HILTI TE 2000-AVR Cordless Demolition Hammers User Manual
- June 8, 2024
- HILTI
Table of Contents
- 1 Information about the operating instructions
- 2 Safety
- 3 Description
- 4 Technical data
- 5 Operation
- 6 Optional transport trolley
- 7 Care and maintenance
- 8 Troubleshooting
- 9 Disposal
- 10 RoHS (Restriction of Hazardous Substances)
- 11 Manufacturer’s warranty
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
HILTI TE 2000-AVR Cordless Demolition Hammers User Manual
Original operating instructions
1 Information about the operating instructions
1.1 About these operating instructions
- Read these operating instructions before the product is used or operated for the first time. This is a prerequisite for safe, trouble-free handling and use of the product.
- Observe the safety instructions and warnings in these operating instructions and on the product.
- Always keep the operating instructions with the product and make sure that the product is accompanied by these operating instructions only, when the product is given to other persons.
1.2 Explanation of symbols used
1.2.1 Warnings
Warnings alert persons to hazards that occur when handling or using the product. The following signal words are used:
⚠ DANGER
DANGER ! Draws attention to imminent danger that will lead to serious personal
injury or fatality.
⚠ WARNING
WARNING ! Draws attention to a potential threat of danger that can lead to
serious injury or fatality.
⚠ CAUTION
CAUTION ! Draws attention to a potentially dangerous situation that could lead
to personal injury or damage to the equipment or other property.
1.2.2 Symbols in the documentation
The following symbols are used in this document:
1.2.3 Symbols in the illustrations
The following symbols are used in illustrations:
1.3 Product-dependent symbols
1.3.1 Symbols on the product
The following symbols are used on the product:
1.4 Product information
products are designed for professional users and only trained, authorized personnel are permitted to operate, service and maintain the products. This personnel must be specifically informed about the possible hazards. The product and its ancillary equipment can present hazards if used incorrectly by untrained personnel or if used not in accordance with the intended use.
The type designation and serial number are printed on the rating plate.
Write down the serial number in the table below. You will be required to state
the product details when contacting Hilti Service or your local Hilti
organization to inquire about the product.
Product information
1.5 Declaration of conformity
We declare, on our sole responsibility, that the product described here complies with the applicable directives and standards. A copy of the declaration of conformity can be found at the end of this documentation. The technical documentation is filed here: Hilti Entwicklungsgesellschaft mbH | Tool Certification | Hiltistrasse 6 | 86916 Kaufering, Germany
2 Safety
2.1 General power tool safety warnings
WARNING
Read all safety warnings and all instructions. Failure to follow the warnings
and instructions may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
Work area safety
▶ Keep work area clean and well lit. Cluttered or dark areas invite accidents.
▶ Do not operate power tools in explosive atmospheres, such as in the presence
of flammable liquids, gases or dust. Power tools create sparks which may
ignite the dust or fumes.
▶ Keep children and bystanders away while operating a power tool. Distractions
can cause you to lose control.
Electrical safety
▶ Power tool plugs must match the outlet. Never modify the plug in any way. Do
not use any adapter plugs with earthed (grounded) power tools. Unmodified
plugs and matching outlets will reduce risk of electric shock.
▶ Avoid body contact with earthed or grounded surfaces, such as pipes,
radiators, ranges and refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
▶ Do not expose power tools to rain or wet conditions. Water entering a power
tool will increase the risk of electric shock.
▶ Do not abuse the cord. Never use the cord for carrying, pulling or
unplugging the power tool. Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords increase the risk of electric shock.
▶ When operating a power tool outdoors, use an extension cord suitable for
outdoor use. Use of a cord suitable for outdoor use reduces the risk of
electric shock.
▶ If operating a power tool in a damp location is unavoidable, use a residual
current device (RCD) protected supply. Use of an RCD reduces the risk of
electric shock.
Personal safety
▶ Stay alert, watch what you are doing and use common sense when operating a
power tool. Do not use a power tool while you are tired or under the influence
of drugs, alcohol or medication. A moment of inattention while operating power
tools may result in serious personal injury.
▶ Use personal protective equipment. Always wear eye protection. Protective
equipment such as dust mask, non-skid safety shoes, hard hat, or hearing
protection used for appropriate conditions will reduce personal injuries.
▶ Prevent unintentional starting. Ensure the switch is in the off‐position
before connecting to power source, picking up or carrying the tool. Carrying
power tools with your finger on the switch or energising power tools that have
the switch on invites accidents.
▶ Remove any adjusting key or wrench before turning the power tool on. A
wrench or a key left attached to a rotating part of the power tool may result
in personal injury.
▶ Do not overreach. Keep proper footing and balance at all times. This enables
better control of the power tool in unexpected situations.
▶ Dress properly. Do not wear loose clothing or jewellery. Keep your hair,
clothing and gloves away from moving parts. Loose clothes, jewellery or long
hair can be caught in moving parts.
▶ If devices are provided for the connection of dust extraction and collection
facilities, ensure these are connected and properly used. Use of dust
collection can reduce dust-related hazards.
Power tool use and care
▶ Do not force the power tool. Use the correct power tool for your
application. The correct power tool will do the job better and safer at the
rate for which it was designed.
▶ Do not use the power tool if the switch does not turn it on and off. Any
power tool that cannot be controlled with the switch is dangerous and must be
repaired.
▶ Disconnect the plug from the power source from the power tool before making
any adjustments, changing accessories, or storing power tools. Such preventive
safety measures reduce the risk of starting the power tool accidentally.
▶ Store idle power tools out of the reach of children and do not allow persons
unfamiliar with the power tool or these instructions to operate the power
tool. Power tools are dangerous in the hands of untrained users.
▶ Maintain power tools. Check for misalignment or binding of moving parts,
breakage of parts and any other condition that may affect the power tool’s
operation. If damaged, have the power tool repaired before use. Many accidents
are caused by poorly maintained power tools.
▶ Keep cutting tools sharp and clean. Properly maintained cutting tools with
sharp cutting edges are less likely to bind and are easier to control.
▶ Use the power tool, accessories and tool bits etc. in accordance with these
instructions, taking into account the working conditions and the work to be
performed. Use of the power tool for operations different from those intended
could result in a hazardous situation.
Service
▶ Have your power tool serviced by a qualified repair person using only
identical replacement parts.
This will ensure that the safety of the power tool is maintained.
2.2 Hammer safety warnings
▶ Wear ear protectors. Exposure to noise can cause hearing loss.
▶ Use auxiliary handles, if supplied with the tool. Loss of control can cause
personal injury.
▶ Hold power tool by insulated gripping surfaces, when performing an operation
where the cutting accessory may contact hidden wiring or its own cord. Cutting
accessory contacting a “live” wire may make exposed metal parts of the power
tool “live” and could give the operator an electric shock.
2.3 Additional safety instructions for breakers
Personal safety
▶ Use the product and accessories only when they are in perfect working order.
▶ Never tamper with or modify the product or accessories in any way.
▶ When chiseling into ceilings, walls and floors, always make sure that you
have a safe and firm stance. A sudden break-through can affect your balance!
▶ Apply appropriate safety measures at the opposite side of the workpiece in
work that involves breaking through. Parts breaking away could fall out and /
or fall down causing injury to other persons.
▶ You and the other persons in the vicinity must wear suitable eye protection,
a hard hat, ear protection, protective gloves and light respiratory protection
while the product is in use.
▶ Wear protective gloves when changing the accessory tool. Touching the
accessory tool can result in cuts and burns.
▶ Wear eye protection. Flying fragments can injure the body and eyes.
▶ Dust produced by grinding, sanding, cutting and drilling can contain
dangerous chemicals. Some examples are: lead or lead-based paints; brick,
concrete and other masonry products, natural stone and other products
containing silicates; certain types of wood, such as oak, beech and chemically
treated wood; asbestos or materials that contain asbestos. Determine the
exposure of the operator and bystanders by means of the hazard classification
of the materials to be worked. Implement the necessary measures to restrict
exposure to a safe level, for example by the use of a dust collection system
or by the wearing of suitable respiratory protection. The general measures for
reducing exposure include:
▶ working in an area that is well ventilated,
▶ avoidance of prolonged contact with dust,
▶ directing dust away from the face and body,
▶ wearing protective clothing and washing exposed areas of the skin with water
and soap.
▶ Take frequent breaks and do physical exercises to improve the blood
circulation in your fingers. High vibration during long periods of work can
lead to disorders of the blood vessels and nervous system in the fingers,
hands and wrists.
Electrical safety
▶ Before beginning work, check the working area for concealed electric cables
or gas and water pipes.
External metal parts of the product could give you an electric shock or cause
an explosion if you accidentally damage an electric cable or a gas or water
pipe.
Power tool use and care
▶ Wait until the product has come to a complete stop before you lay it down.
3 Description
3.1 Overview of the TE 2000-AVR 1
- Grip
- On/off switch
- Carrying handle
- Service indicator
- Air vents
- Chuck
3.2 Overview of the transport trolley 2
- Grip
- Locking bar
- Holder for accessory tools
- chisels
- Wheels & Wheel securing parts (washer, retaining pin)
- Power tool locating pin
3.3 Intended use
The product described is a hand-held electric breaker. It is designed for chiseling work on concrete, masonry and asphalt. It can also be used for excavating and compacting. The tool may be operated only when connected to a power supply providing a voltage and frequency in compliance with the information given on its rating plate.
3.4 Foreseeable misuse
- The power tool may be used only in a dry environment.
- Do not use the power tool where there is a risk of fire and explosion.
- Working with materials hazardous to health (e.g. asbestos) is not permissible.
3.5 Active Vibration Reduction
The tool is equipped with an Active Vibration Reduction (AVR) system which reduces vibration noticeably.
3.6 Service indicator
The breaker is equipped with a service indicator LED.
3.7 Items supplied
Electric breaker, operating instructions, grease. The transport trolley is available as an accessory. You can find other system products approved for your product at your local Hilti Center or online at: www.hilti.group
4 Technical data
4.1 Breaker
ℹ For details of the rated voltage, current, frequency and/or input power, please refer to the power tool’s country-specific type identification plate.
When powered by a generator or transformer, the generator or transformer’s power output must be at least twice the rated input power shown on the rating plate of the power tool. The operating voltage of the transformer or generator must always be within +5% and -15% of the rated voltage of the power tool.
Weight in accordance with EPTA procedure 01 14.5 kg
Impact speed 30 Hz
Protection class II
4.2 Noise information and vibration values in accordance with EN 60745
The sound pressure and vibration values given in these instructions were measured in accordance with a standardized test and can be used to compare one power tool with another. They can also be used for a preliminary assessment of exposure. The data given represents the main applications of the power tool. However, if the power tool is used for different applications, with different accessory tools, or is poorly maintained, the data can vary. This can significantly increase exposure over the total working period. An accurate estimation of exposure should also take into account the times when the tool is switched off, or when it is running but not actually being used for a job. This can significantly reduce exposure over the total working period. Identify additional safety measures to protect the operator from the effects of noise and/or vibration, for example: Maintaining the power tool and accessory tools, keeping the hands warm, organization of work patterns.
Noise emission values
5 Operation
5.1 Preparations at the workplace
⚠ CAUTION Risk of injury! Inadvertent starting of the product. Unplug the supply cord before making adjustments to the power tool or before changing accessories.
Observe the safety instructions and warnings in this documentation and on the product.
5.1.1 Fitting the accessory tool 3
-
Unplug the supply cord from the power outlet.
-
Lightly grease the connection end of the accessory tool.
Use only the recommended grease supplied by Hilti. Using the wrong grease can result in damage to the tool. -
Push the accessory tool into the chuck as far as it will go, turning it and applying light pressure until it engages with an audible click.
-
Check that the chisel has engaged correctly by gripping and pulling it.
5.1.2 Removing the accessory tool 4
⚠ CAUTION
Risk of injury! The accessory tool may be hot and/or have sharp edges.
▶Wear protective gloves when changing the accessory tool.
▶Never lay down a hot accessory tool on a flammable surface.
- Unplug the supply cord from the power outlet.
- Pull the tool lock back as far as it will go.
- Remove the accessory tool.
5.2 Types of work
⚠ WARNING Risk of electric shock! Severe injury and burns can result if any
attempt is made to operate the tool without an earth/ground conductor and
ground fault circuit interrupter correctly connected.
▶ Irrespective of whether mains power or generator power is used, always make
sure that an earth/ground conductor and ground fault circuit interrupter are
present in the power supply and that these are correctly connected.
▶ Do not use the product unless these safety measures are in place and fully
operational.
⚠ WARNING
A damaged supply cord presents a hazard! Do not touch the supply cord or
extension cord if damaged while working. Disconnect the supply cord plug from
the power outlet.
▶ Check the appliance’s supply cord at regular intervals and have it replaced
by a qualified specialist if found to be damaged.
Full approval must be obtained from the site engineer or architect prior to beginning the work.
5.2.1 Chiseling
- Plug the supply cord into the power outlet.
- Position the tip of the chisel at the desired location.
- Press the on/off switch.
ℹ Working at low temperatures: The hammering mechanism works only when the power tool has reached a minimum operating temperature. Bring the chisel into contact with the workpiece and allow the power tool to run under no load until the required temperature is reached. If necessary, repeat this procedure until the hammering mechanism begins to operate.
5.2.2 Switching off
- Press the on/off switch.
- Unplug the supply cord from the power outlet.
5.2.3 Working with the power tool 5
ℹ The chisel can be adjusted to 6 different positions (in 60° increments). This ensures that flat chisels and shaped chisels can always be set to the optimum working position.
▶ Bring the chisel into contact with the workpiece about 80 -100 mm (3¹⁄₈” –
4″) from its edge.
▶ When working close to reinforcing bars, always guide the tip of the chisel
toward the edge of the workpiece, not toward a reinforcing bar.
▶ Begin with the chisel positioned at an angle of 70° to 80° to the concrete
surface, with the tip of the chisel pointing toward the edge of the workpiece.
Break material away by subsequently increasing the angle to approx. 90° as the
chisel penetrates.
▶ Rotate the chisel regularly to help ensure even wear and to promote the
self-sharpening process.
▶ If inadequate pressure is applied, the chisel will jump around
uncontrollably. Application of excessive pressure will result in a loss of
chiseling performance.
6 Optional transport trolley
6.1 Transport
The transport trolley helps to ensure that the breaker can be transported safely.
- Take care to ensure that the transport trolley stands in a steady, secure position.
- Place the power tool on the locating pin provided on the transport trolley and always secure it for transport by closing the retaining bar.
- Push the chisels into the holders provided until they engage securely.
- Take care to use only safe transport routes.
- Do not park the transport trolley on an incline.
7 Care and maintenance
⚠ WARNING
Electric shock hazard! Attempting care and maintenance with the supply cord
connected to a power outlet can lead to severe injury and burns. Always unplug
the supply cord before carrying out care and maintenance tasks.
Care
- Carefully remove stubborn dirt from the tool.
- Clean the air vents carefully with a dry brush.
- Use only a slightly damp cloth to clean the casing. Do not use cleaning agents containing silicone as they can attack the plastic parts.
Maintenance
⚠ WARNING Danger of electric shock! Improper repairs to electrical
components may lead to serious injuries including burns.
▶ Repairs to the electrical section of the tool or appliance may be carried
out only by trained electrical specialists.
- Check all visible parts and controls for signs of damage at regular intervals and make sure that they all function correctly.
- Do not operate the product if signs of damage are found or if parts malfunction. Have it repaired immediately by Hilti Service.
- After cleaning and maintenance, fit all guards or protective devices and check that they function correctly.
ℹ To help ensure safe and reliable operation, use only genuine Hilti spare parts and consumables. Spare parts, consumables and accessories approved by Hilti for use with the product can be found at your local Hilti Store or online at: www.hilti.group.
8 Troubleshooting
If the trouble you are experiencing is not listed in this table or you are unable to remedy the problem by yourself, please contact Hilti Service.
8.1 Troubleshooting table
9 Disposal
♻ Most of the materials from which Hilti tools and appliances are manufactured can be recycled. The materials must be correctly separated before they can be recycled. In many countries, your old tools, machines or appliances can be returned to Hilti for recycling. Ask Hilti Service or your Hilti representative for further information.
Do not dispose of power tools, electronic equipment or batteries as household waste!
10 RoHS (Restriction of Hazardous Substances)
Click on the link to go to the table of hazardous substances: qr.hilti.com/r6025050. There is a link to the RoHS table, in the form of a QR code, at the end of this document.
11 Manufacturer’s warranty
▶ Please contact your local Hilti representative if you have questions about the warranty conditions.
Hilti Corporation
LI-9494 Schaan
Tel.: +423 234 21 11
Fax: +423 234 29 65
www.hilti.group
Hilti = registered trademark of Hilti Corp., Schaan Pos. 01 | 20221110
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>