EZRide EZR Wheelchair Power Assist Instructions
- June 8, 2024
- EZRide
Table of Contents
EZRide EZR Wheelchair Power Assist
WARNING
MAX SPEED: 12mph
WEIGHT LIMIT: 300Ibs
FOR WHEELCHAIR USE ONLY. NOT A TOY.
CAUTION
NO SHARP TURNS AT MEDIUM OR HIGH SPEEDSI NOT FORUSE IN SAND LOW TO MEDIUM SPEE
IN ROUGH TERRAIN BATTERY MUST NOT8 CLOSE TO EXTREME HEAT OR COLD.
MAX 140F
MIN-4’F
WARNING
LIHON 36V 350 Wh 10.0AH
Battery/Pile/Bateria 130501002DGS
To reduce the risk of injury, user must read Operator’s Manual. Risk of fire
and burns. Do not expose battery to Rain, Water, or Liquids, Open, Crush, Heat
Above 140’F, Indnerate or Short Terminals. Follow Manufacturer’s Instructions.
Use only with charger listed i
Operators Manual.
Remove Battery from unit when storing for long periods of time, changing
attachments, or making adjustments.
Shield Innovations LLC
107 Pinckney St.
Oldsmar, FL 34677
888-987-4769
TOW BAR PARTS
CHAIR CLIP BREAKDOWN HITCH BREAKDOWN 
TOW BAR INSTALLATION
Chair Clip
Place chair clip around horizontal or vertical wheel chair bar. Close to front
of chair with screws facing outward.
Place chair clip cover over bar. Confirm it matches the curvature of the bar.
Screw small nut first until it meets the cover, do not tighten. Then place
second lock nut on screw. Do not tighten completely. Repeat on other side of
chair. Make sure left and right clip are in the same position on the bar.
Adjust clips to make as level as possible
Slide Tube Make sure the chair is in the expanded position. The tow bar is
spring loaded. Compress the slider tubes and line up with the chair clips.
Squeeze both the top and the bottom release buttons and push the slide tube
into the chair clip until the release buttons pop through the chair clip hole.
Do on both sides. Move the tow bar hitch until it is centered between the two
foot pads. Then tighten the 2 chair clips making sure the tow bar is level.
Tighten the 2 fastening knobs. It is normal for the tow bar to have some
slight movement.
TOW BAR UN-INSTALL Loosen both fastening knobs. With one hand squeeze the chair clip release buttons and pull the slide tube toward the center until it releases from the chair clip. Do the same on the other side. When both are released push both slide tubes to the center of the tow bar then remove from clips and tighten fastening knobs.
TOW BAR HITCH HEIGHT ADJUSTMENT
Normal position for EZ Ride tow bar hitch. Raise tow bar hitch to raise front
wheels of the chair higher off the ground. Lower tow bar hitch to lower front
wheels closer to the ground. 
KICKSTAND INSTALLATION
To install kick stand insert kick stand over the plate with the two screws.
Install two screw nuts and tighten with wrench. Make sure kick stand is
straight along back side of EZ Ride.
Kickstand 
HITCH HANDLE
& KICKSTAND INSTALLATION Position of the hitch handle assembly is NOT CORRECT.
CORRECT position for hitch handle, aligned even with white lines at top. If
adjustment needed, loosen Allen screws to move hitch handle assembly. Once
hitch handle is positioned, tighten using multi-tool. Align kickstand screw
inserts with white guide lines. Tighten with multi-tool.
EZRIDE-WHEELCHAIR CONNECTION While sitting in chair, using steering handle pull EZ ride towards tow bar hitch. Kickstand will automatically close. Line up EZ Ride handle inside hitch receiver so handle is inserted under receiver rod .
Pull EZ ride towards you and once handle is under rod push up to engage tow bar hitch. Once locked in confirm front wheels are off the ground by at least 2-3”. If not, adjust Towbar Hitch height. see page 6
EZRIDE-WHEELCHAIR RELEASE To release EZ ride from Tow Bar push up on steering handle and at the same time lift EZ Ride handle up. Holding on to EZ ride handle and steering bar Push down and forward to release EZ Ride from Tow Bar Hitch. Push EZ ride away from Chair to clear footrests. Pull kickstand away from EZ Ride to the extended position. Insure it is flush to the ground. Make sure EZ Ride is on level ground when extending Kickstand.
SPEEDOMETER & HANDLE CONTROLS
Display
functions:
Speed display, Battery level, Total mileage, Cumulative mileage, current speed
Short presses to change speed ECO
Throttle Controls
Speed 3 mph- this gear is designed to allow user to cruise alongside a person
walking as well as indoor use.
Note: Pressing throttle to start ECO speed has 3-second safety delay before
starting.
MID
Speed 6 mph- this gear is a moderate speed for outdoor use , do not make any
sharp turns.
HIGH
Speed 12 mph- CAUTION. This gear is fast . Use only on smooth surfaces in open
conditions. DO NOT MAKE ANY SHARP TURNS IN THIS SPEED.
How to set cruise control.
- Hold throttle on desired speed for 5 seconds. This will set the cruise control for that speed.
- To release cruise control apply brake or push throttle.
HANDLE FOLD INSTRUCTIONS
- To fold handle to down position grab round release ring and pull towards handle grip.
- Once release ring extended push handle to down position
- To adjust angle of Brake or Speedometer turn Allen screw counter clockwise to loosen. Adjust to position desired and tighten Allen screw
HANDLE BAR REVERSAL INSTRUCTIONS
- First, take off the front bracket by removing the four 4mm hex screws and rest the handle bars beside EZ-Ride.
- Then loosen the two screws that clamp the handle bar stem to the steering column using a 5mm hex key. Only loosen the stem until it is able to rotate.
- Rotate the stem 180 degrees and looking down from the top of the EZ-Ride and line up the stem with the drive wheel. Once both are lined up properly, tighten the stem down switching between the two screws so they are both tightened down evenly.
- Place the handle bars back on along with the bracket and start by hand tightening the four screws to get the threads started. Then tighten the screws in a pattern using the multitool so all screws will be tightened down evenly.
HOW TO CHARGE
Insert three
prong charging cable into port on top of EZ Ride.
Plug into normal 110 outlet.
Keep plugged in until light on charger turns green. Best to charge after each
use.
Note: Like a car EZ Ride will lose charge over time if not used on a
regular basis . Check battery before using EZ Ride
BATTERY CHARGER TRAVEL BAG
Battery
charger bag can be used for back of wheelchair mounting or clips can be joined
together for hanging or shoulder use.
Read Instruction Manual Completely Before Using EZ Ride
- DO NOT use medium or high speed indoors. Use eco speed only.
- DO NOT make a 360 degree turn using medium or high speed.
- DO NOT use EZ Ride on an incline of more than 30 degrees.
- DO NOT use high speed until you are comfortable with eco & medium speed.
- DO NOT use EZ Ride in sand or loose gravel.
More info at: www.buyezrideplus.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>