so that they are never longer than 2000 mm when fully extended. Once connection has been carried out, make sure that the
    metal pipe does not touch any moving parts and is not compressed. Only use pipes and seals that comply with current National regulations.

  • IMPORTANT: If a stainless steel hose is used, it must be installed so as not touch any moving part of the furniture (e.g. drawer). It must pass through an area where there are no obstructions and where it is possible to inspect it on all its length.

  • The appliance should be connected to the main gas supply or to gas cylinder in compliance with the current National regulations. Before carry out the connection, make sure that the appliance is compatible with the gas supply you wish to use.

ADAPTING TO DIFFERENT TYPES OF GAS
In order to adapt the appliance to a type of gas other than the type for which it was manufactured (indicated on the rating plate), follow the dedicated steps provided after installation drawings.

ELECTRICAL WARNINGS

IMPORTANT: The data relevant to the voltage and power absorptions are indicated on the rating plate. The power cable must be long enough to connect the appliance, once in its housing, to the main power supply. Do not pull the power supply cable. It must be possible to disconnect the appliance from the power supply by unplugging it if plug is accessible, or by a multi-pole switch installed upstream of the socket in accordance with the wiring rules and the appliance must be earthed in conformity with national electrical safety standards. Do not use extension leads, multiple sockets or adapters. The electrical components must not be accessible to the user after installation. Do not use the appliance when you are wet or barefoot. Do not operate this appliance if it has a damaged power cable or plug, if it is not working properly, or if it has been damaged or dropped. If the supply cord is damaged, it must be replaced with an identical one by the manufacturer, its service agent or similarly persons in order to avoid a hazard – risk of electrical shock.

CLEANING AND MAINTENANCE

WARNING: Ensure that the appliance is switched and disconnected from the power supply before performing any maintenance operation; never use steam cleaning equipment – risk of electric shock.
Do not use abrasive or corrosive products, chlorine- based cleaners or pan scourers.

DISPOSAL OF PACKAGING MATERIALS
The packaging material is 100% recyclable and is marked with the recycle symbol .
The various parts of the packaging must therefore be disposed of responsibly and in full compliance with local authority regulations governing waste disposal.

DISPOSAL OF HOUSEHOLD APPLIANCES
This appliance is manufactured with recyclable or reusable materials. Dispose of it in accordance with local waste disposal regulations. For further information on the treatment, recovery and recycling of household electrical appliances, contact your local authority, the collection service for household waste or the store where you purchased the appliance. This appliance is marked in compliance with European Directive 2012/19/EU, Waste Electrical and Electronic Equipment (WEEE). By ensuring this product is disposed of correctly, you will help prevent negative consequences for the environment and human health. The symbol on the product or on the accompanying documentation indicates that it should not be treated as domestic waste but must be taken to an appropriate collection center for the recycling of electrical and electronic equipment.

ENERGY SAVING TIPS

  • Use pots and pans with bottom width equal to that of the cooking zone.
  • When possible, keep pot lids on during cooking.
  • Use a pressure cooker to save even more energy and time.
  • Place the pot in the middle of the cooking zone marked on the hob.

INJECTORS TABLE


BURNERS

| ****


GAS

| NORMAL PRESSURE

(kPa)

| INJECTOR DIAMETER

(1/100 mm)

| NOMINAL HEAT

INPUT (MJ/h)

MAX.

---|---|---|---|---
| DESCRIPTION



1

| ****


ULTRA RAPID

| ****

U-LPG NATURAL

| ****

2.75

1.00

| ****

100 B

175 B

| ****

12.6

14.5

| | ****

U-LPG

| ****

2.75

| ****

91

| ****

10.4

2| RAPID| NATURAL| 1.00| 155| 12.0



3

| ****

SEMIRAPID REDUCED

| ****

U-LPG NATURAL

| ****

2.75

1.00

| ****

60

105

| ****

4.9

5.4

| | ****

U-LPG

| ****

2.75

| ****

70

| ****

6.3

4| SEMIRAPID| NATURAL| 1.00| 120| 7.1



5

| ****


AUXILIARY

| ****

U-LPG NATURAL

| ****

2.75

1.00

| ****

53

90

| ****

3.6

4.1

INSTALLATION

TECHNICAL INFORMATION FOR THE INSTALLER

  • Use protective gloves for handling, preparing, and installing the product.
  • This product can be embedded in a worktop 20 ÷ 60 mm thick.
  • If there is no oven beneath the hob, insert a separator panel with a surface at least equal to the opening in the work surface. This panel must be positioned at a maximum distance of 150 mm below the upper surface of the work surface but, in no case, less than 70 mm from the bottom of the hob. If you intend to install an oven beneath the hob, make sure that it is equipped with a cooling system.
  • Where the rating plate is obscured by cabinetry when the cooktop is in the installed position, place the duplicate rating plate (provided together with the literature) on a surface of the cabinetry adjacent to the cooktop.

DIMENSIONS AND DISTANCES TO BE MAINTAINED

ARISTON GGA24BKAUS Gas
Cooktops fig 1

The appliance belongs to class 3 and is therefore subject to al l the provisions established by the provisions governing such appliances.
NOTE: In case of installation of a hood above the cooktop please refer to the range hood instructions for the correct distance. Clearance A, between the highest part of the highest burner of the gas cooking appliance and a range hood or exhaust fan (overhead clearance), shall be no less than 600 mm for a range hood, and no less than 750 mm for an exhaust fan. The minimum clearance from a combustible surface shall be a 200 mm horizontal distance from the periphery of any gas burner (AS/NZS 5601.1).ARISTON GGA24BKAUS Gas Cooktops
fig 2

If that horizontal clearance is less than 200 mm, that vertical surface must be protected by a non combustible material for 150 mm above the cooktop surface across the entire length (depth, width).
The shown area indicates the protected surface, which may be ceramic tiles or other approved material.ARISTON GGA24BKAUS Gas Cooktops fig
3

ASSEMBLY

Position the hob in the worktop opening made respecting the dimensions indicated in the Instruction. Never leave the packaging materials (cardboard, bags, polystyrene foam, nails, etc.) within children’s reach since they could become potential sources of danger. The cooktop has a special seal which prevents liquid from getting into the cabinet. Strictly comply with the following instructions in order to correctly apply this seal:
Cut the seal in 4 parts of the necessary length to positionning it on the 4 edges of the glass.ARISTON GGA24BKAUS Gas Cooktops fig
5

GAS CONNECTION

Before installation, check that the gas type (natural gas or Universal LPG) of the cooker is suitable for the gas type available for the installation. Check that the gas supply pressure is consistent with the values indicated in the “Injectors table.” This will ensure the safe operation and longevity of your appliance (in compliance with ISO 7 thread).
For NG models, the gas supply is connected to a regulator, which is supplied. The inlet connection has ½” B.S.P female thread. THE ELBOW ON THE APPLIANCE MUST BE HELD FIRMLY WITH A SPANNER. DO NOT OVER TIGHTEN. The regulated pressure for NG is 1.00kPa.
event of an emergency or service.
The gas connection is located in the rear and on the right hand underside of these appliances: 24 mm (mod: GGA24BKAUS),
230 mm (mod: GGA34BKAUS)If installing with a hose assembly, install with a hose assembly that complies with AS/NZS 1869, 10mm ID, class B or D, no more than 1.2m long and in accordance with AS/NZS 5601. Ensure that the hose does not contact the hot surfaces of the hot plate, oven, dishwasher or any other appliance that may be installed underneath or next to the hot plate. The hose should not be subjected to abrasion, kinking or permanent deformation and should be able
connections tested for gas leaks.

Natural Gas
Natural Gas installations require the connection of a gas regulator at the appliance. This regulator is supplied with the appliance on purchase. Assemble
supply side of the regulator must be provided by the installer.ARISTON
GGA24BKAUS Gas Cooktops fig 6

After installing the gas supply and making all connections check thoroughly for possible leaks. Turn all control knobs on the unit to the “OFF” position. Open the valve on the gas supply. Using a soap and water solution,

  • Burner cap on correctly
  • Burner positioned correctly
  • Burner vertically aligned with injector nipple

In some cases, the burners will fail to ignite immediately and seem to blow lightly when they do ignite; this is usually due to air in the gas pipe, which should clear itself within seconds of operation. If satisfactory performance cannot be obtained after following the instructions given, contact your After Sales Service for advice and assistance.

ELECTRICAL CONNECTION

IMPORTANT: the appliance must be installed following the manufacturer’s instructions. The manufacturer will not be liable for injury to persons or animals or property damage caused by an incorrect installation. of the appliance 380 mm from the right hand side. The voltage and power consumption are detailed on the underside of the appliance. Ensure that the appliance is correctly rated to the supply. Connect appliance by way of a switched power point.

THE APPLIANCE MUST BE EARTHED

Warning: in order to avoid any hazard, any electrical work performed on this equipment or its persons. The socket outlet for this cooktop shall be installed near the cooktop and shall be easily accessible.
The electrical connections ofthe appliance must be carried out in compliance with the provisions and standards in force.
Before connecting the appliance, check that:

  • The voltage matches the value shown on the rating plate and the section of the wires of the electrical system can support the load, which is also indicated on the rating plate.
  • The electrical capacity of the mains supply and current sockets suit the maximum power rating of the appliance (consult the data label applied to the underside of the cooktop).

