MAXIM LIGHTING 994392WT 44 Inch Ceiling Fan Instruction Manual

: June 8, 2024
: MAXIM LIGHTING

MAXIM LIGHTING 994392WT 44 Inch Ceiling Fan

Please consult your electrician for hanging fixture and wiring.

Safety Information

To reduce the risk of electric shock, ensure the electricity has been turned off at the circuit breaker or fuse box before you begin.
All wiring must be in accordance with the National Electrical Code ANSI/NFPA 70-1999 and local electrical codes. Electrical installation shoule be performed by a qualified licensed electrician.
The outlet box and support structure must be securely mounted and capable of reliably supporting 35 lbs. (15.9kg). Use only UL Listed outlet boxes marked “Acceptable for Fan Support of 35 lbs.(15.9kg) or less.”
The fan must be mounted with a minimum of 7 ft. (2m) clearance from the trailing edge of the blades to the floor.
Do not operate the reversing switch while the fan blades are in motion. You must turn the fan off and stop the biades before you reverst the blade direction.
Do not place objects in the path of the blades.
Electrical diagrams are for reference only. Lighe kits that are not packed with the fan must be UL-listed and marked suitable for use with the model fan you are installing. Switches must be UL General Use Switches.Refer to the instructions packaged with the light kits and switches for proper assembly.
After making electrical connections, spliced conductors should be turned upward and pushed carefully up into the outlet box. The wires should be spread apart with the grounded conductor and the equipment-grounding conductor on ine side of the outlet box.
All setscrews must be checked and retightened where necessary before installation.

NOTE: These are approximate measures. They do not include the Amps and Wsttage used by the light kit.

WARNING: To reduce the risk of personal injury, do not bend the blade brackets (also referred to as flanges) during assembly or after installation. Do not insert objects in the path of the blades.

WARNING: Remove the rubber motor stops on the bottom of the fan before installing the blades or testing the motor.

WARNING: To reduce the risk of fire or electric shock, do not use this fan with any solid-state speed control device.

WARNING: To avoid possible electrical shock, turn the electricity off at the main fuse box before wiring. lf you feel you do not have enough electrical wiring knowledge or experience, contact a licensed electrician.

WARNING: Electrical diagrams are for reference only. Optional use of any light kit shall be UL-listed and marked suitable for use with this fan.

WARNING: To reduce the risk of fire, electric shock, or personai injury, mount to outiet box marked “Acceptable for fan Support of 35 lbs.(15.9kg) or less,” and use the screws provided with the outlet box.

CAUTION: To reduce the risk of personal injury, use only the screws provided with the oufiet box.

CAUTION: To avoid personal injury or damage to the fan and other items, use caution when working around or cleaning the fan.

TOOLS REQUIRED

MAXIM-LIGHTING-994392WT-44-Inch-Ceiling Fan-1

HARDWARE INCLUDED

MAXIM-LIGHTING-994392WT-44-Inch-Ceiling Fan-2

NOTE: Hardware not shown to actual size.

Part	Description	Quantity
AA	Blade bracket screw	1
BB	Wire connecting nut	3
CC	Wood screw	4
UU	Mounting screws	2

PACKAGE CONTENTS

MAXIM-LIGHTING-994392WT-44-Inch-Ceiling Fan-3

Part	Description	Quantity
A	Slide-on mounting bracket (inside canopy)	1
B	Fan-motor assembly	1
C	Blade	3
D	light kit pan	1
E	LED light kit	1
F	Glass bowl	1
G	Wall control	1

MOUNTING OPTIONS

WARNING: To reduce the risk of fire, electric shock, or personai injury, mount to outiet box marked “Acceptable for fan Support of 35 lbs.(15.9kg) or less,” and use the screws provided with the outlet box. An outlet box commonly used for the support of lighting fixtures may not be acceptable for fan support and may need to be replaced. lf in doubt, consult a qualified electrician.
If your ceiling fan does not have an existing UL-listed mounting box, then install one using the following instructions:

Disconnect the power by removing the fuses or turning off the circuit breakers.
Secure the outlet box directly to the building structure. Use the appropriate fasteners and materials. The outlet box and support structure must be securely mounted and capable of reliably supporting 35 lbs. (15.9kg). Use only UL Listed outlet boxes marked “Acceptable for Fan Support of 35 lbs. (15.9kg) or less.” . Do not use a plastic outlet box.

The illustrations below show three different ways to mount the outlet box.

NOTE: You may need a longer downrod to maintain proper blade clearance when installing on a steep, sloped ceiling. The maximum angle allowable is 30° away from horizontal.

If the canopy touches the downrod, then remove the decorative canopy bottom cover, and turn the canopy 180° before attaching the canopy to the mounting plate.
To hang your fan where there is an existing fixture but no ceiling joist, you may need an installation hanger bar as shown above.

Assembly – Standare Ceiling Mount

Preparing for mounting

Remove the mounting bracket (A) from the Fan-motor assembly (B) by loosening the two canopy screws (JJ) located in the round holes.
Remove and save the two canopy screws (II) in the “L” shaped slots. This will enable you to remove the mounting bracket (A).

Attaching the fan to the electrical box

WARNING: To reduce the risk of fire, electric shock or personal injury, mount to outlet box marked “Acceptable for fan support of 35 lbs. (15.9kg) or less”, and use screws provided with the outlet box.

Pass the 120-Volt supply wires through the center hole in the mounting bracket (A).
Install the ceiling mounting bracket on the outlet box by sliding the mounting bracket (A) over the two screws (UU) provided with the outlet box. lf necessary, use leveling washers (not included) between the mounting bracket (A) and the outlet box. Note that the flat side of the mounting bracket (A) is toward the outlet box. When using close-to-ceiling mounting, it is important that the mounting bracket be level.
Securely tighten the two mounting screws (UU).

Hanging the fan

WARNING: The hook (MM) on the mounting bracket is only to hang the fan while making the electrical connections. Failure to hang as shown may result in the hook (MM) breaking, causing the fan to fall. The hook must pass from the inside to the outside of the canopy.

WARNING: When hanging the fan on the hook (MM) it is critical that you use one of the non-slotted (round) holes in the Fan-motor assembly (B).

Carefully lift the fan-motor assembly (B) up to the slide-on mounting bracket (A).
Put the fan-motor assembly (B) assembly onto the mounting plate’s J hook (MM).
provided by utilizing one of the round holes at the outer rim of the Fan-motor assembly (B).hang the fan on the J hook (MM).

Making the electrical connections

WARNING: Each wire nut supplith this fan is designed to accept up to one 12-gauge house wire and two wires from the fan. lf you have larger than 12-gauge house wiring or more than one house wire to connect to the fan wiring consult an electrician for the proper size wire nuts to use.

WARNING: Remove the rubber motor stops on the bottom of the fan before installing the blades or testing the motor.

IMPORTANT: Use the plastic wire connectors (BB) supplied with your fan. Secure the connectors with electrical tape and ensure there are no loose strands or connections.

The fan comes with 18 in .Lead wires for use with assembly. you can cut the lead wires to your desired length This will make extra room in the fan-motor assembly (B) , if you do not wish to cut the wires, you will need to neatly wrap them.
Connect the fan motor green wires to the household green or bare wire using a wire connecting nut (BB).
Connect the fan motor white wire to the household white wire using a wire connecting nut (BB).
Connect the fan motor black and blue wires to the household black wire using a wire connecting nut (BB).
Secure each wire connecting nut using electrical tape.
Turn the wire connecting nut (BB) upward and push the wiring into the Junction box.

Mounting the fan-motor assembly (close-to-ceiling mount)

WARNING: The locking slots of ceiling canopy are provided only as an aid to mounting. Do not leave the fan assembly unattended until all four canopy screws are engaged and firmly tightened.

Carefully unhook the fan from the mounting bracket (A) and align the locking slots of the fan-motor assembly
(B) with the two screws (II) in the mounting bracket (A). Push up to engage the slots and turn clockwise to lock in place. Immediately tighten the two mounting screws firmly.
Install the other two mounting screws (JJ) (saved from Assembly Step 1 “Prepairing for mounting”) into the holes in the fan-motor assembly (B) and tighten firmly.

Fastening the blades to the motor

WARNING: Remove the rubber motor stops on the bottom of the fan before installing the blades or testing the motor.

Fasten the blade (C) to the fan-motor assembly (B) by the blade bracket screws(AA).
Repeat this step for the remaining blade bracket.

Attaching the light kit fitter assembly

CAUTION: To reduce the risk of electric shock, disconnect the electrical supply circuit to the fan before installing the light fixture.

Remove the three screws (VV) from the fan – motor assembly (B).
Align the three holes in the light kit pan (D)Make sure the notch in the light kit pan (D) Position the light kit pan (D) and re-install the three screws (VV) that were removed in the first step to secure the light kit pan (D).

Attaching the light kit fitter assembly and glass

CAUTION: To reduce the risk of electric shock, disconnect the electrical supply circuit to the fan before installing the light fixture.

WARNING: Allow the glass to cool completely before removing.

CAUTION: Make sure the power is off before attaching or removing the shatter resistant LED.

Connect white wire from fan to white wire from LED light kit and then connect blue wire from fan to black wire from LED light kit.(SS)
Secure the LED light kit(E) in the light kit pan (D).
Place the glass bowl (E) into the light kit pan (D) , aligning the three flat areas on the top flange of the glass bowl (E) with the three raised dimples in the light kit pan (D). Turn the glass bowl (E) clockwise until it stops.

Dual-Slide Ceiling Fan Wall-Mounted Control

IMPORTANT POINTS TO REMEMBER:
Read carefully before attempting to install this electrical device and retain the instruction for future reference.

Please note that all fixed wiring appliances should be installed by a qualified electrician.
To avoid possible electrical shock, be sure electricity is turned off at the main fuse box or circuit breaker panel before wiring.
Do not mount wall control near heat producing equipment.
Use of this control with some ceiling fans could result in fire, shock and serious personal injury. Use this speed control only with capacitor speed controlled ceiling fans.
Make certain no bare wires are exposed outside the connectors.
This unit is to be used for the control of ceiling fans at AC120V 60Hz power supply only.

INSTALLATION INTRUCTIONS

Disconnect the power and remove the existing wall plate and switch.

Set all knobs on the dual slide wall-mounted control in the OFF position.
Installation of this control requires that a three-conductor cable with ground wire be run between the control wall box and the ceiling fan outlet box. (Figure 1)
Make wire connections and secure with wire nuts supplied, refer to figure 2.
- Connect black wire from A.C. power supply to black wire from the wall-mounted control.
- Connect black or red wire from the ceiling fan to black wire from the wall-mounted control.
- Connect blue wire from the ceiling fan to blue wire the wall-mounted control.
Secure the wall-mounted control to the outlet box with two screws provided. (Figure 3)
Secure the face plate over the wall control with two screws provided.

NOTE
If your ceiling fan would be used with the original pull chain switch, please always have the fan switch set to high speed and the light switch set to on position before using the wall control. To avoid accidental pull chain use, shorten chain by cutting it 1” below switch body.

FUNCTION

Fan switch:

0: POWER OFF
H: HIGH SPEED
M: MEDIUM SPEED
L2: LOW SPEED
L1: L. LOW SPEED 9

Light Switch:

0: POWER OFF
When you push the knob upward slowly, the lightness of light will turn brighter and brighter.

Care and Cleaning

WARNING: Make sure the power is off before cleaning your fan.

Because of the fan’s natural movement, some connections may become loose. Check the support connections, brackets, and blade attachments twice a year. Make sure they are secure. It is not necessary to remove the fan from the ceiling.
Clean your fan periodically to help maintain its new appearance over the years. Do not use water when cleaning, as this could damage the motor, or the wood , or possibly cause an electrical shock. Use only a soft brush or Iint-free cloth to avoid scratching the finish. The plating is sealed with a lacquer to minimize discoloration or tarnishing.
You can apply a light coat of furniture polish to the wood for additional protection and enhanced beauty. Cover small scratches with a light application of shoe polish.
You do not need to oil your fan. The motor has permanently-lubricated sealed ball bearings.

Troubleshooting

Problem	Solution
The fan will not start.

Check the main and branch circuit fuses or breakers.
Chech the line wire connections to the fan and switch wire connections in teh switch housing.

The fan is noisy.|

Ensure all motor housing screws are snug.
Ensure the screws that attach the blade bracket to the motor hub are tight.
Ensure the wire nut connections are not rattling against each other or the interior wall of the switch housing.
Allow a 24-hour “breaking in” period. Most noises associated withe a new fan disappear during this time.
If you are using the Ceiling Fan light kit, ensure the screws securing the glassware are tight. Check that the light bulbs are also secure.
Ensure the canopy is a short distance from the ceiling.It shoulb not touch the ceiling.
Ensure your outlet box is secure and rubber isolator pads were used between the mounting plate and outlet box.

The fan wobbles.|

Check that all blade and blade arm screws are secure.
Most fan wobble problems are caused when blade levels are unequal. Check this level by selecting a point on the ceiling above the tip of one of the blades. Measure from a point on the center of the blade to the point on the ceiling. Rotate the fan until the next blade is positioned for measurement, and measure from the same point on each blade to the ceiling. Repeat for each blade. Any measurement deviation should be within 1/8 in. Run the fan for ten minutes. If the minutes. If the fan continues to wobble please contact Customer Service and a balancing kit will be sent to you at no charge.