Aeotec

LED Bulb 6:Multi-Colour

SKU: ZWA002-A

Quickstart

This is a
secure
Light Dimmer
for
U.S. / Canada / Mexico.

To run this device please connect it to your mains power supply.

To add this device to your network execute the following action:
Add for inclusion 1.Ensure the led bulb has been excluded outside the network.2.Triggered by OFF ->ON (between 0.5-2 seconds each time)3.LED solid yellow Color (0xFFFF00) during the pairing(Timeout is 10 seconds).Failure:Blinks between 100% White and Red 0x0000FF color for 3 seconds (at a rate of 200ms per flash), Once 3 seconds have passed, the LED should return to a Warm White LED at 100%Success:Blinks between 100% White and Green 0x00FF00 color for 3 seconds (at a rate of 200ms per flash). Once 3 seconds have passed, the LED should return to a Warm White LED at 100%.

Please refer to the
Manufacturers Manual for more information.

Important safety information

Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law.
The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material.
Use this equipment only for its intended purpose. Follow the disposal instructions.

Do not dispose of electronic equipment or batteries in a fire or near open heat sources.

What is Z-Wave?

Z-Wave is the international wireless protocol for communication in the Smart Home. This
device is suited for use in the region mentioned in the Quickstart section.

Z-Wave ensures a reliable communication by reconfirming every message ( two- way
communication) and every mains powered node can act as a repeater for other nodes
( meshed network ) in case the receiver is not in direct wireless range of the
transmitter.

This device and every other certified Z-Wave device can be used together with any other
certified Z-Wave device regardless of brand and origin as long as both are suited for the
same frequency range.

If a device supports secure communication it will communicate with other devices
secure as long as this device provides the same or a higher level of security.
Otherwise it will automatically turn into a lower level of security to maintain
backward compatibility.

For more information about Z-Wave technology, devices, white papers etc. please refer
to www.z-wave.info.

Product Description

Standard form factor and appearance of the light bulb with 800 lm output RGBW: dimmable from 5% to 100%, tunable from 1800K to 6500K, and 16 million colors Possible to be included in groups, scenes, or schedules Suitable for indoor lighting: Corridors, Bedroom, Living Room, etc.

Prepare for Installation / Reset

Please read the user manual before installing the product.

In order to include (add) a Z-Wave device to a network it must be in factory default
state. Please make sure to reset the device into factory default. You can do this by
performing an Exclusion operation as described below in the manual. Every Z-Wave
controller is able to perform this operation however it is recommended to use the primary
controller of the previous network to make sure the very device is excluded properly
from this network.

Reset to factory default

This device also allows to be reset without any involvement of a Z-Wave controller. This
procedure should only be used when the primary controller is inoperable.

Reset the Device.1.Assuming led bulb was added to controller and was power on.2.RGBW bulb re-power 6 times (between 0.5-2 seconds each time).Note: ON -> OFF -> ON -> OFF -> ON -> OFF -> ON -> OFF -> ON -> OFF -> ON -> OFF -> ON 3.If the 6th power on, the led bulb change to Yellow color(into pairing process ), which means that the reset factory settings are successf.Using this action in case of the primary controller is missing or inoperable.

Safety Warning for Mains Powered Devices

ATTENTION: only authorized technicians under consideration of the country- specific
installation guidelines/norms may do works with mains power. Prior to the assembly of
the product, the voltage network has to be switched off and ensured against re-switching.

Inclusion/Exclusion

On factory default the device does not belong to any Z-Wave network. The device needs
to be added to an existing wireless network to communicate with the devices of this network.
This process is called Inclusion.

Devices can also be removed from a network. This process is called Exclusion.
Both processes are initiated by the primary controller of the Z-Wave network. This
controller is turned into exclusion respective inclusion mode. Inclusion and Exclusion is
then performed doing a special manual action right on the device.

Inclusion

Add for inclusion 1.Ensure the led bulb has been excluded outside the network.2.Triggered by OFF ->ON (between 0.5-2 seconds each time)3.LED solid yellow Color (0xFFFF00) during the pairing(Timeout is 10 seconds).Failure:Blinks between 100% White and Red 0x0000FF color for 3 seconds (at a rate of 200ms per flash), Once 3 seconds have passed, the LED should return to a Warm White LED at 100%Success:Blinks between 100% White and Green 0x00FF00 color for 3 seconds (at a rate of 200ms per flash). Once 3 seconds have passed, the LED should return to a Warm White LED at 100%.

Exclusion

Remove for exclusion 1.Assuming led bulb was added to controller.2.Triggered by OFF -> ON -> OFF -> ON -> OFF -> ON (between 0.5-2 seconds each time).3.LED Solid Purple/Violet Color (0xEE82EE) during the unpairing process. (Timeout is 10 seconds).Failure:Blinks between 100% White and Red 0x0000FF color for 3 seconds (at a rate of 200ms per flash), Once 3 seconds have passed, the LED should return to the last color ( memory status(color cc set)) of LED Bulb.Success:Blinks between 100% White and Blue 0x0000FF color for 3 seconds (at a rate of 200ms per flash). Once 3 seconds have passed, the LED should return to a Warm White LED at 100%.

Quick trouble shooting

Here are a few hints for network installation if things dont work as expected.

1. Make sure a device is in factory reset state before including. In doubt exclude before include.
2. If inclusion still fails, check if both devices use the same frequency.
3. Remove all dead devices from associations. Otherwise you will see severe delays.
4. Never use sleeping battery devices without a central controller.
5. Dont poll FLIRS devices.
6. Make sure to have enough mains powered device to benefit from the meshing

Association – one device controls an other device

Z-Wave devices control other Z-Wave devices. The relationship between one device
controlling another device is called association. In order to control a different
device, the controlling device needs to maintain a list of devices that will receive
controlling commands. These lists are called association groups and they are always
related to certain events (e.g. button pressed, sensor triggers, …). In case
the event happens all devices stored in the respective association group will
receive the same wireless command wireless command, typically a ‘Basic Set’ Command.

Association Groups:

Group NumberMaximum NodesDescription

1| 1| Set Configuration parameter 0x50 0: nothing.1: Send the Basic Report.2. Send Device Reset Locally CC
---|---|---

Configuration Parameters

Z-Wave products are supposed to work out of the box after inclusion, however
certain configuration can adapt the function better to user needs or unlock further
enhanced features.

IMPORTANT: Controllers may only allow configuring
signed values. In order to set values in the range 128 … 255 the value sent in
the application shall be the desired value minus 256. For example: To set a
parameter to 200 it may be needed to set a value of 200 minus 256 = minus 56.
In case of a two byte value the same logic applies: Values greater than 32768 may
needed to be given as negative values too.

Parameter 1: User custom mode for LED animations.

User custom mode for LED animations.0 = Disable custom mode.1= Blink Colors in order mode.2=Randomized blink color mode
Size: 1 Byte, Default Value: 0

SettingDescription

Parameter 16: Ramp rate when dimming using Multilevel Switch V1 CC in

100ms

Ramp rate when dimming using Multilevel Switch V1 CC in 100msValue range = 0x00 -0x64
Size: 1 Byte, Default Value: 20

SettingDescription

0 – 100| Specifying the ramp rate when dimming using Multilevel Switch V1 CC in 100ms
---|---

Parameter 2: Enable/Disable Strobe over Custom Color.

Enable/Disable Strobe over Custom Color.0 = Disable.1 = Enable.Others = Ignore.
Size: 1 Byte, Default Value: 0

SettingDescription

Parameter 3: Set the rate of change to next color in Custom Mode.

Set the rate of change to next color in Custom Mode.Value1 ~ Value4:Value Range = 5 – 8640000 (50 – 86400000ms)
Size: 1 Byte, Default Value: 50

SettingDescription

Parameter 4: Set color that LED Bulb blinks in (Blink Mode)

Set color that LED Bulb blinks in (Blink Mode)Value range =0x01-0xFF
Size: 1 Byte, Default Value: 1

SettingDescription

Parameter 80: Enable to send notifications to associated devices (Group

1. when the state of LED Bulb is changed.

Enable to send notifications to associated devices(Group 1) when the state of LED Bulb is changed.0 = Nothing.1= Basic CC report.
Size: 1 Byte, Default Value: 1

SettingDescription

changed

Parameter 81: The user can configure the parameter to adjust the color

component Warm White.

The user can configure the parameter to adjust the color component Warm White. Value range =Warm White(0x0A8C(2700k) ~ 0x1387 (4999k))
Size: 2 Byte, Default Value: 2700

SettingDescription

Parameter 82: The user can configure the parameter to adjust the color

component Cold White.

The user can configure the parameter to adjust the color component Cold White. Value rang = Cold White (0x1388 (5000k) ~ 0x1964 (6500k))
Size: 2 Byte, Default Value: 6500

SettingDescription

Technical Data

Supported Command Classes

• Association Grp Info
• Association V2
• Basic
• Configuration
• Device Reset Locally
• Firmware Update Md V2
• Manufacturer Specific V2
• Powerlevel
• Security
• Switch All
• Switch Color
• Switch Multilevel V2
• Version V2
• Zwaveplus Info V2

Explanation of Z-Wave specific terms

• Controller — is a Z-Wave device with capabilities to manage the network.
  Controllers are typically Gateways,Remote Controls or battery operated wall controllers.

• Slave — is a Z-Wave device without capabilities to manage the network.
  Slaves can be sensors, actuators and even remote controls.

• Primary Controller — is the central organizer of the network. It must be
  a controller. There can be only one primary controller in a Z-Wave network.

• Inclusion — is the process of adding new Z-Wave devices into a network.

• Exclusion — is the process of removing Z-Wave devices from the network.

• Association — is a control relationship between a controlling device and
  a controlled device.

• Wakeup Notification — is a special wireless message issued by a Z-Wave
  device to announces that is able to communicate.

• Node Information Frame — is a special wireless message issued by a
  Z-Wave device to announce its capabilities and functions.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>