LEEDARSON

Bypass Door Window Sensor Z-Wave 700

SKU: 7AA-SS-VE-A0

Quickstart

This is a
secure
Alarm Sensor
for
.

Please make sure the internal battery is fully charged.

Important safety information

Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law.
The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material.
Use this equipment only for its intended purpose. Follow the disposal instructions.

Do not dispose of electronic equipment or batteries in a fire or near open heat sources.

What is Z-Wave?

Z-Wave is the international wireless protocol for communication in the Smart Home. This
device is suited for use in the region mentioned in the Quickstart section.

Z-Wave ensures a reliable communication by reconfirming every message ( two- way
communication) and every mains powered node can act as a repeater for other nodes
( meshed network ) in case the receiver is not in direct wireless range of the
transmitter.

This device and every other certified Z-Wave device can be used together with any other
certified Z-Wave device regardless of brand and origin as long as both are suited for the
same frequency range.

If a device supports secure communication it will communicate with other devices
secure as long as this device provides the same or a higher level of security.
Otherwise it will automatically turn into a lower level of security to maintain
backward compatibility.

For more information about Z-Wave technology, devices, white papers etc. please refer
to www.z-wave.info.

Product Description

The Leedarson door window sensor is designed for use with scenes in home automation and security systems, the door window sensor lets you know when door or windows is opened and can trigger different actions in response to that open action (or close action).

Prepare for Installation / Reset

Please read the user manual before installing the product.

In order to include (add) a Z-Wave device to a network it must be in factory default
state. Please make sure to reset the device into factory default. You can do this by
performing an Exclusion operation as described below in the manual. Every Z-Wave
controller is able to perform this operation however it is recommended to use the primary
controller of the previous network to make sure the very device is excluded properly
from this network.

Inclusion/Exclusion

On factory default the device does not belong to any Z-Wave network. The device needs
to be added to an existing wireless network to communicate with the devices of this network.
This process is called Inclusion.

Devices can also be removed from a network. This process is called Exclusion.
Both processes are initiated by the primary controller of the Z-Wave network. This
controller is turned into exclusion respective inclusion mode. Inclusion and Exclusion is
then performed doing a special manual action right on the device.

Quick trouble shooting

Here are a few hints for network installation if things dont work as expected.

1. Make sure a device is in factory reset state before including. In doubt exclude before include.
2. If inclusion still fails, check if both devices use the same frequency.
3. Remove all dead devices from associations. Otherwise you will see severe delays.
4. Never use sleeping battery devices without a central controller.
5. Dont poll FLIRS devices.
6. Make sure to have enough mains powered device to benefit from the meshing

Association – one device controls an other device

Z-Wave devices control other Z-Wave devices. The relationship between one device
controlling another device is called association. In order to control a different
device, the controlling device needs to maintain a list of devices that will receive
controlling commands. These lists are called association groups and they are always
related to certain events (e.g. button pressed, sensor triggers, …). In case
the event happens all devices stored in the respective association group will
receive the same wireless command wireless command, typically a ‘Basic Set’ Command.

Association Groups:

Group NumberMaximum NodesDescription

Configuration Parameters

Z-Wave products are supposed to work out of the box after inclusion, however
certain configuration can adapt the function better to user needs or unlock further
enhanced features.

IMPORTANT: Controllers may only allow configuring
signed values. In order to set values in the range 128 … 255 the value sent in
the application shall be the desired value minus 256. For example: To set a
parameter to 200 it may be needed to set a value of 200 minus 256 = minus 56.
In case of a two byte value the same logic applies: Values greater than 32768 may
needed to be given as negative values too.

Parameter 1: 7210Range

Set the range about magnetic field Range:0-the range of parameter 0x02 is 0x00000001-0x00004B00, the range of parameter 0x03 is 0x00000001-0x00002300.1- the range of parameter 0x02 is 0x00000001-0x0002EE00, the range of parameter 0x03 is 0x00000001-0x00015E00.
Size: 1 Byte, Default Value: 0

SettingDescription

0 – 1| 0-the range of parameter 0x02 is 0x00000001-0x00004B00 and the range of parameter 0x03 is 0x00000001-0x00002300. 1- the range of parameter 0x02 is 0x00000001-0x0002EE00 and the range of parameter 0x03 is 0x00000001-0x00015E00.
---|---

Parameter 10: LowBatPrecent

This parameter defines a battery level as the low battery.Range:0x05-0x32
Size: 1 Byte, Default Value: 10

