OJ Electronics ETR2 Ice and Snow Melting User Manual
- June 8, 2024
- OJ Electronics
Table of Contents
MMNUAL
Type ETR2
Ice and snow melting
Introduction
Type ETR2 is an electronic thermostat for fully automatic, economical control of ice and snow melting systems on small outdoor areas and in gutters . Ice forms due to a combination of low temperature and moisture . ETR2 monitors both temperature and moisture, and the heating system is only activated if a possibility of snow or ice is indicated . ETR2 is suitable for controlling electric heating cables .
Glossary
TEMP SET For setting the temperature at which heating should be activated .
TIME SET For setting the afterheat duration . The length of time the system
should continue to provide heat after the moisture/temperature signals have
been eliminated by a heating cycle .
CONSTANT Allows heat to be provided constantly, independently of temperature
and moisture .
Startup
- Connect a power supply and the LED will light green .
- Adjust TEMP SET to the temperature at which ice and snow detection should be activated . Recommended initial setting: +3°C .
- Adjust TIME SET to the required afterheat duration (0-5 hours) . Recommended initial setting: 2 hours .
- The thermostat is now set up and will begin melting ice and snow when necessary .
Mode of operation/operating instructions
ETR2 activates the heating system if the outdoor temperature falls below the
temperature setpoint (TEMP SET) and the moisture sensor simultaneously detects
moisture .
When the outdoor temperature is below the temperature setpoint, the TEMP LED
will light red .
When the moisture sensor detects moisture, the MOIST LED will light red .
When both preconditions (low temperature and moisture) are met, the thermostat
will activate the ice and snow melting system, and the RELAY LED will light
red . After the moisture/temperature signals have been eliminated by a heating
cycle, heat will continue to be provided for the specified length of time, to
ensure that all ice and snow is completely melted .
If some ice and snow remains after the heating system has been deactivated,
the afterheat duration should be increased slightly by adjusting TIME SET .
The longer the afterheat duration, the more effective and less economical the
system will be .
If ice and snow is present on the heated area, but the TEMP LED is not lit,
the temperature setpoint (TEMP SET) should be increased to the point where the
TEMP LED lights red . The higher the temperature setpoint, the more effective
and less economical the system will be .
Constant heat On
In order to force ice and snow melting ON in any condition, it is possible to turn on the output relay, by turnng the TIME SET knob to Constant . The ON led flashes as long as Constant is activated . Be aware to adjust TIME SET back at the desired afterrun time, after all snow and ice has melted, to save energy .
Note that the CONSTANT HEAT ON setting will result in high energy consumption/costs .
Light indicator overview
| • ON | The power is on / Constant heat on (flashing) |
|---|---|
| • TEMP | Sensor temperature is below TEMP SET |
| • MOIST | Moisture/snow has been detected by sensor |
| • RELAY | Output RELAY ON / HEAT ON |
Fault codes
If faults occur, the thermostat disables all outputs and ceases to operate
until the fault has been remedied .
TEMP LED flashes red: Temperature sensor (ETOG / ETF) has been disconnected or
short-circuited .
MOIST LED flashes red: Moisture sensor in sensor (ETOG / ETOR) has been short-
circuited .
RELAY LED flashes red: Heating element in sensor (ETOG / ETOR) has been short-
circuited .
OJ cannot be held liable for any errors in catalogues, brochures or other
printed material . OJ reserves the right to alter its products without notice
. This also applies to products already on order, provided that such
alterations can be made without requiring subsequent changes in specifications
already agreed . All trademarks in this material are the property of the
respective companies . OJ and the OJ logotype are trademarks of OJ Electronics
A/S . All rights reserved .
OJ Electronics A/S
Stenager 13B · DK-6400 Sønderborg
Tel .: +45 73 12 13 14
Fax: +45 73 12 13 13
oj@ojelectronics.com ·
www.ojelectronics.com © 2020 OJ Electronics
A/S · ® The OJ trademark is a registred trademark belonging to OJ Electronics
A/S
57654D 06/20 (BCH)
© 2020 OJ Electronics A/S stranavejyen 42 • saksilad • os0Q Odaer
86 62 63 64 • www.automatikcentret.dk
info@automatikcentret.dk
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>