LEADER FOX K23 Altar Power Ride Instruction Manual
- June 15, 2024
- LEADER FOX
Table of Contents
E – BIKE POWER RIDE
Altar
Electric Bicycle Operating
Instructions
Under the law, the dealer is obliged to attach the LEADER FOX Electric Bicycle Operating Instructions to every product
Introduction
Dear users,
Please read carefully all the information regarding your E-LF product to
ensure optimal functioning of your e-bike. The following text containing a
comprehensive description will provide you with information on all aspects and
details (including installation, setting up and general use of the display)
regarding the use of our display. This instruction document will also help you
solve potential problems and failures.
What is an electric bicycle?
Electric bicycle is a conventional bicycle with an electric drive added to
assist the rider. The motor function is actuated by pedalling, which is
scanned by a special sensor installed in the pedal hub. Therefore, you have to
keep pedalling on an e-bike, the motor is there only to help you. You can set
an electric bicycle in motion also using a control button or an accelerator
but only up to the maximum permitted speed of 6 KMPH (e.g. for walk
assistance). The maximum speed of an e-bike with motor assistance is 25 KMPH,
with a 10% tolerance (when this speed limit is reached, the motor switches off
and you need to pedal just like with a regular bicycle). When your battery
runs out of power or your motor is off, you can ride your electric bicycle as
a conventional bike, without any resistance at all.
From the point of view of the Road Traffic Act, an electric bicycle whose
features conform to European standard EN 15194-1 is regarded as a regular
bicycle, i.e. you can ride on bike trails, do not need a driver’s license and
a helmet is mandatory only up to 18 years of age.
Description
Factors influencing the electric bicycle range
- Rolling resistance of the tyres. Leader Fox e-bikes are fittet with tyres with low rolling resistance and increased resistance to puncture. It is also important that the tyres are inflated properly. Therefor, if the tyres of your electric bicycle are underinflated, the range will decrease.
- Weight of the electric bicycle. The lower weight of the electric bicycle, the greater the range.
- Battery status. It depends on whether the battery was fully charged before your trip. It is also to be expected that the higher the number of discharge cycles the battery has undergone, the smaller capacity it has.
- Profile and surface of the track. The higher the elevation difference and the steeper hills you negotiate and the worse surface, the shorter the range.
- Riding mode. It depends on which of the three riding modes you have set.
- Continuity of riding. The more braking and acceleration, the shorter the range.
- Air resistance. For example, it depends on whether we ride a bicycle with low frame and sitting upright or whether we ride sporty bicycle with seat set to the same height as the handlebars.
- Wind strength. The stronger the wind we have beck, the longer the range and vice versa.
- Weight of the rider and load. The greater the weight, the shorter the range.
- External temperature. The lower the temperature, the less battery capacity can be used while riding.
Electric set
M510
The system uses monitoring of torque, monitoring of speed of the pedal
assist system and monitoring of real speed of wheels.
The system uses a dual protection feedback for measuring the speed signal to
ensure safety and reliabilityof the system.
It has high starting torque, maximum torque of over 95 Nm, suitable especially
for riding uphill.
It is highly efficient with low power consumption, long range, low noise
levels, and smooth operation.
Description and scope of operation:
The motor unit works properly under the following operating conditions:
Temperature range – 20 + 55°C
Relative humidity – 15 – 95% RH
Maximum torque – ≥ 95
Weight – 3Kg
Noise – <55 dB
Dustproof/ waterproof – IP66
Certified – CE ROHS/ EN14766/ EN114764/ REACH
Description of the power unit is placed on the cover and shows the following
information:
MM G522.250 15 033 F5 S329 0001
MM – Mid motor
G520 – Engine model
250 – Rated engine power
15 – Number of winding turns
033 – Connection combination sort
F5 – Measurement and control equipment number
S329 – Date of manufacture, indicating i tis manufactured on March 29, 2018
0001 – Production seriál number, ranging from 0000 to 9999, 0001 is the
production seriál number of the first motor
Dimensions of the power unit:
Safety instruction
Battery:
Do not throw the battery into fire.
Do not throw the battery into water.
Do not use the battery for other appliances. It has been made specifically for
this model.
Do not dismantle or modify the battery.
Do not connect the positive and negative poles of the battery.
Charger:
Do not dismantle or modify the charger.
Do not use the charger for other appliances. It has been made specifically for
this model.
Do not throw the charger into fire or water.
Do not touch the charger with wet hands.
Keep the charger from animals or children.
Do not cover the charger.
