RCF COMPACT C 32 Two Way Professional Speakers Owner’s Manual

RCF COMPACT C 32 Two Way Professional Speakers Owner’s Manual

SAFETY PRECAUTIONS AND GENERAL INFORMATION

The symbols used in this document give notice of important operating instructions and warnings which must be strictly followed.

| CAUTION| Important operating instructions: explains hazards that could damage a product, including data loss
---|---|---
| WARNING| Important advice concerning the use of dangerous voltages and the potential risk of electric shock, personal injury or death�
| IMPORTANT NOTES| Helpful and relevant information about the topic
| SUPPORTS, TROLLEYS AND CARTS| Information about the use of supports, trolleys and carts� Reminds to move with extreme caution and never tilt�
| WASTE DISPOSAL| This symbol indicates that this product should not be disposed with your household waste, according to the WEEE directive (2012/19/EU) and your national law�

IMPORTANT NOTES
This manual contains important information about the correct and safem use of the device. Before connecting and using this product, please read this instruction manual carefully and keep it on hand for future reference. The manual is to be considered an integral part of this product and must accompany it when it changes ownership as a reference for correct installation and use as well as for the safety precautions. RCF S.p.A. will not assume any responsibility for the incorrect installation and / or use of this product.

SAFETY PRECAUTIONS

1. All the precautions, in particular the safety ones, must be read with special attention, as they provide important information.

2. Power supply from mains
   a. The mains voltage is sufficiently high to involve a risk of electrocution; install and connect this product before plugging it in.
   b. Before powering up, make sure that all the connections have been made correctly and the voltage of your mains corresponds to the voltage shown on the rating plate on the unit, if not, please contact your RCF dealer.
   c. The metallic parts of the unit are earthed through the power cable. An apparatus with CLASS I construction shall be connected to a mains socket outlet with a protective earthing connection.
   d. Protect the power cable from damage; make sure it is positioned in a way that it cannot be stepped on or crushed by objects.
   e. To prevent the risk of electric shock, never open this product: there are no parts inside that the user needs to access.
   f. Be careful: in the case of a product supplied by manufacturer only with POWERCON connectors and without a power cord, jointly to POWERCON connectors type NAC3FCA (power-in) and NAC3FCB (power-out), the following power cords compliant to national standard shall be used:

   • EU: cord type H05VV-F 3G 3×2.5 mm2 – Standard IEC 60227-1
   • JP: cord type VCTF 3×2 mm2; 15Amp/120V~ – Standard JIS C3306
   • US: cord type SJT/SJTO 3×14 AWG; 15Amp/125V~ – Standard ANSI/UL 62

3.  Make sure that no objects or liquids can get into this product, as this may cause a short circuit. This apparatus shall not be exposed to dripping or splashing. No objects filled with liquid, such as vases, shall be placed on this apparatus. No naked sources (such as lighted candles) should be placed on this apparatus.

4.  Never attempt to carry out any operations, modifications or repairs that are not expressly described in this manual. Contact your authorized service centre or qualified personnel should any of the following occur:

   • The product does not function (or functions in an anomalous way).
   • The power cable has been damaged.
   • Objects or liquids have got in the unit.
   • The product has been subject to a heavy impact.

5. If this product is not used for a long period, disconnect the power cable.

6.  If this product begins emitting any strange odours or smoke, switch it off immediately and disconnect the power cable.

7. Do not connect this product to any equipment or accessories not foreseen. For suspended installation, only use the dedicated anchoring points and do not try to hang this product by using elements that are unsuitable or not specific for this purpose. Also check the suitability of the support surface to which the product  is anchored (wall, ceiling, structure, etc.), and the components used for attachment (screw anchors, screws, brackets not supplied by RCF etc.), which must guarantee the security  f the system / installation over time, also considering, for example, the mechanical vibrations normally generated by transducers. To prevent the risk of falling equipment, do not stack multiple units of this product unless this possibility is specified in the user manual.

8. RCF S.p.A. strongly recommends this product is only installed by
   professional qualified installers (or specialised firms) who can ensure correct installation and certify it according to the regulations in force. The entire audio system must comply with the current standards and regulations regarding electrical systems.

9. Supports, trolleys and carts
   The equipment should be only used on supports, trolleys and carts, where necessary, that are recommended by the manufacturer. The equipment / support / trolley / cart assembly must be moved with extreme caution. Sudden stops, excessive pushing force and uneven floors may cause the assembly to overturn. Never tilt the assembly.

10. There are numerous mechanical and electrical factors to be considered when installing a professional audio system (in addition to those which are strictly acoustic, such as sound pressure, angles of coverage, frequency response, etc.).

11. Hearing loss.
    Exposure to high sound levels can cause permanent hearing loss. The acoustic pressure level that leads to hearing loss is different from person to person and depends on the duration of exposure. To prevent potentially dangerous exposure to high levels of acoustic pressure, anyone who is exposed to these levels should use adequate protection devices. When a transducer capable of producing high sound levels is being used, it is therefore necessary to wear ear plugs or protective earphones. See the manual technical specifications to know the maximum sound pressure level.

