belena M32392 AquaSpa Foot Bath Instruction Manual
- June 8, 2024
- belena
Table of Contents
belena M32392 AquaSpa Foot Bath
Description
Scope of delivery and description of the parts
- ON/OFF switch
- On/off switch for spa water + vibration
- On/off switch for heat/infrared
- Practical water splash guard and transport handle
- Infra-red light
- Massagelvibration nubs
- Foldable silicone wall
- Stable, non-slip rubber feet
IMPORTANT SAFETY INSTRUCTIONS
- Read all instructions carefully, even if you are familiar with the appliance.
- Before cleaning or when not in use, remove the plug from the mains.
- Never pull on the cable. Never carry the appliance by pulling or lifting it by the cable.
- Only ever use the appliance for its intended purpose. This product is intended for domestic use only.
- Never use the appliance outdoors.
- Never attempt to retrieve a appliance that has fallen into water. Unplug the power cord
- Never leave the appliance unattended while it is in operation.
- NEVER operate while bathing or showering.
- Do not use any accessories that are not expressly recommended by the supplier
- Children should not play with the appliance.
- Cleaning and user maintenance must never be performed by children without supervision.
- Never operate the appliance if the power cord or plug is damaged, if it does not work properly, if it has been dropped or damaged, or has fallen into water.
- Return the appliance to a customer service centre for inspection and repair. Always keep the power cord away from hot surfaces.
- Only use the appliance while seated.
- Never use on particularly sensitive areas of skin or upon areas with poor blood circulation.
- Pregnant women and people with diabetes or similar illnesses should consult their doctor before use
IMPORTANT : Your Belena Aqua Spa is foldable – for easy and quick
storage
Information about your appliance:
- The spa bath is started together with the vibration (a)
- The heating function + infrared light can – if required – be switched on separately (b)
- The maximum temperature is 42°C.
- The appliance is suitable for feet up to shoe size 46.
INSTRUCTIONS FOR USE:
- Check that the appliance is unplugged before filling it with water.
- Only fill water up to the MAX line – never fill water above the MAX line. Also pay attention to the minimum amount of water that is required – MIN line on the appliance
- Switching on the appliance
- Do this via the switches – see #1A
- On/off switch for spa water + vibration
- On/off switch for heat+infrared
- You can also use the functions separately:
- Bubbles and vibration
- Heat and infra-red
- Heat, infra-red, bubbles and vibration
Note:
- It takes approx. 45 minutes for the water to heat up, depending on the initial water temperature and the filling quantity.
- if you want this to happen faster, fill the basin with warm water.
- Sit on a comfortable chair (e.g. an armchair or sofa), put your feet in the basin and enjoy.
- Before emptying: Disconnect the appliance from the mains.
CLEANING
Unplug the appliance and allow it to cool down before cleaning. Only dry the
appliance with a soft, damp cloth. Make sure that no water or other liquids
ever come into contact with the switches. After cleaning, wipe the surfaces
with a dry cloth. Never use abrasives, detergents or cleaning agents.
STORAGE
Unplug the appliance and allow it to cool down. Put the appliance in its
packaging and store in a clean, dry place. Never wrap the cable around the
appliance, in order to avoid cable breakage. Never hang the appliance by its
power cord.
TROUBLESHOOTING
TROUBLESHOOTING
PROBLEM| POSSIBLE CAUSE| SOLUTION
The appliance is not working properly| The appliance is not plugged in.|
Connect the applian- ce to the mains.
The switch is not in the ON position.| Press the on/off switch.
The water temperature is too low| The appliance needs up to 45 minutes to heat
the water to up to 42°C.| Tip: to save time, fill the basin with warm water.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>