Do not use the charger if it is broken
Battery
Battery charging and maintenance:
Charge the battery in a dry enviroment to avoid short-circuit damage.
Charge the battery to at least 60% of the capacity once every 3 months even
when the bicycle is not used.
Do not cover the battery or the charger.
Do not leave the battery constantly connected to the power source.
Do not use the battery for other appliances. It has been made specifically for
this model.
Do not disassemble or modify the battery pack.
Do not throw the battery into fire or expose it to extreme temperatures.
Recharging time from zero to 100% is 1-7 hours.
Drive warranty:
The warranty applies to those drive parts that are not sensitive to improper
handling (pack, electronics, charger, etc.); such parts are covered by a
24-month warranty.
The warranty does not apply to chemical parts of the battery and to capacity
reduction due to normal use (39% after the expiry of two years); those parts
are covered by a 12-month warranty.
Charging:
The battery is the most expensive part of an electric bicycle; therefore, pay
increased attention during handling, charging and storage. The battery is
sensitive to precise charging. Therefore, it is necessary to charge Li-Ion
rechargeable batteries using only a charger supplied by us. Connect the
charger to 220-240 V power outlet. 5A protected circuit is sufficient. The
charger will automatically suspend charging when full capacity of all cells is
reached.
We recommend discharging the battery in full after each ride to ensure that
your battery will be up to its full capacity for your next ride. Charging the
battery may last 1 to 5 hours depending on the condition of the battery cells.
Charge it exclusively in covered dry areas (moisture and dripping water can
damage the charger) at a temperature of 5 to 40°C.
The charging process is indicated by a red glowing LED. It will turn green
when the battery is charged and the charging process is complete. The battery
contains a charge-monitoring indicator (when the charge indicator button is
pressed, the light indicator will come on).
Normal battery behaviour:
If the motor stops running smoothly and switches to intermittent operation, it
could be a sign of low battery capacity. In that case switch off the electric
drive system and continue without motor assistance, as if riding a
conventional bicycle.
Battery warming is normal and does not indicate any defect. The battery is
protected by a temperature sensor and switches off automatically in case of
excessive overheating. Wait until the battery cools down to its normal
operating temperature and then ride on.
If you feel your total battery capacity has dropped, it could be caused by
charging or operation in suboptimal climatic conditions. Carry out 3 full
charging cycles. Fully discharge the battery while riding and then charge to
its full capacity at room temperature.
If the charge indicator shows that the battery is discharged, there is still a
minimum voltage level in it which protects it against damage but is not enough
to power the electric bicycle. Recharge the battery as soon as possible. Never
leave the battery fully discharged, it could results in its damage.
In the case, that the battery will be turned on more than 30 min and bike will
not be used, the battery will be automatically switched off.
Battery si fully shutdown after 48h. After that time period you have to first
activate the batter by switch button or connect battery with charger.
Proper care of the battery prolongs its life.
LCD display
Product:
Intelligent display DP C241.CAN
Supplier:
Bafang
Electrical parameters:
Battery supply 36V
Rated operating current 12mA
Off leakage current < 1 uA
CAN BUS protocol
Maxoutput current 30mA
Maxoutput current to controller SOmA
Operating temperature — 20 ~ 45 °C
Storage temperature — 30 ~ 70 °C
LCD dimensions and materials:
Pradcut shell is ABS, transparent window is made withhigh strength Acrylic.
Can be used up to -20°C.
CE / IP6S water proof / ROHS.
LCD Display description:
Threebutton console which is with BOOST mode is more user-friendly.
Speed indication: Indudes maxamum speed, average speed.
Unit switch between imperial and metric.
Intelligent battery capacity indication.
Control and indication for the headlight.
5 levels of backlight brightness setting.
Indication for power assistance level with 6 levels: 0/1/2/3/4/5.
Indication fer trip: To indicate single-trip distance, total distance and
remaining distance.
Multiple data indication: Indication for the remainang distance, Indication
for the consumption of energy CALORIES. (Note: if the display has this
function. }
Record and indication for the error information.
Button with feedback of haptic vibration.
Control and indication for push assistance.
Parameters resettable with BESST BOX.
USB charging port: ≤ 5V, ≤ 1A.
Dual Bluetooth integrated.
Maximal range:
Maximal range is set with fully charge battery and flat terrain and little bit
of headwind. Average range is calculated with ideal set of the assist and
slightly hilly terrain.
Assembly instructions
Display assembly:
Please pay attention to the tightening torque of screws. Damage caused by
excessive tightening torque or incorrect assembly / disassembly is not covered
by warranty.
Control
Turning on the electrical system of the ebike
Before switch on of the system please check electrical wiring.
Switch on power of the electrical systern on battery, colored backlighting
illuminates.
Switch on display with press and short hold (1,5 second) “ON/OFF” button.
Display will automatically turns off if it is not used for a while.
After ride turns off e-bike in the same way.
For better gear change is appropriately stop pedaling for a while.
Before nde please lock battery in frame and take out the keys.
Assist level operating
Short press “UP/DOWN” buttonc can change the assist level. Off is without
asistance. 0 is without assistance. 5 is the highest jevel of assistance.
Walking mode
Press and hald GOWN button for 2 second can get inte walking mode, out of
the mode when release the button.
Walk assistance speed depends on gear ratio. Lower gear ratio / slower speed,
higher gear ratic/ faster speed.
Speed and mileage mode switch
Briefly press “BOOST” button to switch to different data interfaces, then
circularly to show singfe trip distance (Itip.km) -> total distance (ODO,kin)
maximum speed (MAX,km/h) > average speed (AVG,kmn/h) > remaining distance (RANGE,km) > energy consumption (CALORIES/CAL KCal) > riding time (TIME,min) > real-time output power (POWER,w). Battery capacity indication:
The battery remaining capacity will be indicated as the exact percentage, in addition, the frame of the symbol will flash at 1Hz when capacity is less than 5%, means the battery needs to be charged.
Headlight/Bacidight On/Oft
Press and hold “+” to tum on the display backlight as well as headlight,
this moment you will see the symbol! of headlight in the screen; On the
contrary, press and hold “+” again to turn off the display backlight and the
headlight (If the display is turned on in a dark environment.the display
backlight/ headlight are turned off manually, they also need to be turned on
manually afterwards).
Bluetooth connection:
This display has Bluetooth module inte-grated and connectable te BAFANG’s
own smart phone application “BAFANG GC’. In addition, the SDK is open for
customer to develop APP indrvidually.
This display is also connectable to the chest belt and catch real-time heart
beat data from the chest belt and display it and send the data to smart phone.
The list of data transmit from display to smartphone as below:
Item | Data |
---|---|
1 | Speed |
2 | Capacity |
3 | Support level |
4 | Data of battery |
5 | Output of sensors |
6 | Remaining range |
7 | Calory |
8 | Component info. |
9 | Current |
10 | Heart best |
11 | Trip |
12 | ODO |
13 | Headlight status |
14 | Error code |
Parameter setting
Press and hold “+” & “-” button synchronously to enter into Display Setting
interface, and briefly press “+ or “~~” ta switch to from “Setting” to “EXIT”
and then briefly press “ON/OFF” button to confirm the operation.
Unit (Km/ mile):
Briefly press “+” or “-” to go to “UNIT, and then briefly press “ON/OFF”
to switch between “Metric’/ “Imperial’, then briefly press “ON/OFF” to confirm
selection and save the setting and exit back to the “UNIT. Press and hold “+
and -” synchronously to save and exit back to the main interface or you can
atso select “BACK” -> “EXIT” to exit back to the main interface.
Auto Off
Briefly press “+” or “-” ta go to “Auto Off”, and then briefly press
“ON/OFF” to select among OFF”/”9″/”8″/7″/”6 ”/”5″/”4″/”3″/”2”/”1″ “ten
levels, then briefly press “ON/OFF to confirm selection and save the setting
and exit back to the “Auto Off’. Press and hold “+” and -” synchronously to
save and exit back to the main interface, or you can also select “BACK” →
EXIT* to exit back to the main interface.
Notice: “OFF” means this function is off, the unit is minute.
Brightness setting
Briefly press “+” or -” to 20 to “Brightness”, and then briefly press
“ON/OFF” to select among “100%” /”75%”/ “50%”/”30%” /”10%” five levels, then
briefly press “ON/OFF” to confirm selection and save the setting and exit back
to the “Brightness”. Press and hold “+” and “-” synchronousty to save and exit
back to the main interface, or you can also select “BACK” > “EXIT” to exit
back to the main interface.
Notice: “10%” is the weakest brightness and 10096” is the strongest
brightness. Indication switch of output with current or power
Briefly press “+” or “-” ta go to “Power View”, and then briefty press
“ON/OFF”, then briefty press “+” or “- to switch between Power and Current,
then briefly press “ON/OFF” to confirm selection and save the setting and exit
back to the “Power View”. Press and hold “+” and “-” synchronously to save and
exit back to the main interface or you can also select “BACK” > “EXIT*to exit
back to the main interface.