SettingDescription

5 – 50| 0x0A defines the low battery level. 0x05 means that device will send a low level alarm report when the battery levle is less than 5%. 0x32 means that device will send a low level alarm report when the battery levle is less than 50%.
---|---

Parameter 14: BasicEnable

Enable/Disable BASIC SET command 0Disable.1Enable.
Size: 1 Byte, Default Value: 0

SettingDescription

0 – 1| parameter 14 will disable/enable the basic set command when it is triggered. the value 0 means that sensor will not send basic set command when the sensor is triggered, value 1 means that the sensor willl send basic set command when it is triggered.
---|---

Parameter 15: BasicReverse

Door Sensor reverse its value of BASIC SET when the magnet is triggered. 0 -Send BASIC SET VALUE = 0xFF/0x00 to nodes associated with group 2 when door is opened/closed.1 Send BASIC SET VALUE = 0/255 to nodes associated with group 2 when door is opened/closed.
Size: 1 Byte, Default Value: 0

SettingDescription

0 – 1| 0 -Send BASIC SET VALUE = 0xFF/0x00 to nodes associated with group 2 when door is opened/closed. 1 Send BASIC SET VALUE = 0/255 to nodes associated with group 2 when door is opened/closed.
---|---

Parameter 2: 7210OP

7210OPSet the average magnetic field in utRange: 0x00000001-0x00004B00or 0x00000001-0x0002EE00
Size: 4 Byte, Default Value: 640

SettingDescription

1 – 19200| the average magnetic field.0x00000001 means that the magnetic field is 1 ut, 0x0002EE00 means that the magnetic field is192000 ut
---|---

Parameter 20: Bypass

Enable/Disable Bypass mode 0Enable.1Disable.
Size: 1 Byte, Default Value: 1

SettingDescription

0 – 1| parameter 20 disable/enable the bypass mode. the value 0 means that sensor will enter a bypass mode when the bypass button is pressed, value 0 means that sensor will not enter bypass mode when the bypass button is pressed
---|---

Parameter 21: temp

The interval time the Door Sensor reports the Multilevel Sensor Report to association group1 in minutes.0x0F-0xFF
Size: 1 Byte, Default Value: 15

SettingDescription

15 – 127| parameter 0x21 assign the time the sensor send the temperature report to associated node in minute. For example0x10 means that sensor will send a temperature report every 14 mins
---|---

Parameter 254: LockConfig

Enable/Disable configuration set 0Enable.1Disable.
Size: 1 Byte, Default Value: 0

SettingDescription

0 – 1| parameter 0xFE disable/enable the configuration set function. value 0 means that any configuration set will be disabled, value 1 means that configuration set will be enbale,you can change the values of the configration parameters
---|---

Parameter 3: 7210PolHyst

Set the offset about magnetic field Range: 0x00000001-0x00002300or 0x00000001-0x00015E00
Size: 4 Byte, Default Value: 200

SettingDescription

1 – 8960| the offset of the magnetic field.0x00000001 means that the magnetic field is 1 ut, 0x0002EE00 means that the magnetic field is89600 ut
---|---

Technical Data

Supported Command Classes

• Association Grp Info V3
• Association V2
• Battery
• Central Scene V3
• Configuration V4
• Device Reset Locally
• Firmware Update Md V5
• Indicator V3
• Manufacturer Specific V2
• Multi Channel Association V4
• Notification V8
• Powerlevel
• Security
• Security 2
• Supervision
• Transport Service V2
• Version V3
• Wake Up V2
• Zwaveplus Info V2

Explanation of Z-Wave specific terms

• Controller — is a Z-Wave device with capabilities to manage the network.
  Controllers are typically Gateways,Remote Controls or battery operated wall controllers.

• Slave — is a Z-Wave device without capabilities to manage the network.
  Slaves can be sensors, actuators and even remote controls.

• Primary Controller — is the central organizer of the network. It must be
  a controller. There can be only one primary controller in a Z-Wave network.

• Inclusion — is the process of adding new Z-Wave devices into a network.

• Exclusion — is the process of removing Z-Wave devices from the network.

• Association — is a control relationship between a controlling device and
  a controlled device.

• Wakeup Notification — is a special wireless message issued by a Z-Wave
  device to announces that is able to communicate.

• Node Information Frame — is a special wireless message issued by a
  Z-Wave device to announce its capabilities and functions.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>