Innovative Ergonomic Solutions WINSTON-E Sit Stand Dual Monitor Mount Instruction Manual
- June 4, 2024
- Innovative Ergonomic Solutions
Table of Contents
WINSTON-E Sit Stand Dual Monitor Mount
WINSTON-E® DUAL
Installation Instructions
Innovative Ergonomic Solutions 800 524 2744 customerservice@team-ies.com team- ies.com
HAT Collective 408 437 8770 cs@hatcollective.com hatcollective.com
PAGE 1 OF 11
© 2022 Innovative Ergonomic Solutions REV A
WARNING
WARNING: FAILURE TO CAREFULLY FOLLOW ASSEMBLY, SAFETY, AND OPERATION
INSTRUCTIONS AND WARNINGS REGARDING THIS PRODUCT MAY RESULT IN BODILY INJURY
AND/OR PROPERTY DAMAGE.
Liability: The manufacturer does not accept warranty claims or liability
claims for damages arising from improper use of Winston-E. For safe use, do
not place any objects or body parts underneath the worksurface. Make sure no
body parts, objects or furnishings are located above the Winston-E. When using
Winston-E, make sure no hands, fingers or other body parts are near the
lifting column or between the cross beam and worksurface. Winston-E must be
set on a level, stable surface for safe use. Additional Warning: Do not use
Winston-E if it has a damaged cord or plug. Winston-E should not be carried by
the cord. Pull on the plug, not the cord, to unplug Winston-E. Keep liquids
away from Winston-E. Keep hair, loose clothing, fingers, and body parts away
from openings and moving parts. Switch off power supply and remove main power
supply plug before installation or troubleshooting. Ensure no cables or cords
can get jammed or stripped when raising or lowering Winston-E. Ensure all
wires are not entangled in the Winston-E and have enough length when the unit
is raised to the desired height. WINSTON-E IS NOT A TOY. Children should not
use Winston-E. Do not crawl, lie, or move around the unit. Do not sit, kneel,
or stand on the worksurface. Do not use Winston-E if you are distracted or are
under the influence of medications that can cause diminished control.
Winston-E is not a toy and should only be installed and used by someone
familiar with and capable of adhering to the warnings and instructions.
WARRANTY
Winston-E includes a 5 year limited warranty. This limited warranty covers any
defects in materials and workmanship of the product. This limited warranty may
not cover problems, damage or injuries caused by misuse, accidents or abuse.
The manufacturer may require proof of purchase before performing any repairs
or replacing products during the warranty period. This warranty is non-
transferable and applies only to the original purchaser.
PAGE 2 OF 11
PARTS LIST
A
Freestanding Base 1x F
412268
Utility Tray 1x K 412269
Monitor Tilter 2x P 8500 Tilter
B
M6 x 1 x 16mm FPhMS 4x G
702013
Left Wing 1x L 312270-12.5-L
M4 x 12mm Phillips Pan Head Screw (4-pack) 2x Q 702096
C
Worksurface 1x H
111700
or
Compact Worksurface
112896
D
M6 x 1 x 25mm FPhMS 4x I
711870
Right Wing 1x M 312270-12.5-R
Cap 1x N 112057
Dog Washer 2x R 111230-603
10-32 x 1/2″ FHSCS 2x S 711240
E
Worksurface Plate 1x J
Quick Connect VESA Plate 2x O
111701
114808
Column Cable Clip 2x 112626
PAGE 3 OF 11
Wing Cable Clip 2x 112082
3/32″ Allen Wrench 1x 700146
1/8″ Allen Wrench 1x 701312
7/32″ Allen Wrench 1x 701127
1
2
A
3
4
B
B
PAGE 4 OF 11
5
C
6
D E
PAGE 5 OF 11
7
F
8
i
Place the utility tray on top of the work surface by aligning the (4) tabs on
utility tray with recessed areas on worksurface plate.
With the tabs aligned, slide utility tray towards the column to secure into
place.
PAGE 6 OF 11
9
G
2x
i
Tension can be tightened or loosened as shown.
3/32″
10
I H
PAGE 7 OF 11
11
2x
J L
PAGE 8 OF 11
12
2x
K PAGE 9 OF 11
13
2x
i
TILTER FRICTION ADJUSTMENT
1/8″ R
1/8″
M
N
PAGE 10 OF 11
14
15
2x
P
2x
O
PAGE 11 OF 11