Light sensitivity setting
Briefly press “+” or -” to 20 to “Sensitivity”, and then briefly press
“ON/OFF” to select among“0″/”1″/”2″/”3″/”4″/”5″ five levels, then briefly
press “ON/OFF to confirm selection and save the setting and exit back to the
“Sensitivity”. Press and hold “+” and -” synchroncusty to save and exit back
to the main interface, or you can also sefect “BACK” → “EXIT™ to exit back to
the main interface.
Notice: “O” means light sensor is off. Level 1 is the weakest sensitivity
and level 5 is the strongest sensitivity.
Trip reset – to clear the single tip distance
Briefly press “+” or “-” to go to “TRIP Reset”, and then briefly press
“ON/OFF” to switch between “NO”/“YES” (“YES”- to clear, “NO”no operation},
then briefly press “ON/OFF” to confirm selection; After confirmation, briefly
press “ON/OFF” again to save the setting and exit back to the “TRIP Reset”.
Press and hold “+” and “-” synchronously to save and exit back to the main
interface, or you can also select “BACK” → “EXIT*to exit back to the main
interface.
Not i ce: The riding time (TIME}, average speed (AVG) and maximum speed
([MAXS} will be reset simultaneously when you reset TRIP. Vibration
setting
Briefly press “+” or “-” to go to “Vibration”, and then briefly press “ON/OFF”
to select between ON and OFF {ON means vibration button is on; OFF means
vibration button is off}, then briefly press “ON/OFF” to confirm selection and
save the setting and exit back to the Vibration”. Press and hold “+” and “-”
synchronously to save and exit back to the main interface, or you can also
select “BACK” → “EXIT” to exit back to the main interface.
Speed limit information:
This value is preset at 25 km/h by law.
not within the scope of the warranty.
Battery information:
Bttery status information Auto Off:
Press UP/DOWN button to change the auto power off time, from 1 to 10 the
number represent time (minutes) to shutdown, default value is S minutes.
System info:
System status
Reset:
For choosing Yes/No use Up/Down buttons and for confirmation press “M” button.
Yes mean the data are resets. Data clearance:
By long press M button for 3 seconds enter to the Data clearance. For choosing
Yes/No use Up/Down buttons and for confirmation press “Mt” button. Yes mean
the data Trip, Trip time, AVG are clean.
Basic setting:
System is factory set. For changing these parameters contact your dealer or
producer.
Oo not change these parameters by yourself, you can damage the e-bike.
Damaged caused by anproper treatment is not within the scope of the warranty.
Maintenance
Regular maintenance:
-
maintain all components of the electric bicycle clean
-
use only the recommended and tested cleaning materials
-
regularty lubricate the chain with suitable oils
-
in winter, clean the electric bicycle after each ride and pay increased attention to removing salt from battery contacts and other connectors
-
while handling the electric bicycle, make sure the cables of the electric system are not damaged.
Damaged cables pose a risk of electricshock -
regularty check all connections for correct tightening and brakes for correct function. Check also individual parts of the electric bicycle for damage. For example: cracks on the frame, fork, handlebars, stem, damage to cables, damage to battery pack, etc.
Battery transport:
Battery transport is subject to the requirements of regulations on
dangerous goods. Private users may transport undamaged batteries on roads
without having to conform to other conditions.
In case of transport by commercial users or by third parties it ts necessary
to comply with special packaging and marking requirements (e.g. ADR
regutations)
Batteries should only be sent if the battery pack is undamaged. Plug toose
contacts and pack the battery to Prevent its movement in the packaging. Notify
the forwarding service that the transport concerns dangerous goods.
Battery storage:
Store the battery in a dry and well-ventilated place, out of reach of
direct sunlight and other heat sources. In case of cold storage it is
necessary to let the battery warm up to normal room temperature (20°C) before
putting into operation.
Never leave the battery fully discharged. It could result in its
permanentdamage. For long-term storage keep the battery fully charged.
However, do not store it while permanentty connected to the charger or
installed in the electric dicycle.
Li-lon batteries are fully recyclable. After expiry of the battery life you
can returnit at any collection point or your dealer.
If you use an e-bike in hard conditions (long-term use of the maximum
assistance}, for longer ride at higher temperatures (30 ° C or above}, in
direct sunlight or when the battery is partially discharged and a combination
of these situations is it possible that bike will automaticly swith off. This
is a fuse protecting the control unit against burning. We recommend stop the
ride and let the bike (control unit) cool down. little bit. This is not a
defect.
Possible problems and their solutions
In case of system failure perform its diagnostics or contact your dealer.
The control LCD display is not on:
- always make sure the battery is charged
- check whether the battery is inserted correctly, whether the battery switch is on
- check the connections of the control unit and the display
The motor does not start when the walk assistance button is pressed
- check the connection of the motor cable (at the motor and the control unit)
- check the connections of the control unit and the display
The motor does not start when rotating the pedal cranks (pedalling)
- check the connection of the pedalling sensor to the control unit
- check the distance between the pedalling sensor and the magnet disk (max. 4 mm)
- check whether the disk is firmly attached to the central axle and does not spin freely
- in case of use of compact-type pedalling sensor
Warning
When there is a problem with the electric bicycle, it can show error messages. LCD display will show the icon and an error code will be displayed on the speed display. Error codes are marked from 01 E~FF E; see their meaning in the table below.
Error code | Description | Solution |
---|---|---|
6 | Low battery voltage | Check battery voltage |
7 | High voltage protection | Check battery voltage |
8 | Hall probe error | Check motor |
9 | Three-phase supply error | Check motor |
10 | Controller over temperatue | Stop riding for a while |
11 | Overheating controller senzor | Check controller |
12 | Overvoltage controller senzor | Check controller |
13 | Overheated battery | Chcek battery |
14 | Motor’ temperature error | Stop riding for a while |
15 | Controller’s overheated | Stop riding for a while |
21 | Speed senzor error | Check the position of the senzor |
22 | BMS communication error | Change battery |
25 | Torque error | Check motor |
30 | Communication error | Check connectors |
Electric set warranty
Complaint procedure:
Submit any complaints concerning the electric set or the battery to your
dealer.
When filing a complaint, submit a proof of purchase and a warranty certificate
with the registered serial number of the battery and indicate the reason for
the complaint and a description of the defect.
Wrranty conditions:
24 months for electric bicycle components — applies to manufacturing and
material defects beyond normal wear and tear caused by use.
12 months for battery life — the nominal battery capacity does not drop below
70% of the total capacity over 12 months from the sale of the electric
bicycle.
Warranty conditions:
The electric set must be used exclusively for the purposes it is intended for.
The electric set must be used, stored and maintained in accordance with these
Operating Instructions.
A warranty claim shall expire:
If it is found out that the damage to the product is due to the user’s fault
(accident, inexpert handling beyond the framework of these Operating
Instructions, tampering with the structure of the electric bicycle or
connection of the electric system, improper storage, etc.).
Expiry of the warranty period.
The warranty onty applies to the first owner
Warning
If you do not understand any of the points in these Operating Instructions,
please contact the dealer for explanation. Please read the whole manual!
Do not lend the e-bike to persons not briefed in its use and operation.
Complaints resulting from improper handling will not be accepted.
The LF Energy electric bicycle is not intended for use by children under 15
years of age. Likewise, the electric bicycle cannot be used by persons unable
to pedal or handle it independently. The manufacturer is not to be held
responsible for any potential injuries or damage to the bicycle!
Ideal weather conditions for using an electric bicycle are dry days, when the
outdoor temperature is above 10°C. When used at lower temperatures, the
battery discharges faster due to physical phenomena. Using the electric
bicycle at temperatures below 0°C is not recommended.
Do not expose the bicycle to direct sunlight as it is fitted with a protective
temperature sensor for the electric motor.
Never submerge the battery, the charger and other electric components in water
or another liquid.
Never wash the electric bicycle in a pressure washer (WAP) and always remove
the battery before washing
It is forbidden to tamper with the connections of the electric motor, the
control unit and the battery. Violating this section may result in the
warranty not being acknowledged or in irreversible damage to the electric
bicycle.
DO NOT USE chargers and components other than the ones included with the
electric bicycle.
We cannot be held responsible for damage caused by use of other non-approved
goods
Enjoy
many pleasant and safe kilometres on your new electric bicycle.
Your Leader Fox Team
Czech brand of electric bicycles.
BOHEMIA BIKE
Address
Pujmanové 1753/10a, Nusle
14000 Praha 4
Development, design and manufacturing
Okružní 697
České Budějovice 37001
Phone: 388 314 885
Email: info@leaderfox.cz
Documents / Resources
|
LEADER FOX K23 Altar Power
Ride
[pdf] Instruction Manual
K23 Altar Power Ride, K23, Altar Power Ride, Power Ride, Ride
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>