HAYLOU OW01 Bone Conducted Earphone User Manual

June 4, 2024
Haylou

HAYLIE OW01
User Manual

Overview

HAYLOU OW01 Bone Conducted Earphone

How to wear

When calling, adjust Mic towards the mouth to gain a better talking experience_

How to Charge

Prior to using please peel off the sticker covering the pogo pins and top up the earphones.

Stereo Mode Auto pairing: take out both EarBuds from the case and they will auto pair with each other in 2 or 3s. Earphones will be connectable to cellphones when the LED on either EarBud blinks white slowly. On your cellphone, search for HAYLOU OW01 and tap to connect. If earphones fail to be connected to a cellphone, please put the EarBuds back into the case and repeat the above steps. Earphones will auto-reconnect to the last device in connectivity records if any.
Note: earphones have been set to the factory when shipping out.

Manual pairing manually powers on two EarBuds and they will auto pair with each other when LED blinks white promptly. The LED on either EarBud will blink white slowly and now you can tap it on your cellphone to connect.
Bone-conducted earphone
Earbuds Parameters
Operation range: 10m(open space with no obstacle)
Model: Haylou OWO1
Charging time: approx. 1.5hr
Calling time: approx. 3hr
Standby time: approx. 105hr
Input: 5V ****430 mA
Battery type: Li-ion
Bluetooth version: V5. 2
Working temperature:-1050°C

Factory Setting
If earphones do not function well, please refer to the following steps to reset the factory: take earbuds out from the case. Power off the earphones then touch both panels for about 15s (LED will blink red and white three times twice). After that, put them back in the case. Delete connectivity record on the cellphone before processing another pairing (All connectivity records relating to the earbuds will all be removed).
Audio only outputs from a single earbud
It’s really rare. Please reset GT1 Pro, remove the connectivity record on your cellphone, and re-connect the earphones to your cellphone.
In other cases charging
LED glows solid white for 1 minute when earbuds are topped up.
The carry case cannot charge earbuds if its battery drains. LEDs on the carrying case will turn off once the case is topped up. If you charge it once again, LEDs will not give any notice, which does not mean the case is not charged.
Daily maintenance
Please do not shower with earbuds. Do not wear them on rainy days. Do not leave them in the washing machines or in other extreme situations. Clean them with a dry cloth after use in pursuing a longer service life.
FCC
FCC ID: 2ANIQ6-0W01
This device complies with part 15 of the FCC results. Operation is subject to the following two conditions:

  1. This device may not cause harmful interference and
  2. This device must accept any interference received, including interference that may cause undesired operation.

Note: This Equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the Federal Communications Commission (FCC) rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
1.1. Reorient or relocate the receiving antenna
1.2. Increase the separation between the equipment and receiver
1.3. Connect the equipment to an outlet on a circuit different from that to which the receiver is connected
1.4. Consult the dealer or an experienced radio/TV technician for help Changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment.

Aftersales & Support

Warranty Period:
12 months after purchase (please keep your receipt properly)
Free Service:
If any quality defects happen during the warranty period, please take the receipt and contact your distributor for aftersales service.
Following cases or any damages/defects that are not due to quality issues are not covered in the warranty.

  1. Any defects or damages caused by natural disasters, abnormal voltage, or other environmental facts.
  2. Any unauthorized disassembly, modification, or change of parts.
  3. Any damages caused by improper use of the product including soaking, corroding, falling down, squeezing, or exposure to abnormal temperature or humidity.

Model Number:

Date of Purchasing:
User’s Name:
User’s Phone:
User’s Address:
Shop’s Name:
Shop’s Address:
Comments:

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals