OCEAN DIVERS GDC100-CD Wireless Charge Dock User Manual
- June 11, 2024
- OCEAN DIVERS
Table of Contents
OCEAN DIVERS GDC100-CD Wireless Charge Dock
Specifications
- Transmission Capacity : Up to 5W
- Operational Frequency: 113 KHz ~ 205KHz
- Input: 5V
- Output: 5V
- Dimensions: 45.31 mm x 62.34 mm x 18.36 mm
- Weight: 16.5 grams
- Max Input Current: 1.5 A
- Max Output Current: 1.0 A
Product Usage Instructions
Charging the Dive Watch Battery via a Wireless Charger
- Plug the wireless charger’s power adapter into a power outlet and connect the USB type C cable to the wireless charger. The indicator light will flash upon connection.
- Place your dive watch on the wireless charger ensuring the device’s back makes contact with the charger and is centered.
- Ensure the wireless charger and device backs are facing each other for proper charging alignment.
- The watch will start wirelessly charging when placed on the dock, and the screen will display “CHARGING”.
- To stop charging, separate the devices. The wireless charger will turn off automatically after 60 seconds if no device is detected.
Notes:
- Avoid exposing the wireless charger to water as it lacks the same water-resistance certification as the watch.
- Dive Mode functions are disabled during charging.
- For efficient charging, ensure proper alignment of transmission and receiver coils by placing the watch flat against the charging dock.
FAQ
Q: What should I do if my device is not charging wirelessly?
A: Ensure that the device’s back is making proper contact with the wireless charger, and both are properly aligned. Make sure there is no large air gap between the device and the charger for efficient charging.
Q: Can I use the wireless charger near water?
A: No, it is recommended to avoid exposing the wireless charger to water as it does not have water-resistance certification like your watch.
Q: How do I know if my device is charging?
A: Your device will display “CHARGING” on the screen when placed correctly on the wireless charger.
DEVICE OUTLET
The wireless charger can provide up to 5W transmission capacity and enables
powering or charging for any WPC‐ Qi-certified products
LED indication scheme
| LED (Blue) | Operational Status |
|---|---|
| Power ON | Charging |
| 3-second Blink Fast | Blink Slow |
Specification
| Rating | Input: | 5V | Volts: | 1.5 A (max) |
|---|---|---|---|---|
| Output: | 5V | Volts: | 1.0 A | |
| Operation Frequency | 113 KHz ~ 205KHz | |||
| Dimension: | 45.31 mm x 62.34 mm x 18.36 mm | |||
| Weight: | 16.5 gram |
CHARGING
Follow these steps to charge the dive watch battery via a wireless charger:
- Firstly plug the wireless charger’s power adapter into a power outlet and the USB type C cable into the wireless charger. The indicator light on the base will flash when you first connect the cable.
- When you’re ready, place your dive watch on the wireless charger.
- For it to charge properly, the device’s back should make contact with the wireless charger, and the device should be centred. Wireless chargers should be closed and also have their back facing the charging pad.
- The watch charges wirelessly when mounted on the included dock and the screen shows “CHARGING”
- To stop charging, just separate the two devices from each other. The wireless charger feature will automatically turn off after 60 seconds when no other device is detected.
Note:
- Do not expose the wireless charger to water because the wireless charger does not have the same water-resistance certification as your Watch.
- Dive Mode functions are not available while the watch is charging.
- Wireless chargers quickly lose efficiency when the transmission and receiver coils are not aligned properly or there is too large an air gap. Ensure the watch is flat against the charging dock for the fastest, most efficient charge.
FCC Warning
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference
- this device must accept any interference received, including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, under part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used under the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The FCC certification of this device refers to RF exposure testing performed in typical operating conditions, where a person is no closer than 20 centimetres from the device surface at all times, except for non-repetitive patterns with transient time intervals in the order of a second. Only in the stated conditions, the device is shown to fully comply with the FCC RF Exposure requirements of KDB 447498.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>