ANGELWING DESIGNS Micro Dammit-E Instruction Manual
- June 8, 2024
- ANGELWING DESIGNS
Table of Contents
ANGELWING DESIGNS Micro Dammit-E
INTRODUCTION
The Micro Dammit is designed for intermediate to advanced pilots. Whilst not a
difficult model to fly please bear in mind that it is very small, very fast, and
extremely agile.
Building is very quick and simple, but again some building experience or the
assistance of a skilled model maker is suggested. Small models need to be
built carefully and accurately to get the best flying performance possible.
Only lightweight covering should be used in order to reduce the risk of twis
ng the airframe out of shape when shrinking the film. We used Oracover Oralight
on our prototypes. Our feather cover is ideal but as it is totally clear a
high visibility s cker scheme would be required unless flown slowly and close.
Balancing a flying wing is very important. The CG is shown on the plan and
should not be any further back than indicated, especially for test flights.
Launching is easy at 1/3rd thro le with a gentle overarm launch. Once your
familiar with the behaviour of the model you can launch from a wing p with a
very gentle side are launch if preferred.The Micro Dammit is designed for
intermediate to advanced pilots. Whilst not a difficult model to fly please bear
in mind that it is very small, very fast, and extremely agile.
Building is very quick and simple, but again some building experience or the assistance of a skilled model maker is suggested. Small models need to be built carefully and accurately to get the best flying performance possible.
Only lightweight covering should be used in order to reduce the risk of twis ng the airframe out of shape when shrinking the film. We used Oracover Oralight on our prototypes. Our feather cover is ideal but as it is totally clear a high visibility s cker scheme would be required unless flown slowly and close.
Balancing a flying wing is very important. The CG is shown on the plan and should not be any further back than indicated, especially for test flights. Launching is easy at 1/3rd thro le with a gentle overarm launch. Once your familiar with the behaviour of the model you can launch from a wing p with a very gentle side are launch if preferred.
Recommended addi onal items
- 2 x Kingmax 4g Micro Digital servo (2.5g to 5g Servo, max thickness 9.5mm)
- 1 x 4-6 Channel end pin Receiver ( eg Spektrum AR6110E)
- 1 x 1404 Brushless motor 3000kv – 4600kv (we used iFlight Xing 1404 4600kv from HobbyRC) 1 x 6-12 amp Brushless esc with BEC (we used TMotor AT12amp Fixed wing esc from Hobby RC) 1 x 4030 Prop (we used Nazgul T4030 (1.5mm) 2 Blade prop from Hobby RC)
- 1 x 2s 350mah Lipo (we used GNB 350mAh 2S 70C LiHV Ba ery (PH2.0 Cabled) from Hobby RC)
Covering Materials
- We used Oracover Oralight. Other suitable coverings are Angelwingdesigns Feather cover, Solarfilm Solite (now discon nued) Hangar 9 Ultracote parklite (freely available is USA)
Adhesives
- Thin / medium CA for Carbon to Balsa, Balsa to Balsa Superpha c for wood to wood joins
- Contact adhesive to mount the servos
Misc
- Velcro for ba ery moun ng
- 1.5mm / 2mm Heatshrink sleeving for motor to esc leads Small Cable e to mount esc
- M2 x 3mm Screws to mount the motor
Important Notes
- Make sure the motor bolts do not protrude into the motor windings.
- Make sure the motor rotates freely, enlarge the hole in the plywood motor mount it the circlip cathes
- Make sure you install the motor mount correctly. The moun ng holes are offset
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>