OPERATING PRECAUTIONS

• Place this product far from any heat sources and always ensure an adequate air circulation around it.
• Do not overload this product for a long time.
• Never force the control elements (keys, knobs, etc.).
• Do not use solvents, alcohol, benzene or other volatile substances for cleaning the external parts of this product.

IMPORTANT NOTES

To prevent the occurrence of noise on line signal cables, use screened cables only
and avoid putting them close to:

• Equipment that produces high-intensity electromagnetic fields
• Power cables
• Loudspeaker lines

WARNING! CAUTION! To prevent the risk of fire or electric shock, never expose this product to rain or humidity.

WARNING! To prevent electric shock hazard, do not connect to mains power supply while grille is removed

WARNING! to reduce the risk of electric shock, do not disassemble this product unless you are qualified. Refer servicing to qualified service personnel.

CORRECT DISPOSAL OF THIS PRODUCT

This product should be handed over to an authorized collection site for recycling waste electrical and electronic equipment (EEE).
Improper handling of this type of waste could have a possible negative impact on the environment and human health due topotentially hazardous substances that are generally associated with EEE. At the same time, your cooperation in the correct disposal of thisproduct will contribute to the effective usage of natural resources. For more information about where you can drop off your waste equipment for recycling, please contact your local city office, waste authority or your household waste disposal service.

CARE AND MAINTENANCE

To ensure a long-life service, this product should be used following these advices:

• if the product is intended to be set up outdoors, be sure it is under cover and protected to rain and moisture.
• If the product needs to be used in a cold environment, slowly warm up the voice coils by sending a low-level signal for about 15 minutes before sending high-power signals.
• Always use a dry cloth to clean the exterior surfaces of the speaker and always do it when the power is turned off.

CAUTION: to avoid damaging the exterior finishes do not use cleaning solvents or abrasives.

WARNING! CAUTION! For powered speakers, do cleaning only when the power is turned off.

RCF S.p.A. reserves the right to make changes without prior notice to rectify any errors and / or omissions. Always refer to the latest version of the manual on www.rcf.it.

DESCRIPTION

COMPACT C SERIES

COMPACT C is a series of professional two-way fullrange speakers, suitable for a wide range of medium throw applications, even if their balanced sound is a big asset also in nearfield applications. Thanks to the use of top quality neodymium transducers and 100° x 50° constant directivity horn, COMPACT C speakers feature high sensitivity and exceptional sound quality, with smooth and wide frequency response. The incredible, distortion free, SPL level they can provide goes far beyond expectations of such a compact solution. The elegant design with accurate finishing makes COMPACT C speakers suitable for any environment, while optional mounting accessories allow using it for wall or ceiling installation

C 32
12’’ neodimium woofer, 3.0’’ v.c. 1.4’’ neodimium compression driver, 3.0’’ v.c. Directivity H 100° x V 50°

C 45
15’’ neodimium woofer, 4.0’’ v.c. 1.4’’ neodimium compression driver, 4.0’’ v.c. Directivity H 100° x V 50°

CONNECTIONS

The rear panel displays 2 sockets, both for ‘Neutrik Speakon NL4’ (4-pole) plugs:
One of the two sockets receives the signal from the amplifier; the other one becomes the “THROUGH” socket and be used to link another speaker

WARNING! CAUTION! Loudspeaker connections should be only made by qualified and experienced personnel having the technical know-how or enough specific instructions (to ensure that connections are made correctly) in order to prevent any electrical danger.

To prevent any risk of electric shock, do not connect loudspeakers when the amplifier is switched on.

Before turning the system on, check all connections and make sure there are no accidental short circuits.

The entire sound system shall be designed and installed in compliance with the current local laws and regulations regarding electrical systems.

The entire sound system shall be designed and installed in compliance with the current local laws and regulations regarding electrical systems.

WARNING! CAUTION! Loudspeakers are to be install by qualified personnel, respecting all safety standards. Loudspeakers are to be installed securely.

Make sure the support structure (walls / ceilings) has the necessary mechanical characteristics for the loudspeaker weight, without the risk of a fall that could damage things or cause an injury.

Use attachments elements suitable for walls / ceilings (e.g. wall plugs for bricks, for concrete, etc.)

CONFIGURATIONS

Both Compact C32 and C 45 can be used either in vertical or horizontal configuration. When used in horizontal configuration, the horn needs to be rotated 9

VERTICAL CONFIGURATION

HORIZONTAL CONFIGURATION (horn rotated)

CONFIGURATIONS

HORN ROTATION

1. Remove the 4 screws from the top and bottom panel and remove the front grille
   

2. Remove the 8 screws from the horn and rotate it 90°
   

3. Screw back the horn and the grille. The speaker can now be used horizontally.

HORIZONTAL MOUNTING WITH U BRACKET

Accessories needed:

• H-BR 2X COMPACT M 12 (for COMPACT C 32);
• H-BR 2X COMPACT C 45 (for COMPACT C45);

1. Fix the U bracket to the wall / ceiling through at least 4 lateral wall plugs (max. M8) plus a central one (max. M10).
2.  Mount the U bracket to the loudspeaker by tightening the two M10x35 bolts into the holes of the loudspeaker top and bottom, as shown in the figure below
   

Alternatively, it’s possible to install the speaker in a less protruding way by using the other two inner holes on the U bracket. Before tightening the two M10 bolts, adjust the loudspeaker vertical tilt and then (when you found the right angle) fix it through two M4.2×22 self-threading screws (passing through the small hole of the U bracket) directly into the loudspeaker cabinet wood

NOTE: instead of simple M10 bolts, it is possible to use the M10 bolt included knobs.