When the appliance is connected straight to the electricity main:

  • Install an omnipolar circuit-breaker between the appliance and the electricity main. This circuitbreaker should be sized according to the load rating of the appliance and possess a minimum 3 mm gap between its contacts.
  • Remember that the earth wire must not be interrupted by the circuit-breaker.
  • Before performing any service on the electrical part of the appliance, it must absolutely be disconnected from the electrical network.

CAUTION!
The manufacturer cannot be responsible for the missing earthing of the appliance. Electrical connection must be carried out in compliance with local regulations. This appliance must be connected directly to the mains supply. Ensure the appliance is installed by an authorised person in accordance with AS/NZS 3000 wiring rules. “The devices intended to ensure the omnipolar disconnection of the cooktop from the supply network must comply with the requirements of the AS/NZS 3000”. Always disconnect the appliance from the electricity main before making any adjustments. All seals must be replaced by the technician at the end of any adjustments or regulations.
Our burners do not require primary air adjustment

  1. Data Label
    The Data Label is located on the underside of the cooktop. A duplicate Data Label is supplied to adhere in an accessible area next to the cooktop. This cooktop is suitable for Natural Gas and Universal LP Gas; ensure that the available gas supply matches the Data Label.

  2. Before Leaving
    instruct the user on the correct method of operation. In case the appliance fails to operate correctly after all checks have been carried out, refer to the authorised service provider in your area.

PRODUCT DESCRIPTION

ARISTON GGA24BKAUS Gas Cooktops fig
8

  1. Ultra rapid gas burner/WOK
  2. Rapid gas burner
  3. Semirapid reduced gas burner
  4. Semirapid gas burner
  5. Auxiliary gas burner
  6. Pan stands support 2F
  7. Pan stands support 1F
  8. Burner n° 2 control knob
  9. Burner n° 5 control knob
  10. Burner n° 1 control knob
  11. Burner n° 3 control knob
  12. Burner n° 4 control knobARISTON GGA24BKAUS Gas Cooktops fig 9

DAILY USE

  • This product is not to be installed in marine crafts, caravans, or mobile homes.

Abnormal operations:
Any of the following are considered to be abnormal operation and may require servicing:

  • Burners not igniting properly.
  • Burners failing to remain alight.
  • Burner extinguished by cupboard doors.
  • The knob must not be pressed for more than 15 sec. If, after that time has elapsed, the burner does not remain lit, wait at least one minute before trying to light it again.

HOW TO USE THE HOB

IMPORTANT: when the hob is in use, the entire hob area may become hot.

  • To ignite one of the burners, turn the relative knob anti-clockwise to
  • Press the knob against the control panel to ignite the burner.
  •  After the burner has ignited, keep the knob pressed for about 5-10 seconds to allow proper device operation.

The burner might go out when the knob is released. This means that the safety device has not warmed up enough. In this case, repeat the operations described above.

  • make sure pots on the grates do not protrude beyond the edge of the hob;
  • in the case of pans with convex bottoms (WOK), use a support grille, which should be positioned only on the ultra rapid burner;
  • avoid accidentally knocking the hob with pans, racks, or other kitchen utensils;
  • do not leave empty steak grills over the lit burner for longer than 5 minutes.

IMPORTANT: improper use ofthe grids can damage the hob: do not position the grids upside down or slide them across the hob.

BURNER Ø COOKWARE DIAMETER
Ultra rapid burner From 24 to 26 cm
Rapid From 20 to 22 cm
Semi-rapid From 16 to 18 cm
Auxiliary From 10 to 14 cm

ARISTON GGA24BKAUS Gas Cooktops fig 10

ADAPTING TO DIFFERENT TYPES OF GAS EN

  • injector not supplied with the appliance must be ordered from After Sales Service;
  • adjust the minimum setting of the taps.

NOTE: when liquid petroleum gas is used (ULPG), the minimum gas setting screw must be tightened as far as it will go.

  1. Remove each burner cap and burner skirt.
  2. Remove the Universal LP Gas main injector with a 7 mm/VF tube spanner and replace with the appropriate size Natural Gas injector for each burner. The following injector sizes are required for Natural Gas:

NATURAL GAS TO UNIVERSAL LP GAS CONVERSION PROCEDURE Appliance models: Gas vitroceramic cooktop models:

  1. Remove each burner cap and burner skirt.
  2. Remove the Natural Gas main injector with a 7 mm/VF tube spanner and replace with the appropriate size Universal LP Gas main injector for each burner. The following injector sizes are required for Universal LP Gas:
  3. Remove the control knob, with a thin shaft blade screwdriver down the centre of each gas valve shaft. screw the by-pass injector fully clockwise.
  4. Disconnect gas inlet pipe from the Natural Gas Regulator.
  5. Remove the Natural Gas Regulator from the appliance.
  6. Adjust the gas pressure to 2.75 kPa.
  7. If not already removed, remove the “Only for use with Natural Gas” label adhered to the bottom panel near the gas connection.
  8. Fit the new data label included in the gas conversion kit.

For the sake of convenience, the injector table also lists the heat inputs of the burners, the diameter of the injectors and the working pressures of the various types of gas.

It is understood that only burners operating with Natural gas should be subjected to the above mentioned adjustments.
The screw must be fully locked when the burners operate with Liquid gas.
Upon completion of adjustment, reseal using sealing wax or an equivalent material. ARISTON GGA24BKAUS Gas Cooktops fig 13

WOK ADAPTER
Use the WOK adapter (included) only on the ultra rapid burner. WOK PAN is not included.

MAINTENANCE AND CLEANING

Disconnect the appliance from the power supply.

CLEANING THE HOB SURFACE

  • All the enamelled and glass parts should be cleaned with warm water and a neutral solution.
  • Clean with warm water and neutral detergent, and then dry with a soft cloth or chamois.
  • Do not use abrasive or corrosive products, chlorine-based cleaners, or pan scourers.
  • Do not use steam cleaning appliances.
  • Do not leave acid or alkaline substances, such as vinegar, mustard, salt, sugar, or lemon juice on the hob.

CLEANING THE HOB PARTS

  • Clean glass and enamelled parts only with soft cloth or sponge.
  • Grids, burner caps, and burners can be removed to be cleaned.
  • Clean them by hand with warm water and non-abrasive detergent, removing any food residues and checking that none of the burner openings is clogged.
  • Rinse and dry.
  • When replacing the grids, make sure that the panstand area is aligned with the burner.
  • Models equipped with electrical ignition plugs and safety device require thorough cleaning of the plug end in order to ensure correct operation. Check these items frequently, and if necessary, clean them with a damp cloth. Any baked-on food should be removed with a toothpick or needle.

WARNINGS
Comply with the following instructions, before remounting the parts:

PREVENTATIVE MAINTENANCE
This cooktop should not require ongoing maintenance provided you ensure

  • All spillages are cleaned up as soon as they occur.
  • Burner are kept clean.
  • Burner ports are free of debris, food or anything else that may cause an obstruction.
  • Electrode and thermocouples are kept clean.
  • Burners are re-assembled correctly.
  • Do not get water in the area where the injectors are located.

TROUBLESHOOTING

If the hob does not operate correctly, before calling the After-Sales Service, refer to the Troubleshooting Guide to determine the problem.

  • the gas or electrical supplies are not shut  and especially that the  gas supply tap is open;
  • the gas cylinder (liquid gas) is not empty;
  • the burner openings are not clogged;
  • the plug end is not dirty;
  • there are no draughts near the hob.

The burner does not stay lit Check that :

  • when lighting the burner, the knob has been pressed for enough time to activate the protection device;
  • the burner openings are not clogged near the thermocouple;
  • the end of the safety device is not dirty;
  • the minimum gas setting is correct (see relevant paragraph).

The containers are not stable

  • the container is centred on the burner;
  • the grids have not been exchanged or positioned incorrectly.
  • If after the above checks the fault still occurs, get in touch with the nearest After Sales Service.

AFTE SALES SERVICE

IF AFTER THE ABOVE CHECKS THE FAULT STILL OCCURS, GET IN

To receive assistance, call the number shown on the warranty booklet or follow the instructions on the website www.ariston.com.au.
When contacting our Client After-sales service, always specify:

  • a brief description of the fault;
  • the type and exact model of the appliance;
  • the serial number (number after the word SN on the rating plate located under the appliance). The serial number is also indicated in the documentation;
  • your full address;
  • your telephone number.

WIRING DIAGRAM

ARISTON GGA24BKAUS Gas Cooktops fig
16

If any repairs are required, please contact an authorized after-sales service (to guarantee that original spare parts will be used and repairs carried out correctly).
ARISTON
PRIORITY SERVICE
If you are not completely satisfied with your appliance or require service call:
Australia
Phone: 1300 762 219
www.ariston.com.au

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals