UTG Leapers OP-RMR20R Hunting Shooting Sporting Goods and Security Gear User Manual
- June 4, 2024
- UTG Leapers
Table of Contents
UTG Leapers OP-RMR20R Hunting Shooting Sporting Goods and Security Gear
SPECIFICATIONS
- Lens …………………………………………………………………………………………………. 0.89″ X 0.68″
- Reticle/ Illumination ……………………………………………………………………………. Red 4 MOA Dot
- Illumination Mode…………………………………………………………………………………………. Manual
- Adjustments ……………………………………………………………………………………… 1 MOA Per Click
- Build Material…………………………………………………………………………………. Anodized AL6061
- Battery Type ………………………………………………………………………………………….. CR2032 3V
- Battery Life ………………………………………………………………………………………… 55,000+ hrs
- Mount Footprint……………………………………………………………………………………………. RMR”
- LengthxWidth ……………………………………………………………………………………. 1.78″X1.14″
- Weight lw/Batteryl ………………………………………………………………………………………….. 1.102
BATTERY INSTALLATION
With its + side facing outward, insert the CR2032 battery into the battery compartment by first easing down one side of the battery against the metallic contact. Seat the remainder of the battery until flush. Test for function by holding the battery in place with your finger and applying a single press to the left side activation button. The MROS should turn on. Press and hold down the activation button for approximately 3 seconds to turn off.
POWER ON/OFF Ii BRIGHTNESS ADJUSTMENT
The MROS features a 4 MOA dot and 8 brightness intensity settings with a
55,000+ Hours battery life when used at middle brightness.
Power On:
Apply a single press to the left side activation button.
Power Off:
Press and hold down the left side activation button for approximately 3
seconds.
Brightna11 Adjustment:
Applying a single press to the activation button will cycle through one power
intensity at a time. Upon powering on, the MROS defaults to its middle
brightness and will first cycle down to its lowest
with additional presses. Once at its lowest, it will then cycle to its highest
brightness and proceed to work its way back down with additional presses.The
MROS does not feature an automatic shut-off.
MADS INSTALLATION
The MRDS’ mounting base uses the Trijicon RMR” standard footprint. Be aware of
potential differences in mounts, optics-ready pistol slide systems, adaptor
plates, milled slides, screw specifications, etc. despite being advertised as
compatible with the same footprint. (See our website fer more compatibility
information]
PISTOL APPLICATION
While following all basic rules of firearms safety, first ensure the pistol is
unloaded by removing the magazine end confirming the chamber is empty. Once
confirmed that the pistol is unloaded, process to field strip the pistol per
the manufacturer’s disassembly procedure. You will be working with just the
pistol’s slide.If applicable, remove the slide’s cover plate to gain access to
the slide’s optic interface. Piece the MRDS onto the slide ensuring ell screw
holes ere aligned end the MRDS is seated flush. A pair of #6-32 and #4-40 Torx
screws are included with the MRDS and are commonly used for most mounts,
optics-ready pistol systems, and aftermarket milled slides. Recommended torque
value is 15 in lb. No additional thread locking compound is required as it has
already been pre-applied to the screws.
Note that some optics-ready pistol platforms come included with specific
screws end or adaptor plates that may be required and or are better-suited fer
installing the MRDS. It is important to read
the manufacturer’s procedures in addition to ours. We still recommend a torque
value of 15 in-lbs. and additional thread locking compound ~ not already pre-
applied. Reassemble the pistol per the manufacturer’s reassembly procedure.
While following all basic rules of firearm safety, function check the pistol.
MDUNT APPUCATIDN
Place the MRDS onto the mount ensuring all screw holes are aligned and the
MRDS is seated flush. A pair of #6-32 and #4-40 Torx screws ere included with
the MRDS and are commonly used for
most mounts, optics-reedy pistol systems, and aftermerket milled slides.
Recommended torque valueis 15 in-lbs. No additional thread locking compound is
required as it hes already been pre-applied to
the screws.
Note that some optics-ready pistol platforms come included with specific
screws and or adaptor plates that may be required and or are better-suited fer
installing the MRDS. It is important to reed the manufacturer’s procedures in
addition to ours.We still recommend e torque value of 15 in-lbs. and
additional thread locking compound if not already pre-applied.
ZERDINll 1NE URDS
The MADS comes out of the box mechanically centered with a flathead adjustment
tool provided. To move the Point of Impact [POii to the right, turn the
windage adjustment screw located on the right-hand side of the MRDS
counterclockwise. To mDV8 the POI to the 111ft, turn the windage adjustment
screw clockwise. To move the POI up, turn the elevation adjustment screw
located on the top rear of the MRDS counterclockwise. To move the POI down,
turn the elevation adjustment screw clockwise. The MRDS is zeroed when the
point of impact CPDll overlaps the point of aim CPOAJ et your specified target
distance confirmed through live-fire. No Dot: Check battery is installed
correctly, Check battery has power or is new, Check battery is CR2032. Check
for dust or derbies blocking LED.Not holding zero: Check optic is properly
mounted with RMR footprint and with 15 in-lbs of torque. Make is sure to use
provided screws recommended for your mounting platform.
MAINTENANCE
Maintain the surface of the MRDS by removing any dirt or sand with e clean so~
cloth or Q-tip. Wipe the lens and emitter lens with e clean s~ cloth or Q-tip
to keep it clean and dry. Do not touch
the lens with fingers or finger nails to clean the lenses. Store the MR□S in a
cool and dry place when not in use. Avoid contact with acid, alkaline, or
corrosive chemicals. Remove battery if being stored for an extended period of
time.Do not attempt to lubricate any part of the MRDS. Do not disassemble the
MRDS. Any such action will void the warranty. Viewing the sun can cause
serious eye injury. Never look directly into the sun with this or any OP3
Micro.
THE BEST NEVER REST WARRANTY – UFmME
Leapers, Inc. warrants that all UTG & UTG PRO products conform to published
specifications and are free from defects in material and workmanship. We will
repair or replace defective products for the duration of the product’s lifa
span. Our dedicated in-house customer service professionals will provide the
best-enclosure experience.
NOTES:
Our warranty does not extend to products disassembled, damaged from misuse,
accidental impact, negligence, natural disasters/accidents, or unauthorized
repair or alteration. For any questions regarding the process, please feel
free to call us at [7341542-1500 or email us at
oflice@leapers.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>