CAUTION: do not tilt the loudspeaker upwards.

VERTICAL MOUNTING WITH U BRACKET

Accessories needed:

• V-BR 2X COMPACT M 12 (for COMPACT C 32);
  

• V-BR 2X COMPACT C 45 (for COMPACT C 45);

Fix the U bracket to the wall / ceiling through at least 4 lateral wall plugs (max. M8) plus a central one (max. M10).

1. After removing the screwes on the speaker sides, fix the angular adaptor on the speaker with the M8x45 screws.
2. Place the plastic cover on the angular adaptor.
3. Fix the braket to the speaker with the M10x30 screws placing a grower washer between the bracket and the plastic cover.

Set the speaker vertical tilt and fix the inclination by screwing the two M6 screws on the adaptor

NOTE: alternatively, a less protruding installation is possibile thanks to the inner holes of the U bracket.

CAUTION: do not tilt the loudspeaker upwards.

HN-KIT COMPACT C 32 C 45

With the use of the accessory HN-KIT COMPACT C 32 C 45, it is possibile to replace the speaker horn with two different horns and change directivity to 100° x 25° or 60° x 25°

Whether the speaker is used vertically or horizontally the waveguide must always be mounted as shown on the picture on the side.
**VERTICAL CONFIGURATION
![VERTICAL

CONFIGURATION](https://manuals.plus/wp- content/uploads/2023/01/Screenshot_16-197.png)**

HORIZONTAL CONFIGURATION (horn rotated)

NOTES ABOUT LOW IMPEDANCE CONNECTIONS

WARNING! CAUTION!

• The total loudspeaker impedance must not be lower than the amplifier output impedance. Note: a loudspeaker total impedance equal to the amplifier output one permits to get the maximum deliverable power (but an higher loudspeaker impedance entails less power).
• The total loudspeaker power shall be adequate for the maximum deliverable power of the amplifier.
• The loudspeaker line shall be short (for long distances, it may be necessary to use cables with large cross-section wires).
• Always use cables having wires with an adequate cross-section, considering the cable length and the total loudspeaker power.
• Loudspeaker lines must be kept separated from the mains cables, microphone cables or others, in order to avoid inductive phenomena may cause hum or noises.
• Use loudspeaker cables with twisted wires to reduce hum caused by inductive effects due to coupling with electromagnetic fields.
• Do NOT connect the low impedance input directly to 70 / 100 V constant voltage lines.

COMPACT C 32 DIMENSIONS / DIMENSIONI

COMPACT C 45 DIMENSIONS / DIMENSIONI

SPECIFICATIONS / DATI TECNICI

|

| COMPACT C 32| COMPACT C 45
---|---|---|---
Acoustical specifications| Frequency Response (-10dB): Max SPL @ 1m: Horizontal coverage angle: Vertical coverage angle: Directivity index Q: System Sensitivity:| 54 Hz ÷ 20000 Hz 137 dB
100°
50°
10
97 dB| 48 Hz ÷ 20000 Hz138 dB
100°
50°
10
98 dB
Power section| Amplification: Nominal Impedance: Power Handling: Peak Power Handling: Recommended Amplifier: Protections: Crossover Frequencies:| Full Range8 ohm
600 W RMS
2400 W PEAK 1200 W
Dynamic Active Mosfet
1100 Hz| Full Range8 ohm
700 W RMS
2800 W PEAK 1400 W
Dynamic Active Mosfet
1100 Hz
Transducers| Compression Driver: Woofer:| 1 x 1.4” neo, 3.0” v.c 12” neo, 3.5” v.c| 1 x 1.4” neo, 4.0” v.c 15” neo, 4.0” v.c
Input/Output section| Input connectors: Output connectors:| Speakon
Speakon| SpeakonSpeakon
Standard compliance| CE marking:| Yes| Yes
hysical specifications| Cabinet/Case
Material:Hardware:Grille: Color:| Birch plywood
4 x M8, 14 x M10
Steel with clothing Black| Birch plywood4 x M8, 14 x M10
Steel with clothing
Black
Size| Height:
Width:
Depth: Weight:| 620 mm / 24.41 inches 361.8 mm / 14.24 inches 404 mm /
15.91 inches 23.5 kg /
51.81 lbs| 705 mm / 27.76 inches 418.8 mm / 16.49 inches
460 mm / 18.11 inches32.5 kg / 71.65 lbs

References

• Audio Experience

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>